Categories

Best Amplifier Wire

Rockville Rmh200w Single Din Marine Radio Waterproof Gimbal Housing, White

  • ...Pre-Wired Power(3 Wire), Speaker(8 Wire), RCA(2 Wire), Antenna. Makes installation easier! Here is how it works..
  • You take the speaker leads of your wire harness (for the 4 speakers) and connect them to the 8 wires inside the housing. You now connect the power and ground and remote wire..
  • If you are using an external amplifier, then connect the RCA's as well. Now you take the 8 speaker leads in the rear of the housing and connect those to your speaker wires..
  • If you have an amplifier you will plug the RCA in the back of the unit to your amplifier. You will also run the power wire from the rear of the housing to your 12 volt power source..
  • You will connect the black ground wire to anything metal. You can also connect the remote wire to the amplifier. U-shaped Mounting Bracket for Deck or Overhead Installation..
  • What is amazing about this is that because we have this feature it allows the wires to be enclosed in a waterproof housing which will ensure all your wiring and your receiver last for a long time..
  • Fully enclosed design provides protection from the elements. Stainless steel mounting hardware included. Rubber grommets for cable protection. Positive locking door mechanism..
  • One-piece mounting bracket. Fully adjustable mounting angle. UV Resistant Plasti....
Check Stock

Hifonics ZG-1800.1D ZEUS Gamma 1800w Car Audio Class D Mono Amplifier+Amp Kit

  • Package Includes: (1) Hifonics ZG-1800.1D ZEUS Gamma 1800 Watt Mono Amplifier Car Audio Class D Amp, (1) RockvilIe RWK41 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's.
  • Features of ZG-1800.1D: Low Noise Preamplifier Circuit: Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion, RCA Inputs: Nickel plated high temperature impact resistant with hex screw terminals that allow for secure connections and is erosion resistant, High Level Inputs: Easily tie into OEM audio systems that do not offer RCA output to maximize after market amplifier power, Operation Mode: Mono only.
  • Crossover Type: Onboard electronic crossover, Electronic Equalizer: Control of amplifier output with on-board electronic crossover to tailor specific frequencies to speakers and subwoofers, Class/Topology: "Class D, High efficiency with big power in a small footprint, Output Device Technology: PWM MOSFET Power Supply, Stable power through the PC board with minimal heat generation, Heat Sink: Aluminum, Old School Hifonics Heat sink for Superior Heat Dissipation..
  • Power Supply: Simpatico Coil Design, The dual coil Pulse Width Modulated power supply keeps voltage constant through the Ultra-Fi output devices, Output Connecti....
Check Stock

Pyle Car Stereo Wiring Kit - Audio Amplifier & Subwoofer Speaker Installation Cables (4 Gauge), Blue (PLAM40) & PAC SNI-35 Variable LOC Line Out Converter

  • Product 1: CAR AUDIO WIRING: Universal car stereo audio system cable and wire kit. Includes all necessary pieces to set up your amplifier and subwoofer speakers.
  • Product 1: INCLUDED AUDIO CABLES: 20’ ft. 4 gauge red power wire, 4’ ft. 4 gauge black ground wire, 20’ ft. 16 gauge blue remote turn-on, 20’ ft. 12 gauge stereo speaker wire.
  • Product 1: MORE AUDIO CONNECTION: 20’ ft. stereo RCA audio cable, 6’ ft. black split loom cable conduit - enables connection for amplifier and subwoofer speakers.
  • Product 1: CAR STEREO SOUND: Also includes (2) ring terminals 8G, (2) spade terminals: 8G, (5) spade terminals: 14-16G, (3) butt connector, (20) cable ties, (1) black grommet.
  • Product 2: Adjustable Line Output Converter.
  • Product 2: Use the SNI-35 when adding an amplifier to a factory radio to convert the radio's speaker level output to the lower amplifier (RCA) level input.
  • Product 2: Utilize Audio Transformer for Noise Isolation.
Check Stock

Rockville dB15 6000 Watt Peak/1500w RMS Mono 2 Ohm Amplifier+Amp Kit

  • Package Includes: (1) Rockville dB15 6000 Watt Peak/1500 Watt Dyno-Certified RMS Mono 2 Ohm Amplifier Car Audio Amp. (1) Rockville RWK01 0 Gauge....
  • Features of dB15: Rockville dB15 6000 Watt Peak/1500 Watt Dyno-Certified RMS Mono 2 Ohm Amplifier Car Audio Amp. Dyno Certified RMS Power Ratings:....
  • Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). - 2 Ohm: 6000 Watts x 1 Channel. - 4 Ohm: 3600....
  • Features of� RWK01: Rockville RWK01 0 AWG (American Wire Gauge) Complete Car Amp Installation Wire Kit. 17� � 0 Gauge Translucent Blue SuperFlex....
  • 17� Amplifier Remote Turn On Cable. Wire Ties and Ring Terminals, and all other accessories you need for a clean installation. Soft abrasion proof....
Check Stock

Rockville RXM-S30 Micro Marine/ATV Amplifier 2400w Peak 4 Channel 4x150W+Amp Kit

  • Package Includes: (1) Rockville RMWK4 4 AWG Gauge Waterproof Marine Amplifier/Amp Install Wire Kit. (1) Rockville RxM-S30 2400w / 600w Dyno-Certified....
  • Features of RMWK4: Rockville RMWK4 4 AWG Gauge Waterproof Marine/Boat Amplifier Wire Installation Kit. 20 � Translucent, Twisted Pair, High Quality,....
  • 25� 16 Gauge 100% Tinned-CCA, White, Non-Transparent Resin PVC, Flat Speaker Cable. 25� Blue Remote Wire. (1) Silver Mini-ANL Fuse Holder - Clear....
  • (2) Ring Terminals. (2) Spade Terminals. (5) Speaker Cable Terminals. (1) Washer. (10) White Cable Ties.
  • Features of RxM-S30: Rockville RxM-S30 2400w / 600w Dyno-Certified RMS 4 Channel Proton Micro Marine Car Amplifier. Dyno Certified RMS Power Ratings:....
Check Stock

Rockville RXD-M3 4000 Watt/2000W RMSMono Car Amplifier+100% CopperAmp Wire Kit

  • Package Includes: (1) Rockville RXD-M3 4000 Watt Peak/1000w Dyno-Certified RMS Mono 1 Ohm Amplifier Car Audio Amp. (1) Rockville RWK4CU 4 AWG Gauge....
  • Amplifier Kit Key Features of RWK4CU:: Rockville RWK4CU 4 Gauge 2 Channel Complete Car Amplifier Installation Kit 100% Pure Copper RCA Cables. 4 Gauge....
  • Kit includes: 17 ft. Frosted Blue 4 gauge power wire with seamless crimp ring terminal. 3 ft. Frosted Gray 4 gauge ground wire. 17 ft. Blue 18 gauge....
  • Three blue 12 gauge nickel-plated spade lugs. One black 4 gauge ring terminal. Ten 6" black zip ties.
  • Features of RXD-M3: Rockville RXD-M3 4000 Watt Peak/1000w Dyno-Certified RMS Mono 1 Ohm Amplifier Car Audio Amp. Dyno Certified RMS Power Ratings:....
Check Stock

4 Alpine SPE-6090 6x9 600 Watt Car Audio Speakers+4 Channel Amplifier+Amp Kit

  • (2) Alpine SPE-6090 6" x 9" 2 Way Pair Of Car Stereo Speakers Totaling 600 Watts. (1) Alpine BBX-F1200 600 Watt 4/3/2 Channel Amplifier Car Stereo Amp Class-A/B 2-ohm. (1)RockvilIe RWK42 4 Gauge 4 Chan Car Amp Wiring Installation Wire Kit (2) RCA's. 6" x 9" Type-E Coaxial 2-way Car Speakers. Polypropylene cone pearl mica injection. 3/4" Silk soft dome tweeter. Tweeter Magnet: Neodymium. Woofer Magnet: Ferrite. 4 ohms impedance. Square voice coil. Injection molded frame.
  • Peak Power Handling Per Pair: 600 watts. Peak Power Handling Each: 300 watts. RMS Power Handling Per Pair: 150 watts. RMS Power Handling Each: 75 watts. Frequency Response: 65-18,000 Hz. Sensitivity: 91 dB. Top-Mount Depth: 3". Mounting Diameter: 5-15/16" x 8-3/4". Features: Alpine BBX-F1200 600 Watt 4/3/2 Channel Amplifier Car Stereo Amp Class-A/B 2-ohm. Terminal Layout: Two-Sided. Screw Mount / Wire Cover: Integrated Wire and Mounting Screw Terminals.
  • Alpine BBX-F1200 600 Watt 4/3/2 Channel Amplifier Car Stereo Amp Class-A/B 2-ohm. Amplifier Type: Class-A/B. Channel Design: 4/3/2 Channel. Thermal Control: Thermal Management Control. Power Supply: DC-DC PWM Power Supply. Power Supply Design: MOSFET Power. Current Protection: Over-Current, Over-Voltage and Thermal Protection. Crossover:....
Check Stock

Boss Audio Armor AR3000D 3000-Watt Car Amplifier and 4GAMPKIT-SFLEX Q Power Super Flex 4-Gauge 3000-Watt Amplifier Car Audio Installation Kit

  • AMPLIFIER: RMS Power: 1200 Watt x 1 Channel @ 4 Ohm.
  • Max Power: 2200 Watt x 1 Channel @ 2 Ohm.
  • Dimensions: 6.5" W x 2.625" H x 13 5/16"L.
  • AMPLIFIER KIT: Handles up to 3000 watts of power.
  • Ready for complete amplifier installation.
  • KIT INCLUDES: Deluxe high quality fuse holder.
  • 17 feet of 4 gauge Super Flex orange power cable.
  • 3 feet of 4 gauge Super Flex blue power cable.
  • 25 feet of 16 gauge Super Flex speaker wire.
  • KIT SPECIFICATIONS: Dimensions: 13 x 8 x 3 inches.
Check Stock

Mr.Ho 10 AMP 12V Car Audio Radio Amplifier Noise Suppressor and Stereo Filter with Ground Loop Isolator

  • ELIMINATE NOISE -- H-density, lo-level wound torroid choke will eliminate ground loop noise between the audio source or audio amplifier. Keep a clear listening environment for you..
  • FUNCTION – It can reduce the noise in the audio system and reduce eliminates engine interference..
  • WIRES FEATURE -- Red wire for input, blue wire for output and black wire is ground wire..
  • EASY TO INSTALL -- Just splice the red wire to the line of 12V input, splice the blue one to the positive line, splice the black one to the ground wire..
  • SUITABLE ELECTRONICS – It is suitable for car audio, radio, amplifier stereo receivers, equalizers, and other mobile electronics..
Check Stock

DS18 AK8 Complete 8 Gauge CCA Amplifier Installation Wiring Kit - Ampkit Helps Make Connections Brings Power to Your Radio Subwoofers Speakers with Super Flex Wire - 960W for 1 Amplifier

  • COMPLETE AMPLIFIER WIRING KIT - AMPKIT8 is a perfect set to install 1 amplifier. 8 GA Installation cables 1000W that come with an ANL fuse holder with....
  • BLACK/RED WIRE - 17ft 2-channel shielded twisted pair of RCA premium audio cable inter-connections..
  • INSTALLATION PACKAGE - Install the amp wiring kit to 1 amplifier. All wire terminals, connectorss, wire ties, and wire loom are included in the box....
  • HIGH QUALITY MATERIALS - Super flex twist premium cables & Copper-Clad Aluminum (CCA) wires. Only the best materials are used with each kit..
  • EVERYTHING INCLUDED - 17ft 8 GA Red power cable / 3ft 8 GA Black ground cable / 17ft 12GA Red/Black speaker cable / 17ft 2Channel shielded twisted....
Check Stock

DS18 AK4 Complete 4 Gauge CCA Amplifier Installation Wiring Kit - Ampkit Helps Make Connections Brings Power to Your Radio Subwoofers Speakers with Super Flex Wire - 1200W for 1 Amplifier

  • COMPLETE AMPLIFIER WIRING KIT - AK4 is a perfect set to install 1 amplifier. 4 Gauge Installation cables 1200W that come with an ANL fuse holder with....
  • BLACK/RED WIRE - 17ft 2-channel shielded twisted pair of RCA premium audio cable inter-connections..
  • INSTALLATION PACKAGE - Install the amp wiring kit to 1 amplifier. All wire terminals, connectorss, wire ties, and wire loom are included in the box....
  • HIGH QUALITY MATERIALS - Super flex twist premium cables & Copper-Clad Aluminum (CCA) wires. Only the best materials are used with each kit..
  • EVERYTHING INCLUDED - 17ft 4 GA Red power cable / 3ft 4GA Black ground cable / 17ft 12GA Red/Black speaker cable / 17ft 2Channel shielded twisted pair....
Check Stock

Rockville SK510 PACKAGE 10 1200w Loaded K5 Car Subwoofer Enclosure+DB11 Amp

  • Loaded Sub Enclosure Features: Rockville Single 10" K5 1200w Car Subwoofer Pre-loaded In Vented Sub Enclosure, Peak Power Handling: 1200 Watts, Program Power Handling: 600 Watts, CEA Rated RMS Power Handling: 300 Watts.
  • Vent dimensions (inches): 2" x 6.5" x 8", Tuning frequency of enclosure: 35 Hz, 2" 4-Layer Black Aluminum Voice Coils Wound with OFC (100% Copper) Wire.
  • Features of Amplifier: Rockville dB11 1400w/700w RMS 2-Ohm Class-D Mono Car Amplifier and Bass Remote, CEA Compliant Power Ratings.
  • Peak Power Rating: (The amount of power the amplifier can produce for a split second at the loudest part of a song) - 2 Ohm: 1400 Watts x 1 Channel, - 4 Ohm: 880 Watts x 1 Channel, High-Speed MOSFET Power Supply.
  • Features of wire kit:, Rockville RWK81 8 Gauge 2 Channel Car Amplifier Wiring Installation Kit, (1) 17 High Grade Twisted Pair of 100% Copper RCA Cable, 17 8 Gauge Translucent Blue SuperFlex Power Cables, 17 18 Gauge Blue Remote Cable.
Check Stock

Crunch PX-1000.4 4 Channel 1000 Watt Amp A/B Class Car Stereo Power Amplifier with 300 Watt 3 Way CS Speakers and Soundstorm AKS8 8 Gauge Wiring Kit

  • Car audio bundle includes the Crunch PX-1000.4 4 Channel 1000 Watt Amp with (2) 3-Way Speakers and the Soundstorm Wiring Kit.
  • Class A/B Amplifier features Pulse Width Modulated power supply with Quick Thermal Dispersion Technology.
  • Speakers offer musical power with added resistance to the elements.
  • Great sound quality and added reliability.
  • 8-gauge amplifier installation kit with everything you need to install your amplifier in your car.
  • Wire kit includes 20-foot 8-gauge red power cable, 3-foot 8-gauge black ground cable, and 30-foot speaker wire.
Check Stock