Categories

Best Arduino Pro Mini 5v

Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino

  • Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
  • Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
  • The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
  • There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
  • Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
Check Stock

Hosyond 5Pcs D1 Mini NodeMcu ESP8266 ESP-12F Wireless WiFi Module Internet of Things Development Board Compatible with Arduino/WeMos

  • It is a mini NodeMcu Lua Wireless development board based on ESP-8266..
  • Compatible with Arduino IDE and WeMos D1 Mini..
  • 4M bytes, 5V 1A switching power supply onboard,1MB flash memory.
  • 11 digital input/output pins, all pins with interrupt/PWM/I2C/1-wire support (except D0).
  • 1 analog input (3.2V max input). Micro USB connection..
  • D1 mini development board compatible with Arduino WeMos and can be programmed in the compatible for Arduino IDE..
Check Stock

The Complete Country Guitar Method Compilation: Three Books in One! - Master Country Guitar Licks, Techniques & Soloing (Learn How to Play Country Guitar)

  • http://www.wch-ic.com/download/list.asp?id=127 (windows).
  • If you need an older driver, pls get it from GitHub—please read the link that follows immediate. http://sparks.gogo.co.nz/ch340.html.
  • More detals on how to use it please refer to: http://audiodiwhy.blogspot.com/2018/05/one-cheap-arduino-nano-clone-o-plus-one.html.
  • Small Arduino UNO Board:It is a smallest, complete and breadboard friendly board. It has everything that Arduino/Genuino UNO has (electrically) with more analog input pins and onboard +5V AREF jumper.More Breadboard Space:Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
  • Specification:The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.Usage: The Nano is 100% compatible with Arduino, with the same chips ATmega328P and CH340 with the official version..
Check Stock

HiLetgo 5pcs Mini ESP8266 ESP-12F Mini NodeMCU Lua 4M Bytes WiFi Module with Pin Headers

  • Arduino ompatibility. Using the Arduino IDE for programming.
  • 5V 1A switching power supply (switching power supply）onboard.
Check Stock

ACEIRMC ESP8266 ESP-12 ESP-12F NodeMcu Mini D1 Module for WeMos Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino,Compatible with WeMos D1 Mini 5pcs

  • This is D1 mini, it is a mini NodeMcu Lua WiFi board based on ESP-8266EX..
  • D1 Mini NodeMcu Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino, Compatible with WeMos D1 Mini..
  • 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
  • 1 analog input(3.2V max input). Micro USB....
  • WIFI development board,4M bytes.5V 1A switching power supply (switching power supply）onboard..
  • Our D1 mini development board compatible with Arduino WeMos and can be programmed in the compatible for Arduino IDE..
Check Stock

AITRIP 10PCS for Nano V3.0 ATmega328P Nano Board CH340 5V 16M Microcontroller Board, Compatible with Arduino Electronics Development Board

  • This board is using the chips ATmega328P and CH340, not FT232 as official Arduino.
  • More Breadboard Space:Nano's got the breadboard-ability of the Boarduino and the Mini USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND ）on one top, power and ground on the other..
  • The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source..
  • It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper..
  • you will get 10pcs Mini Nano V3.0 ATmega328P 5V 16M Microcontroller.
Check Stock

ACEIRMC SG90 Servo Motor Micro Servo 9G Servo Motor for RC Robot Arm Helicopter Airplane Remote Control (5 Pcs) (5pcs)

  • SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats. Fit for ALL kind of R/C Toys and also make electronics DIY based on compatible for Arduino ,Raspberry Pi.
  • The SG90 mini servo motor is lightweight, high-quality and lightning-fast.The servo is designed to work with almost all the radio control systems..
  • SG90 Micro Servo Motor compatible for Mini Arduino Servo SG90 9g Servo Kit for RC Helicopter Airplane Car Boat Robot Arm/Hand/Walking/Servo Door Lock Control with Cable.
  • The SG90 has 3 wire interfaces in which the connections should be made as follows: Red wire-5V, Brown Wire-Ground, Yellow wire-digital pin 9..
  • Stall Torque (4.8V): 17.5oz /in (1kg/cm).
Check Stock

AITRIP 3pcs for Arduino Mini Nano V3.0 ATmega328P 5V 16M Micro Controller Board Module with 3pcs USB Cable Compatible with Arduino IDE

  • *The Nano is using the chips ATmega328P and CH340, Replace FT232RL..
  • *It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper..
  • *Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
  • *The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source..
  • *Arduino Nano V3.0 ATMEGA328P Improved version with 3pcs pin headers (2pcs 15pin headers +1pcs 6pin headers)..
Check Stock

HiLetgo 3.5\ TFT LCD Display ILI9486/ILI9488 480x320 36 Pins for Arduino Mega2560

  • 3.5" TFT LCD Display ILI9486/ILI9488 480x320 Suitable for MEGA2560.
  • Support Arduino Mega2560 Directly inserted.
  • OnBorad level conversion chip for 5V/3.3V MCU.
  • Compatible with 3.3/5V operation voltage level.
  • Compatible with Arduino-Series development Board. (Please notice:This Screen is not touch screen).
Check Stock

Weewooday 6 Pieces Nano Board V3.0 ATmega328P Without Cable Compatible with Arduino Nano V3.0 with Pin Headers Pin Unsoldered

  • What you will get: the package included 6 pieces of nano board V3.0 ATmega328P, each nano V3.0 ATMEGA328P improved version with 3 pieces of pin headers unsoldered.
  • ATmega328P chips: using Atmega328P-AU MCU, support ISP download, using the same chips ATmega328P and CH340 with the official version.
  • Mini nano board: this is a portable, complete, and breadboard friendly board.
  • It has everything that compatible with Arduino has (electrically) with more analog input pins and onboard +5V AREF jumper.
  • Input and output: each of the 14 digital pins on the Nano can be applied as an input or output.
  • USB connection: the Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27).
  • The power source is automatically selected to the high voltage source.
Check Stock

Universal AC DC 5V 1A 2A/2000mA Power Supply Cord Adapter Charger with 8 Variable Plug Tips (Include 5.5mm / 3.5mm / Mini USB/Micro USB / 4.7mm Switching Connector)

  • 【Universal 10W Power Supply】AC input: 100-240V 50 60Hz.
  • DC Connector size: 5.5*2.1mm. (Can Fit for 5V 1A 1.5A 300ma 500ma 700ma 1000ma).
  • 【Widely Used DC 5V Power Cord】This 5V Charger Fit for Vizio sound bar, for Digitnow record player, for Polaroid record player, for Raspberry Pi, 5V Baby Monitor, Arduino/DIY Project, LED strip light, Webcam, HDMI products, Audio/Vedio, Android TV Box, LCD monitor, Kindle, Router, Photo frame, Bluetooth Speaker, Radio, IP/CCTV Security Camera, Tascam Recorder, USB HUB, DJ controller, Nextbook, Android Tablets, micro USB connectors for most smart phones and More 5V Device..
  • 【Get $5 worth of 8 connectors】This 5V 2A Power Cord offer More Selective with Micro-USB / 4.0*1.7mm / 3.5*1.35mm / 5.5*2.5mm / 3.0*1.1mm / 2.5*0.7mm / Mini-USB / LED Terminal Connector..
  • This 5 volt dc power supply offfer OverCurrent / OverVoltage / OverHeat / Short Circuit Protection..
  • 【Kindly note】If your device requires more than 2A (2000mah) then it will not be compatible. Only If your device requires less than 2A then it will work well and safely..
Check Stock

HiLetgo 3pcs ESP32 Mini ESP-WROOM-32 Development Board WLAN WiFi Bluetooth IoT Development Board

  • ESP32 Mini development board, everything needed to program the ESP32 module, ESP32/32S WIFI Development Bluetooth ESP8266 Module CP2104 for Arduino IDE..
Check Stock

ACEIRMC 3pcs Type-C USB CH340 5V 16MHz for Nano 3.0 ATmega328P Controller Board Compatible for Arduino Nano CH340 USB Driver Nano V3.0 ATmega328

  • for ARDUINO COMPATIBLE - Use the Nano-C with the for Arduino development IDE on your PC, Mac or Linux computer (USB driver installation required on some OSes).
  • PERFECT FOR BEGINNER OR EXPERT - Learn electronics and programming or jump start your latest project. Get started with the Nano-C in just minutes.
  • The Nano-C is breadboard-friendly and can be powered by USB, regulated 5V supply or unregulated 7-12V source. Connectors shipped unsoldered to fit the smallest of spaces.
  • Nano C for Arduino | USB Type-C Connector | ATmega328P | 5V | 16MHz | Without Cable | Connectors Unsoldered.
  • Uses the latest USB Type-C connector for compatibility with modern laptop and desktop computers. The Type-C connector is fully reversible which makes connecting a breeze.
Check Stock