Categories

Best Axis Io Module

12PCS Photosensitive Sensor Module Digital Light Intensity Detection for Electronic Practice DIY

  • Product Name: GY-271 QMC5883 L module (Triple Axis Compass Magnetometer Sensor Module/3 Axis Electronic Compass Module Magnetic Sensor Module/3 axis magnetic field module)..
  • Means of communication: IIC communication protocol.
  • High quality sink gold PCB, mechanical welding process, to ensure quality.The sensor converts any magnetic field to a differential voltage output on 3 axes..
  • Wide Application: GY-271 QMC5883L 3-Axis Magnetic Electronic Compass Module is small size of only 13 mm × 14 mm, it can be accommodated in small equipments such as drones reconnaissance aircraft and robot navigation system, mobile phone, laptop computer, car navigation system..
  • Package Includes: 2pcs * GY-271 QMC5883L Triple Axis Compass Magnetometer Sensor Module + 2pcs* Pin Strip..
Check Stock

2pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino Uno R3 Mega 2560 Nano Raspberry Pi 3 Smart Robotics Projects

  • HC-SR04 Ultrasonic Sensor Distance Module:using IO trigger for at least 10us high level signal..
  • The Module automatically sends eight 40 kHz and detect whether there is a pulse signal back..
  • If the signal back,through high level,time of high output IO duration is the time from sending ultrasonic to returning.Test distance = (high level time velocity of sound (340M/S)/2..
  • Resolution:0.3 cm,Module precision:blind spots (2cm)-SUPER CLOSE..
  • The module performance is stable,measure distance accurately.SRF05,SRF02 ultrasonic ranging module comparable.This module is compatible with GH-311 anti-theft module..
Check Stock

5pcs HC-SR04 Ultrasonic Sensor Distance Sensor with Ultrasonic Transmitter and Receiver Module Compatible with Ar-duino UNO MEGA2560 Nano Robot XBee ZigBee

  • Induction Angle: not more than 15 degrees:....
  • the module HC-SR04 works: (1) IO trigger ranging to at least 10us high signal.
  • (2) module automatically sends eight 40kHz square wave, automatically....
  • Panel wiring, VCC, trig 's (control side), the echo (receiving end), out (empty feet), GND.
  • Note: TRIP-pin internal pull-up 10K resistor, down TRIP microcontroller IO port pin, and then to a 10us pulse signal..
  • OUT pin for this module as the switch output pin when the anti-theft module, ranging modules do not use this foot!.
Check Stock

waveshare Original Raspberry Pi Compute Module 4 IO Board for All Variants of Compute Module 4,with Real-Time Clock Dual MIPI DSI/CSI Interfaces,USB Connectors

  • The Compute Module 4 IO Board is a companion board for all variants of Raspberry Pi Compute Module 4(supplied separately). It is designed for use both as a development system for Compute Module 4 and as an embedded board integrated into end products..
  • The Compute Module 4 IO Board is designed to allow you to create systems quickly using off-theshelf parts such as HATs and PCIe cards, which might include NVMe, SATA, networking, or USB. The major user connectors are located along one side to make enclosures simple..
  • Connectors: Standard Raspberry Pi HAT connectors with PoE support. Standard PCIe Gen 2 x1 socket. Various jumpers to disable specific features, e.g. wireless connectivity, EEPROM writing..
  • RTC : Real-time clock with battery socket and ability to wake Compute Module 4 Video: 2 x MIPI DSI display FPC connectors (22-pin 0.5 mm pitch cable) Camera: 2 x MIPI CSI-2 camera FPC connectors (22-pin 0.5 mm pitch cable).
  • USB: 2 x USB 2.0 connectors. Micro USB socket for updating Compute Module 4. Ethernet: Gigabit Ethernet RJ45 with PoE support..
Check Stock

LCD Touch Panels Touchpanel Analog For DOGS102 (EA TOUCH102-1)

  • 2.8 inch TFT LCD color screen, support 65K color display, and the display is colorful, high quality image display and wide viewing angle..
  • With PCB board (including power supply IC, touch IC, SD card cage) compatible 5110 interface. At least 4 IO driver are needed (without touch) , at least 9 IO driver are needed( with touch)..
  • This 2.8-inch LCD module uses ILI9341 drive chip to drive 240*320 dot , with 240*320 resolution..
  • On-board level translation programs truly perfectly compatible 5V / 3.3V IO level, supports a variety of single-chip IO connection, professional and practical..
  • We strive to provide you with the highest quality product and the best customer experience, if you're not entirely satisfied, please just feel free to contact us at any time..
Check Stock

Acogedor 2.8 Inch TFT SPI Serial Port LCD Touch Panel Module ILI9341 240x320 5V/3.3V (without touch)

  • ?2.8 inch color screen, support 65K color display, and the display is colorful.
  • ?With PCB board (including power supply IC, touch IC, SD cardcage) compatible 5110 interface.
  • ?At least 4 IO driver are needed (without touch) , at least 9 IO driver are needed( with touch).
  • ?This 2.8-inch LCD module uses ILI9341 drive chip to drive 240*320 dot , with 240*320 resolution.
  • ?The module is equipped with voltage stabilized IC to support 3.2v /5V power supply.
Check Stock

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock

LCD Display Module - 2.8 Inch TFT SPI Serial Port LCD Touch Panel Module ILI9341 240x320 5V/3.3V(带触摸最少9个IO驱动)

  • With PCB board (including power supply IC, touch IC, SD cardcage) compatible 5110 interface.
  • At least 4 IO driver are needed (without touch) , at least 9 IO driver are needed( with touch).
  • This 2.8-inch LCD module uses ILI9341 drive chip to drive 240*320 dot , with 240*320 resolution.
  • The module is equipped with voltage stabilized IC to support 3.2v /5V power supply.
  • 2.8 inch color screen, support 65K color display, and the display is colorful.
Check Stock

2 Pieces MPU-9250 GY-9250 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor I2C SPI 3-Axis Gyroscope Accelerometer Magnetometer Sensor Module

  • Basic information: module model: GY-9250.
  • Power supply: 3-5V (internal low dropout voltage regulator).
  • Communication: standard IIC communication protocol.
  • Internal structure: this module uses the MPU-9250, and combines a 3-axis gyroscope, a 3-axis accelerometer and a 3-axis magnetometer which are integrated into a single QFN package.
  • Reliable chip: the MPU-9250 integrates a 3-axis magnetometer AK8963, which features smaller size compared to previous generation and sensitivity improvement with 0.15 μT/ LSB.
  • The 16-bit AD converter is embedded in the chip, with 16-bit data output.
  • Quality process: the 9-axis sensor module features the immersion gold PCB, which uses the machine welding process to make it work fine.
  • Applications: DTV and set-top boxes are applied to internet connection.
  • Wearable sensors are applied to fitness equipment and sports.
Check Stock

ACEIRMC HC-SR04 Ultrasonic Sensor Distance Module for Nano Robot XBee ZigBee by ElecRight（5pcs

  • HC-SR04 Ultrasonic Sensor Distance Module: using IO trigger for at least 10us high level signal.
  • This module has stable performance and accurate measurement distance..
  • Detection distance: 0.78~196 in/ (2cm~500cm).
  • This module is fully Compatible with GH-311 anti-theft module..
  • HC-SR04 Ultrasonic Sensor Distance Module for Nano Robot XBee ZigBee by ElecRight.
Check Stock

SEEU. AGAIN 4pcs 8-Digit 7 Segment Module MAX7219 8 Bit Digital Segment Tube LED Display Module Supports Cascade Eight Bit Serial 3 IO Ports for MCU/51/AVR/STM32

  • MAX7219 is an integrated serial input / output common-cathode display driver, which connects your microprocessor to a 7-segment digital LED display with 8 digits.
  • MAX7219 digital display control module, you can use it..
  • The module is compatible of 5V / 3.3V microcontroller.
  • Only three IO ports are used to drive the eight digit display..
  • Only three IO ports are used to drive the eight digit display. MAX7219 supports flicker free displays as well as cascading displays.
  • PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen..
  • Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01.
  • Digital tube is 0.36 inch 4-bit integrated cathode digital tube.
  • Note:VCC and GND do not reversed, it would burn the chip.51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines..
Check Stock

SainSmart HC-SR04 Ranging Detector Mod Distance Sensor Blue

  • Using IO trigger for at least 10us high level signal.
  • The Module automatically sends eight 40 kHz and detect whether there is a pulse signal back.
  • IF the signal back, through high level ,time of high output IO duration is the time from sending ultrasonic to returning. Test distance = (high level....
  • Power supply :5V DC, quiescent current : .
Check Stock

Ili9341 LCD Display Module, ILI9341 5V/3.3V 2.8\ TFT SPI Serial Port LCD Touch Panel Display Module, 240x320[with Touch(9 IO Drive)](Without Touch)

  • ...er supply IC, touch IC, SD card cage) compatible 5110 interface. At least 4 IO driver are needed (without touch) , at least 9 IO driver are needed( with touch). 2.8 inch TFT LCD color screen, support 65K color display, and the display is colorful, high quality image display and wide viewing angle..
  • This 2.8-inch LCD module uses ILI9341 drive chip to drive 240*320 dot , with 240*320 resolution..
  • On-board level translation programs truly perfectly compatible 5V / 3.3V IO level, supports a variety of single-chip IO connection, professional and practical..
  • We strive to provide you with the highest quality product and the best customer experience, if you're not entirely satisfied, please just feel free to contact us at any time..
  • Buy it Confidence: Let you feel safe using, so you have a better using experience. Great value for money. If you have any problems, please fell free to contact us anytime. Our team will help you solve the problem as soon as possible..
Check Stock