Categories

Best Bearing Removal Tool

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

BESTOOL Gimbal Bearing Puller/Gimbal Bearing Installer tool, Boat Alpha, Bravo, Omc Gimbal Bearing Puller Remover, Engine Alignment General Tool for Heavy Duty Bearing Puller

  • DURABLE & STURDY:Our gimbal bearing puller is made premium material. The color is black and oxide finish on all the parts to it..
  • EASY REMOVAL:This gimbal bearing remover tool allows easy removal of the Gimbal bearing..
  • BLIND HOLE PULLER:The blind hole puller locks into the inner race of the bearing..
  • EASY TO USE:This gimbal bearing puller remover is easy to use, turn the end of the tool with a wrench..
  • WIDE APPLICATION:Our gimbal bearing puller fits for Mercruiser Alpha, Alpha 1, MR, Bravo's, OMC Cobra's, Volvo's..
Check Stock

Orion Motor Tech 3\ 4\ 6\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels (GD)

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes three puller sizes to cover most applications: a 3 inch gear puller with a 2.3" reach and 3" max. spread.
  • a 4 inch gear puller with a 3" reach and 4" max. spread.
  • and a 6 inch gear puller with a 4.7" reach and 6" max. spread..
  • Versatile Reversible Design: Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside as needed..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that these gear pullers are backed by Orion Motor Tech's warranty and friendly customer service..
Check Stock

Lidscura 8PCS Motorcycle Bearing Pullers 9-23mm Motorcycle Internal Bearing Removal Tool Kit Inner Bearing Extractor Kit

  • Widely Application: This Remover tool kit is ideal for internal bearing removal of automotive flywheel, motorcycle wheel, bicycle wheel, pump bearing generator bearing, machine bearing etc..
  • Meet Your Different Needs: Internal bearing Extractor tool set is equipped with 5 different sizes of open clips. The bearing can be disassembled from 0.35inch(9mm) to 0.91 inch(23mm) inside diameter..
  • Fine Workmanship: This motorcycle bearing pullers set is made of high-quality chrome vanadium steel, strong and durable for for a long service time..
  • Easy to Use: Connect this bearing puller kit with 1/2" 3/4" male thread water faucet, open clamps by turning handle clockwise to snug against the bearing for taking out the inner bearing..
  • Instructions for use: First the tool head into the inner ring of the bearing, and then screwed into the shaft, the tool head propped open hooked bearing inner ring, and then turn the shaft, you can pull out the bearing.
Check Stock

27213 Master Wheel Hub and Bearing Remover and Installer Tool Kit, Back and Front Wheel Bearing Puller Kit, Back and Front Wheel Hub Puller

  • 【WIDE COMPATINILITY 】-- Universal, provides various size of adapters makes installing wheel hubs and bearings on most domestics and foreign cars-rear, front, and four-wheel drive much easier. Compatible with BMW/Benz/Porsche/VW and most domestic/Asian/European vehicles. Works on Front, Rear and All-Wheel Drive Vehicles..
  • 【UPGRADE DESIGN】-- Designed with slide-hammer-free removal, make the job much simple that can easily install the hub and bearing changes on most cars. Under without the use of a hammer or a shop press, only use this tool be able to easily remove and install wheel hub and bearing assemblies as well as inner bearings. Whether it is a professional or DIY mechanic, can be easily, accurately and safely completed the disassembly and installation of the wheel hub and bearing on the vehicle..
  • 【SUPERIOR MATERIAL】-- Made of solid carbon steel with resisting impact and no deformation, surface black anodized anti-rust finish to anti-rust and anti-corrosion for years of trouble-free use. Mold-blown plastic case is convenience to carry and storage. Alternative to OEM 27213, quality and function meet to OEM. High precision and hardness, designed with o....
Check Stock

Orion Motor Tech 3\ 4\ 6\ 8\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes four puller sizes to cover most applications: a 3 inch gear puller with a 4.3" max. reach and 3" max. spread.
  • a 4 inch gear puller with a 5" max. reach and 4" max. spread.
  • a 6 inch gear puller with a 7.3" max. reach and 6" max. spread.
  • and an 8 inch gear puller with a 9.3" max. reach and 8" max. spread..
  • Versatile Design: Each of the three smaller 3-jaw gear and bearing pullers can be reversed to pull parts from the inside or outside.
  • the 8 in. puller can be used in 4 different positions to deal with both medium and large parts..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that th....
Check Stock

Powerbuilt Pilot Bearing Puller, Remove Bearings and Bushings, Foreign and Domestic Car Repair, Storage Case - 648619

  • Made to be the most reliable tools in the market today.
  • Tool set for removal of the pilot bearing and bushings from the flywheel during clutch replacement.
  • Heavy duty puller with 1 1/2-Inch fingers for an extra deep reach.
  • Kit 8 includes 1-Piece for removal of pilot bearing and bushings from the flywheel during clutch replacement.
Check Stock

DASBET 16PCS Blind Inner Bearing Puller Hole Remover Extractor Set Slide Hammer Tool Kit

  • 【Applicable】This inner bearing puller set is designed for loosening and pulling tight bearings and bushings, and fit for all vehicles 8-53MM bore bearing..
  • 【Instructions to operate】: How to use? Firstly insert the correct collet in the bore of the bearing and turn the nut to expand the collet till it is secure within the bearing.
  • Attach the small slide hammer and yank the weight towards the handle to give an extra snap of weight.
  • Repeat action until the bearing or bushing has been removed.
  • U-shaped bearing seal puller can be used by threading the bushing puller onto the collet and tightening the nut to slowly pull the bearing out of place..
  • 【Usage】This slide bearing removal tool is designed to quickly finish the job without damaging the removed parts or the tool. This small bearing puller tool is ideal for professionals and do-it-yourselfers..
  • 【Sturdy Construction】: Constructed of a strong, durable carbon steel, the bearing extractor tool is sure to pull even the toughest wheel bearing and bushings from tight positions. This blind bearing puller set has a long steel rod and a T-bar handle. The flared ends of the shop hammer weight provides a sturdy grip. The forged hardened steel and rust-proof finish help to increase pulling strength an....
Check Stock

Duncan Toys Yo-Tility Holster, Portable Yo-Yo Accessory

  • VERSATILE YO-YO ACCESSORY: Yo-yo on-the-go! The Duncan Yo-tility holster allows you to easily attaches your yo-yo to to belt loops, backpacks, and more..
  • BEARING REMOVAL TOOL: The Yo-tility holster has a built-in bearing removal tool so that you can easily change bearings anywhere you go..
  • BUILT-IN STRING CUTTER: The Yo-tility holster is equipped with a small string cutter for yo-yo string adjustments anytime, anywhere..
  • PRODUCT DETAILS: Includes [1] Yo-tility Yo-Yo Holster. Can be used with most yo-yos. Measures 6.5 in x 16 cm..
Check Stock

Bzsunway Front & Rear Bearing Puller Kit Wheel Hub Puller & Bearing Remover & Installer Kit Wheel Hub Remover & Installer Replace OEM 27213 (21pcs)

  • 【High Performance & Time Saving】  No need for other tools, no further calibration after disassembly and installation, the disassembly and installation of the wheel hub and bearing on the vehicle can be easily, accurately and safely completed, saving you more time and energy.
  • 【Wide Compatibility of Adapters】 Our wheel bearing puller/installer tools are specially equipped with suitable adapters for various models (like Volkswagen, BMW, Mercedes-Benz, etc).
  • 【Superior Quality】 Our wheel bearing removal tool set is made of high quality heavy duty stainless steel , durable and sturdy, and can hold up to the torque required to remove hubs and bearings. Ensure long-term use..
  • 【Must Have Tool Kit】 Use our wheel bearing stamping tools without need for a shop press. Whether it is a professional or DIY mechanic, our wheel bearing puller/installer can help you save more time. Tool Kit Use our wheel bearing stamping tools without need for a shop press, which is a must-have tool set for bearing disassembly.
  • 【Satisfactory Service】 If you are not satisfied with our products.You can request a full refund within 30 days to support a 12 month warranty.Professional and sincere service allows you to purchase without risk !.
Check Stock

YoYoFactory Wedge Yo-Yo - Polycarbonate - Evan Nagao Signature (Rayon Vert Green)

  • ...ecommend dual functional entry-level yo-yos. It is an excellent beginner kids yoyo, good for beginners to practise basic yoyo string tricks 1A 3A 5A, just a gentle tug on the string, it will return your hand easily..
  • Dual Purpose Yoyo - Also an Unresponsive YoyoResponsive yo-yo K2 is attached 8 balls unresponsive KK bearing. Once you're ready for unresponsive yoyo mode, the process to change it is very quick! All you have to do is grab the included yoyo bearing removal tool, the longer axel , and the concave bearing. You will get a new Unresponsive Yoyo, no need to buy another yo yo, a good value for you..
  • Premium Quality Plastic Yo-Yo MAGICYOYO K2 PLUS CRYSTAL Yoyo is made of high quality PC and beautiful crystal color, MAGICYOYO K2 CRYSTAL yo-yo is wear-resisting, durable and sturdy.
  • so its not easy to be damaged. This high quality plastic yoyo is an ideal gift for kids, friends, beginners, adults, family, as Christmas, Birthday gift..
  • Package Included1 x MAGICYOYO K2 PLUS CRYSTAL (Responsive Yoyo), Bonus - 5 x Yo-yo Strings (random color), 1 x Yo Yo Bag, 1 x bearing removal tool, 1 x KK Bearing ( For Unresponsive Use). Included everything you need for starting!.
  • IMPORTANT1.If the yo-yo do not come back sensitively, it is advised to drop few lubricatin....
Check Stock

ATP Blind Inner Bearing Puller Slide Hammer Set Hole Remover Extractor Set 5PCS

  • Premium Quality: The slide hammer puller set is constructed from drop forged steel with a fully chromed carbon steel slide hammer for maximum strength and longevity that resists rust and corrosion..
  • Specifications of The Bearing Puller Set: Overall length 15''/382mm, bearing extractor collets with internal capacity from 3/8"/10mm to 1-1/4"/32mm, bearing extractor 3/8"/10mm to 1/2"/14mm, 9/16"/15mm to 11/16"/19mm. 5/8"/18mm to 1"/25mm, 1"/25mm to 1-1/4"/32mm..
  • Great Function: Open clamps by turning handle clockwise to snug against the bearing, the blind bearing puller is great for pulling out evenly without damage the parts..
  • Wide Application: This pilot bearing removal tool blind hole bearing puller is ideal for pulling jobs,against the bearing for pulling out evenly without damage the parts, and perfect for professional and DIY use..
  • Storage Case: The slide hammer bearing puller is packed in a heavy-duty storage case with precision-sized compartments for every piece - great for storage and transport while lengthening....
Check Stock

Wheel Bearing Install/Removal Press Tool for Polaris RZR 900 1000 Turbo/Sportsman 1000 850 XP 550 / Scrambler 850 1000 / Ranger 1000 900 800 700 570 500 XP

  • BENIFITS - Using this installation and removal tool,Changing your wheel bearings become fast and correctly.
  • USAGE - This kit includes a holder for the rear hub and then a driver to press the old bearing out of the hub. After removal,flip over the hub and....
  • APPLICATION - Fits the following models and more using hub part number 5136689, 5136690 and wheel bearing part number 3514699 and 3514627:.
  • 2011-18 RZR 900 (All models, front and rear bearings) 2014-18 RZR 1000 (All models including Turbo, front and rear bearings).
  • INCLUDES - (1) Torpedo Installer Tool (1) Holder.
Check Stock