Categories

Best Broken Tap Extraction Tools

Walton 10124 #12, 4 Flute Tap Extractor With Square Shank

  • For helical coil wire screw thread insert taps.
  • Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure.
  • Threads per inch need not be specified as Tap Extractors will fit both NC and NF taps.
  • Hardened steel fingers of Walton Tap Extractors fit in the flutes of a broken tap to back it out simply and safely.
  • When fingers become bent or broken or are too short for further use, replacement fingers are available.
Check Stock

GripStick Headphone Plug Extraction Tool

  • PRODUCT COMPOSITION: This headphone extraction tool kit cutting has stainless steel pipes. These stainless tubes have different thicknesses, slits and cutting angles which can handle a variety of different repair situations. Applicable to all models of mobile phones, pads and computers with 3.5mm headphone jack..
  • 30 SECONDS EXTRACTION TOOL: You can use this headphone jack extraction tool to easily remove the broken headphone plug within 30 seconds. This headphone plug extraction tool will save you from spending 3 hours on a round trip to a professional repair store. Taking Care of Your Money! At least 100 bucks will be saved..
  • HOW TO USE: Use the short one first! Insert it into the headphone jack hole. Place the phone or pad upright and press the tube against the table. You'd better put a book underneath to prevent scars on the table. Gently downward to feel the extraction tool grab the broken headphone plug. Then tighten the end of the tube with hands or pliers and pull it out. If the broken plug is not all taken out, proceed with the long one headphone jack remover. Use the same method as above..
  • It is portable and can be used to disassemble glasses and watches and some other electronic products. Hope you like it!.
Check Stock

ABN Grease Fitting Tool - 4 Way Grease Fittings Tool Easy Out Zerk Fitting Tool for Damaged Grease Zerks and Fittings

  • SERVICE YOUR VEHICLE: Use the ABN 4-Way Grease Fitting Kit to install, remove, repair, and maintain zerk fittings in your vehicle, lawnmower, and other tools that use grease fittings.
  • This grease zerk tool kit even helps you remove damaged or broken grease fitting tabs.
  • 4 TOOLS IN ONE: Re-tap holes, install and remove fittings, and remove broken fittings with this four in one grease fitting removal tool.
  • Slotted grease fitting installation tool works with any straight, pin-type, or angled zerk including 30, 45, 65, and 90-degree angles.
  • FITS YOUR ZERK GREASE FITTINGS: Grease nozzle fitting greasing tool is suitable for 1/4 inch-28 and 6MM fittings, 1/4"-28 tap thread repairs, and 5/16-inch (7mm) and 3/8-inch (9mm) hex fitting and plug removals.
  • BUILT TO LAST: Constructed of heavy-duty metal ensures maximum strength and longevity.
  • 2-inch (5.1cm) T-design and a knurled body provides secure grip so you can install, rethread, or remove fittings easily.
  • EASY TO USE: Air grease gun accessories designed to clean out the threads of clogged fittings.
  • Grease zerk extractor grease fitting multi-tool features a built-in re-threader and extractor to help you remove worn and broken zerks and fittings.
Check Stock

NEIKO 04204A Hex Head Multi-Spline Screw and Bolt Extractor Set | 25 Piece Easy Out Screw Extraction | Broken Bolt remover | 1/8” to 7/8” in 1/32” Increment | Cr-Mo | Stripped Fastener Tool

  • For helical coil wire screw thread insert taps.
  • Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure.
  • Threads per inch need not be specified as Tap Extractors will fit both NC and NF taps.
  • Hardened steel fingers of Walton Tap Extractors fit in the flutes of a broken tap to back it out simply and safely.
  • When fingers become bent or broken or are too short for further use, replacement fingers are available.
Check Stock

Headphone Plug Extraction Tool - Headphone Jack Removal Tool, Tube Grip Stick Puller, Jack Remover - 4PC

  • PRODUCT COMPOSITION: This headphone extraction tool kit includes two short and two long laser cutting mini stainless steel pipe. These stainless tubes have different thicknesses, slits and cutting angles which can handle a variety of different repair situations. Applicable to all models of mobile phones, pads and computers with 3.5mm headphone jack..
  • 30 SECONDS EXTRACTION TOOL: You can use this headphone jack extraction tool to easily remove the broken headphone plug within 30 seconds. This headphone plug extraction tool will save you from spending 3 hours on a round trip to a professional repair store. Taking Care of Your Money! At least 20 bucks will be saved..
  • HOW TO USE: Use the short one first! Insert it into the headphone jack hole. Place the phone or pad upright and press the tube against the table. You'd better put a book underneath to prevent scars on the table. Rotate the tool when you can't press it in..
  • HOW TO USE: Gently downward to feel the extraction tool grab the broken headphone plug. Then tighten the end of the tube with hands or pliers and pull it out. If the broken plug is not all taken out, proceed with the long one headphone jack remover..
  • GUARANTEES: This set of headphone removal tool is considered a single-use tool. But we offer a....
Check Stock

BZBMGMO M11X1.5X28.2 Metric Thread Repair kit,10 Inserts

  • Standard M11 x 1.5 metric thread repair kit,Provided Insert length is 28.2mm.
  • Suitable for repairing M11 x 1.5 damaged threads on auto parts,Suitable for repairing damaged and worn M11X1.5 female threaded holes.
  • Repair tools that ordinary people can use, can be done with a power drill, pneumatic drill or by hand: drilling, tapping, inserts - anyone can.
  • Contrary to tooth misalignment and tooth extraction that often occurs with traditional threaded sleeves, this set of tools will not appear, and the CNC precision machined one-piece 304 stainless steel threaded sleeve is stronger and more durable than helical coils. Even a novice can easily do it in the shortest time.
  • Complete package includes: 1 Drill, 1 conterbore, 1 tap, 1 install driver, 10 inserts 28.2mm length.
Check Stock

Damaged Screw Extractor Kit, Stripped Screw Extractor Set, Drill Bit Set, Broken Bolt Extractor and Screw Remover Set,Made From H.S.S. 4341#, Set of 6 Pcs Stripped Screw Remover

  • ...WERFUL Stripped Screw Extractor ] : Striped Screw Works with Any Size Screw or Bolt Extractor Removes Even the Most Stubborn Stripped, Damaged, Embedded, Rusted and Painted-over Screws and Bolts.To Use The Grinding Head,The Screw Mouth Neets To Be Polished To A Sufficent Denth. The Greater The Depth, The Faster The Extraction Head Can Extract..
  • [WIDE VERSATILITY]:6 Piece Screw Extractor Set(#0, #1, #2, #2, #3, #4) Works with any Drill and any Size Screw or Bolt. Such as Common Hexagon Bolts, Lag Screws, Wood Screws, Hexagon Socket Screws, Machine Screws, Sheet Metal Screws and Other Screws, This Damaged Screw Extractor can Remove All Common Sizes of Damaged, Stripped or Broken Screws..
  • [HIGH QUALITY HSS 4341 AND TITANIUM PLATED] This Damaged Screw Removal Tool Kit Screw Extractor is Made of HSS 4341 High-Quality Speed, The Hardness is Up to 65 HRC, The Density And Hardness Are About 20% Higher Than The Ordinary Steel in The Market.
  • The Hardness is High, And it is Durable , Any Damaged Screws Can be Easily Removed. And We Plated a Layer of Titanium Extractor on it to Make it not Easy to Rust, Easier to Store, and More Beautiful..
  • [EASY OPERATION] A Damaged Screw Adapter can get the Job Done in Two Simple Steps , Choose a Bit Smaller Than the Damaged Scre....
Check Stock

AOYUTC Metal Tube Headphone Plug Extraction Tool- Headphone Tip Removal Tool,Remove Broken Headphone Plug from Headphone Jack of Mobile Devices

  • PRODUCT COMPOSITION: This headphone extraction tool kit includes two short and two long laser cutting mini stainless steel pipe. These stainless tubes....
  • 30 SECONDS EXTRACTION TOOL: You can use this headphone jack extraction tool to easily remove the broken headphone plug within 30 seconds. This....
  • HOW TO USE: Use the short one first! Insert it into the headphone jack hole. Place the phone or pad upright and press the tube against the table.....
  • HOW TO USE: Gently downward to feel the extraction tool grab the broken headphone plug. Then tighten the end of the tube with hands or pliers and pull....
  • GUARANTEES: This set of headphone removal tool is considered a single-use tool. But we offer a 100% satisfaction guarantee. If you are not satisfied....
Check Stock

Upgrated to Version 2.0 - Headphone Jack Removal Tool - Headphone Plug Extraction Tool, Tubes of Different Thickness, Jack Remover

  • PRODUCT COMPOSITION: This headphone extraction tool kit includes two short and two long laser cutting mini stainless steel pipe. These stainless tubes have different thicknesses, slits and cutting angles which can handle a variety of different repair situations. Applicable to all models of mobile phones, pads and computers with 3.5mm headphone jack..
  • 30 SECONDS EXTRACTION TOOL: You can use this headphone jack extraction tool to easily remove the broken headphone plug within 30 seconds. This headphone plug extraction tool will save you from spending 3 hours on a round trip to a professional repair store. Taking Care of Your Money! At least 20 bucks will be saved..
  • HOW TO USE: Use the short one first! Insert it into the headphone jack hole. Place the phone or pad upright and press the tube against the table. You'd better put a book underneath to prevent scars on the table. Gently downward to feel the extraction tool grab the broken headphone plug. Then tighten the end of the tube with hands or pliers and pull it out. If the broken plug is not all taken out, proceed with the long one headphone jack remover. Use the same method as above..
  • GUARANTEES: This set of headphone removal tool is considered a SINGLE-USE tool. But we offer a 100% satisfaction guarant....
Check Stock

JUYEER Headphone Plug Extraction Tool - Customized Metal Tube Grip Stick Puller, Headphone Tip Removal Tool with Headphone Hole Cleaning Brush

  • ✔️If this doesn't solve your problem, please feel free to contact us by email. You don't need to return the product, we can give you a full refund..
  • ✔️PURPOSE: JUYEER headphone plug extraction tool is built specifically to easily remove broken 3.5mm headphone plugs from jacks. It can be used on 3.5mm jacks found on phones, laptops and any other devices. You can solve your problem within 20 seconds..
  • ✔️HOW TO USE: Insert the steel tube between the headphone jack and a broken plug. You may need to lightly tap it in. It should go in about the same length as the headphone plug. Normally 0.55inch. Pinch with fingers or pliers for better grip. With broken plug enclosed, pull to remove..
  • ✔️GUARANTEES: This tool considered to be a single-use tool. But if you can’t solve your problem with this tool, you can take a picture and send that to us. And then you can get a full refund without a return..
  • ✔️Dear customers, the breakage of each earphone plug is different. We can't guarantee that this tool is suitable for all cases. Before you use this tool, please read the instructions carefully. Because the gap between the earphone plug and the earphone hole is very small, we have made the wall thickness of the tool as thin as we can. You need to plug....
Check Stock

OTC 6982PMC Professional Mechanics Collet Set for Removing Frozen or Correded Studs and Broken Bolts

  • OTC's Professional Mechanics Collet is designed to securely grasp broken studs with as little as 1/4 inch exposed, including corroded or frozen exhaust manifold studs.
  • Compact design lets this versatile tool get into tough to reach spots for extraction -in an around suspension and steering components, tight exhaust manifold clearances and more.
  • Designed to draw tight - within 1/16 inch of head surface to ensure a secure and stable attachment that greatly reduces tipping.
  • Kit includes 4 collets (6mm, 7mm, 8mm, 10mm) sized to fit common applications including exhaust manifold studs, broken head bolts, and other engine and chassis fasteners.
  • Durable blow-molded storage case keeps tools contained and organized so they are ready when you need them.
Check Stock

Damaged Screw Extractor Set for Broken Rusty Screw, Cool Gadgets Gifts for Men and Women, A HassleFree Broken Bolt Extractor and Screw Remover Set HSS M35 (70 HRC)

  • ...th our dynamic set of extractor drill bits, removing stripped, painted over, rusted or rounded screws & bolts has never been easier or more efficient !.
  • Easy to Use - Two easy steps, first you just need a drill, select a bit smaller than the damaged screw and begin the extraction by using the drill bit/burnishing tip and drill down to create a clean hole (make sure to run the drill in reverse during the process). Next use the drill bit to the extraction tip and using consistent, downward pressure (and a slow speed) allow the extraction tip to “bite” into the damaged screw, and then you can easily remove the screw..
  • Gifts for Men and Women, Holiday Gift Guide - This Damaged Screw Extractor makes an amazing gift for any occasion. A must-have stocking stuffer for men and women for Thanksgiving, Christmas, Mother's Day, wives, daughters, sons, kids, birthdays, tool gifts for dads, personalized Father's Day gifts for men, husbands, boyfriends, he, she, fathers, adults, stepfathers, teens, brothers, teenage boys, teenage girls, families, stepfathers. Practical funny gifts for men, cool stuff for men, cool tools for the man or women who has everything..
Check Stock

Walton 10253 1/4\

  • LONG SERVICE TIME---The tap extractor 3/4 flute is made of superior high speed steel, which is of high hardness and anti-corrosion, could be used for quite a long period.
  • 3/4 FLUTE SPECIFICATION---1#: 3 flute, M4, 6#.
  • SUITABLE FOR---The tap extractor 3/4 flute works for removing stripped, rusted, broken, or corroded screws and bolts, Suitable for industrial screw and bolt removal and for everyday home repair work.
  • SPECIFICALLY ENGINEERED---With each tap extractor specifically engineered, the tap extractor 3/4 flute could grab speedily, and could grab broken screw taps out easily.
  • QUALITY GUARANTEEING---Every tap extractor gets through rigorous quality testing, and unqualified one will be removed, durable to use. Please feel free when using.
Check Stock