Best Cam Lock Fire Hose Fittings

Dixon G400-C-AL Aluminum A380 Global Type C Cam and Groove Hose Fitting 4 Socket x 4 Hose ID Barbed

Straight body with two openings for connecting two hoses or pipes with cam and groove fittings.
One female cam coupler end for connecting to male groove adapters and one hose shank end for connecting to hoses (Type C).
Aluminum for resisting corrosion and tarnishing.
Cam lock levers for locking the fitting's male groove adapter into female cam couplers.
Nitrile butadiene rubber seal rated for petroleum service, ethanol to E100, and biodiesel to B20.

Check Stock

AGHITG Lightweight Backwash Hose 1-1/2' ID x 30 FT, Fire Hose Reinforced Lay Flat Sump Pump Hose for Swimming Pool Discharge

Packaging - Package includes an outdoor hose of 1.5 inches (inside diameter) x 30 feet (length). In addition, there also comes with accessories (include two 304 stainless steel wire clamps and a non-woven storage bag as a gift). The stainless steel wire clamps will help you connect Cam Groove Hose Fittings Male and Female, or Short Suction Coupling Set Aluminum Hose Fitting..
After-sales support - We are here to make sure you are 100% satisfied. If you encounter problems during use, please be sure to contact us, we will promptly respond and provide a perfect solution..

Check Stock

Keg Disconnect Ball Lock MFL Ball Lock Fittings Keg Connectors – Keg Coupler Stainless Ball Lock Keg Fittings 12-Piece

...TE BEVERAGES: Use the G. Francis Ball Lock Keg Fitting Ball Locks 12-Piece Ball Lock Quick Disconnect Set with Liquid & Gas Disconnects, Swivel Nuts, & Hose Clamps to ferment and dispense craft cocktails, soda, and other beverages from your existing keg.
USE YOUR KEG: Each of the ball lock keg connectors (fittings) have an approximate 2.2-inch height and 1.3-inch outside diameter (5.6cm x 3.3cm) and is compatible with ball lock Cornelius (Corny) kegs and keg couple adapters for homebrewing.
Hose clamps have 0.2-inch to 0.5-inch (6-12mm) diameter while the barbed swivel nuts have 5/16-inch outside diameter (OD) fitted for 1/4-inch or 3/16-inch inside diameter (ID) hoses on your 3, 5, or 10 gallon keg.
BUILT TO LAST: Keg ball lock quick disconnects and hose clamp wings constructed from ABS plastic that resists rust and corrosion.
Swivel nuts and clamps constructed from food-grade stainless steel for maximum strength and longevity.
INSTALL EASILY: Tighten the swivel nut connecting the flare fitting before use.
Ensure correct fittings are installed on input and output posts – Light gray disconnect for gas inlet and black disconnect for fluid outlet.
To install fittings, pull up lever on ball lock disconn....

Check Stock

Fire Hydrant Adapter, 2-1/2\ NST (NH) Female x 2\ NPT Male Brass Fire Hose Hydrant Adapter with Pin Lug Fire Equipment Fitting Nipple for Fire Hydrants, Hoses, Pipes

【Size】Brass fire hydrant adapters with 2-1/2" National Standard Thread (NST) female on one end for connecting to the hydrant and a 2’’ NPT male on the other end for connecting to a hose. Perfect for attaching to fire hydrant..
【Material】Brass fire hydrant fitting is made of brass for corrosion resistance, ductility at high temperature and low magnetic permeability, they are more heat-resistant than aluminum rigid fire hose and hydrant adapters..
【Easy Operation】Brass fire hose adapter with pin type lugs for quick connect and disconnect, easy to use. These fittings will not rotate as a hose is moved, making them less likely to loosen or break than swivel adapters..
【Application】Brass fire adapter fittings used for connecting fire hose, pvc pipe and other low pressure pipes in the fire brigade, industry, refinery, building industry, agriculture, shipping, military and civil protection..
【Quality Warranty】We did 100% inspection before these brass fire hydrant adapter leave our factory, if you have any problem with these products after you receive them, please feel free to contact us, we will give you a solution..

Check Stock

Accoladesound 30PCS Furniture Cam Lock Nut Connectors Fittings, 15MM Fittings for Cabinet Drawer Dresser and Wardrobe Panel Connecting, Silver

30-PACK CAM LOCK NUT CONNECTORS FITTINGS——Material: Zinc Alloy, Anti-corrosion.
Surface Treatment: Nickel Plating. Fit for various types of furniture, cabinet, drawer dresser..
CAM CONNECTOR SIZE——Diameter (Approx.):15mm / 0.6″.
Inner Height(Approx.): 3mm / 0.12″.Easy to install, thicken material..
HOW TO USE——One of the three in one component, which needs to be used together with dowel pin and pre-inserted nut..
APPLICATION WIDE——Cam Fittings fit for various types of furniture, cabinet, drawer dresser, wardrobe and furniture panel. (Please check the size before buying).
YOU WILL GET——30Pcs Furniture Cam Fittings, solid and durable, not easy to twist off, long service life.

Check Stock

MSCRP Fuel Injection Line Fitting Adapter Kit EFI FI w/Filter/Regulator LS Conversion

1Pc 6AN 25 feet of high-pressure fuel injection hose.
1Pc 6AN to 3/8" Male Straight Filter Fittings+1Pc 6AN to 5/16" Fuel Filter Return Line Fitting.
2Pcs 6AN to 3/8" Fuel Filter Feed Line Fittings+2Pcs -6AN to 1/4" NPT Fuel Pump Adapters+2Pcs 45 Degree -6AN Female to 3/8" Push Lock hose fittings.
6Pcs straight -6AN Female to 3/8" Push Lock hose fittings.

Check Stock

PneumaticPlus RED EPDM synthetic Rubber Air & Water Hose 1/4\ ID x 0.53\ OD with 1/4\ NPT Male Fitting Connections (6 FT)

...ype E Connector is installed on both ends of hose by stainless steel clamps, high pressure, sturdy and durable, abrasion resistance, anti-aging, chemical resistance, you can use for a long time..
003c/b003e[SIZE]:003c/b003e Backwash pump hose, standard 3 inch diameter, Flat width 4.85 inch.
3 in Aluminum cam lock fittings type C, type E and extra TYPE A adapter. Length: 50 feet.
Temperature Range: 23°F to 149°F (-5°C to 65°C).
003c/b003e[NO LEAK]:003c/b003e Pool Backwash hose doesn’t leak or burst within 90 psi working pressure. Because the delivery hose body adopts fine double-sided coating and fiber reinforcement. The camlock coupling shank is special multi-section structure and added black rubber ring and sealant at the connection..
003c/b003e[WIDELY USED]:003c/b003e Ideal for draining swimming pools, backwash pool filter, sewage pump, sump pump, trash pump, pool drain and sand filter pumps etc.
widely used in household, mine, factory, agriculture, and architectural engineering.
This drain hose can adapt to most outdoor conditions and all seasons..
003c/b003e[EASILY USE]:003c/b003e It can be easily connected, after Type A is connected to the pump, just slide type A male adapter into type C female coupler, press the b....

Check Stock

D-WEIXIN 2' × 50' Pool Backwash Hose, Heavy Duty Reinforced Blue PVC Lay Flat Water Discharge Hoses for Drain Pools and Clean Filters

The pool backwash hose is made of PVC and reinforced with polyester yarn, can withstand 90 psi working pressure during water supply and drainage, heavy-duty, superior strength, economical, durable, leak-free and weather, chemical and burst resistant..
Backwash hose is standard 2 inch hose, flat 3.4’’ wide, fit 2’’ standard size filter outlet or cam lock / pin lug fittings, and fit 1.5’’ or less size schedule 40/80 PVC pipe. Be sure to measure your filter outlet to ensure proper fit before ordering..
The discharge hose is essential swimming pool supplies, works as pool drain hose, pool pump hose, filter waste hose, also works for agricultural water discharge, irrigation, landscaping, construction dewatering and submersible pumping..
The pool hose is made to fit standard connections to backwash pool filtration systems , and you can easily install it with clamp. After use, just roll it up and hardly take up any space, and then store it in a dry place for next use, away from direct sunlight..
Unlike traditional paper-thin single layer hose, it can be used multiple times and withstand rough handling. If you want a drain hose that will last, this is what you are looking for!.

Check Stock

EVIL ENERGY 6AN to 3/8 Barb Push Lock Hose End Fitting 45 Degree Blue&Red 2PCS

6AN female swivel to 3/8 barb fitting 45 Degree.
Please attention that AN6 push lock fitting only be worked with rubber fuel line. It can not be installed on PTFE Hose, Nylon Braided Hose, or....
Thread Size of 6an 45 Degree push lock fitting is 9/16-18UNF and the rubber fuel line which works with should be 3/8"..
Push on locking fittings are much more easier on installation than swivel and PTFE fittings. (high-pressure system not recommended).
EVIL ENERGY Provide plenty kind of fuel fittings, Swivel, Push-on lock, PTFE hose end and other fitting adapters..

Check Stock

DAVCO 2' x 100 ft Pool Backwash Hose, Heavy Duty Reinforced Blue PVC Lay Flat Water Discharge Pump Hoses For Swimming Drain Pools and Clean Filters,with 1 Clamp

The pool backwash hose is made of PVC and reinforced with polyester yarn, can withstand 90 psi working pressure during water supply and drainage, heavy-duty, superior strength, economical, durable, leak-free and weather, chemical, and burst resistant..
Backwash hose is standard 2 inch hose, flat 3.4’’ wide, fit 2’’ standard size filter outlet or cam lock / pin lug fittings, and fit 1.5’’ or less size schedule 40/80 PVC pipe. Be sure to measure your filter outlet to ensure proper fit before ordering..
The discharge hose is essential swimming pool supplies, works as pool drain hose, pool pump hose, filter waste hose, also works for agricultural water discharge, irrigation, landscaping, construction dewatering and submersible pumping..
The pool hose is made to fit standard connections to backwash pool filtration systems , and you can easily install it with clamp. After use, just roll it up and hardly take up any space, and then store it in a dry place for next use, away from direct sunlight..
Unlike traditional paper-thin single layer pool backwash hose, it can be used multiple times and withstand rough handling. If you want a drain hose that will last, this is what you are looking for!.

Check Stock

Draft Brewer New 5 Gallon Stainless Steel Ball Lock Keg

【MFL QUICK DISCONNECT】MRbrew threaded beer cornelius keg ball lock disconnect fittings come with MFL swivel nuts, make hose changing and extra equipment adding a breeze, allow more options of extra functions and possibilities for your kegging system!.
【BUY ACCESSORIES SEPARATELY? NO!】MRbrew ball lock fittings comes with complete sealing and hose connection parts, 5/16” barb for connecting gray disconnect to gas hose, 1/4” barb for connecting black disconnect to liquid hose, clamps guarantee no leak on connection!.
【YOUR LONG-LASTING USE CHOICE】MRbrew ball lock fitting set is made of stable PBT material, it has strong oil resistance, its smooth surface makes cleaning easy. Stainless steel has strong corrosion resistance, not easy to get rust. MRbrew makes your beer brewing more economy!.
【POWERFUL APPLICATION KIT YOU NEED】MRbrew ball lock keg fitting is perfect for most Cornelius Keg, Pepsi Keg and 7-UP tanks, also can be a home brewing adapter of Corny & Keg coupler, suitable for beer, soda, and other beverages dispensing!.
【100% LIFELONG ISSUES SOLVING FOR YOU】Each MRbrew ball lock keg fitting set is backed by unbeatable, reliable, trusted product quality, we will unconditionally solve your problems if you are not satisfied!.

Check Stock

EXCELFU LP Propane Gas Fire Pit Stainless Steel Burner Ring Installation Kit, 12 inch

Fire Pit Burner Ring: 12 inch round fire ring with 1/2 inch female gas inlet, rated for up to 150,000 BTUs. Made of durable #304 stainless steel for maximum rust resistance and long lifespan..
Stylish Design: New cross-bar design for better gas distribution and made your fire pit enjoyable..
Safety&Secure Connection: Fiber reinforced propane hose with solid brass fittings for corrosion resistance, ductility at high temperatures and prodive airtight sealing..
Easy Installation: CSA Certified 5 feet connect hose and 5 feet propane hose with type-1 (QCC-1) propane tank connections. Long extension hose meet your needs for fire pit installation..
Buy with Confidence: Every propane fire pit kit is backed by 18-month warranty. If you are not satisfied with your purchase, just contact with us and our Customer Service Team will help you..

Check Stock

F-AL-3/8, 3/8″ Threaded Female Tank Filter for Mosquito Misting Systems

{Made in USA Pump & Tubing} Mid Pressure Patio Misting Kit complete with 200PSI Booster Pump, Cleanable Brass/Stainless Steel Misting Nozzles, UV treated flexible tubing, and push lock fittings. Easy to install..
{Pump Specifications} 110 Volt Kit Includes: – 200PSI Booster Pump with Plug (110v) – 50ft Flexible Tubing – Calcium Inhibitor Filter – 12 Brass/Stainless Steel Mist Orifice Nozzles – 0.012” – 11 – Push Lock Mist Tees – 1 – Push Lock End Mist Elbow – 6ft Feed line with 3/4 Garden hose connector – Plastic Clamps.
{Installation} – Push Lock Fittings – Easy Connect -Whisper Quiet Operation Easy to hook with any garden hose Max Water pressure 200 PSI Supports up to 20 Nozzles Wall Mountable Plugs in to standard 115V outlet (wall plug included on 110v models only).
{Comes with Filter to protect your Nozzles} Booster Pump Features: Built-In Thermal Safety Switch Supports up to 20 Nozzles 110v AC 1.2 Amps 0.50GPM Wall Plug (on 110v pumps only) Inlet Fitting: 3/4” Garden Hose Connecter Outlet Fitting: 1/4” and/or 3/8” Push Lock.
{Easy to Expand} Booster Pump Features: Supports up to 20 Nozzles 110v AC 1.2 Amps 0.50GPM Wall Plug (on 110v pumps only) Inlet Fitting: 3/4” Garden Hose Connecter Outlet Fitting: 1/4” and/o....

Check Stock