Categories

Best Camera For Octoprint

MELIFE for Raspberry Pi 4 Camera Day & Night Vision Camera Adjustable-Focus Module 5MP OV5647 Sensor Webcam Video 1080p with 2 Infrared IR LED Light HD Webcam for Raspberry pi 3 B+/3B/2B/4B

  • All-day Image: it's built-in ir-cut camera, automatically switches day and night mode for better and clearer image. This can avoid image color cast, which is easier for beginners to use,Adjustable is for focus..
  • Widely Used: Supports connecting infrared LED and/or fill flash LED. This Camera Night Vision Camera also support to for RPi 4 3B/3B/RPi 2B B+..
  • 5 Megapixel: For RPi camera module uses the dedicated CSI interface, via the CSI bus, A higher bandwidth Link which carries 5 megapixels data from the camera back to the processor..
  • 1080P HD Webcam: The IR video Camera is support of 2592 x 1944 pixel static images, and supports 1080 P @ 30 FPS, 720 P @ 60 FPS and support octoprint 640 x480 P 60/90 video Recording, with 5MP Ov5647 1080P webcam sensor..
  • Attention: Normal problems: 1.The computer doesn't recognize the camera.
  • The LED lights doesn't work (including one on and one off).
  • The camera doesn't work after a period of use. Solution: Tighten the bolts of the LED and camera, then restart it. 2.The LED lights always turn on no matter if the camera is turned on or not. Solution: Connect the power supply to GPIO, then the LED light will be on only when the camera is turned on..
Check Stock

8 Pieces Camera Compatible with Raspberry Pi Module with 15 Pin Ribbon Cable and Flex Extension Cable Set Compatible with Raspberry Pi Model A B B+, Pi 2 and Raspberry Pi 3, 3 B+, Pi 4

  • ...a practical design for you to take some beautiful photos of your family.
  • Flex extension cable set: whatever for 3D printer, home security, or other for raspberry pi camera project, this camera cable set can totally meet your requirement.
  • Compatible with all Raspberry Pi board, camera module and display, suitable for octoprint 3D printing monitoring.
  • Wide compatibility: this 5 megapixels camera module is compatible with raspberry pi model A or B, B+, model 2, raspberry pi 3, 3 B+, pi 4, works well with your equipment, bring you high-definition images for raspberry pi is suitable for aerial photography, car real-time photography, indoor and outdoor photography, video recording, travel vlog and so on.
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Black ABS 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Black ABS 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • ABS Filament Specs: Black - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Print Temperature: 240°C - 260°C (464°F - 500°F)/ Print Bed Temperature: 80°C - 110°C (176°F - 230°F).
  • Why INLAND ABS Filament: Designed with the high quality and compatibility in mind, Inland ABS Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience), USB power supply, USB cables, webcam feed(optional).
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm White ABS 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm White ABS 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • ABS Filament Specs: White - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Print Temperature: 240°C - 260°C (464°F - 500°F)/ Print Bed Temperature: 80°C - 110°C (176°F - 230°F).
  • Why INLAND ABS Filament: Designed with the high quality and compatibility in mind, Inland ABS Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience), USB power supply, USB cables, webcam feed(optional).
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Blue ABS 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Blue ABS 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • ABS Filament Specs: Blue - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Print Temperature: 240°C - 260°C (464°F - 500°F)/ Print Bed Temperature: 80°C - 110°C (176°F - 230°F).
  • Why INLAND ABS Filament: Designed with the high quality and compatibility in mind, Inland ABS Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience), USB power supply, USB cables, webcam feed(optional).
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Pink PLA 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Pink PLA 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA Filament Specs: Pink - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 215°C - 230°C (419°F - 446°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F) Spool Diameter: 8.81 in. (223.77 mm) - Spool Width: 2.81 in. (71.37 mm) - Spool Hub Hole Diameter: 2.00 in. (50.80 mm).
  • Why INLAND PLA Filament: Designed with the high quality and compatibility in mind, Inland PLA Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience),....
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Silver PLA 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Silver PLA 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA Filament Specs: Silver - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 215°C - 230°C (419°F - 446°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F) Spool Diameter: 8.81 in. (223.77 mm) - Spool Width: 2.81 in. (71.37 mm) - Spool Hub Hole Diameter: 2.00 in. (50.80 mm).
  • Why INLAND PLA Filament: Designed with the high quality and compatibility in mind, Inland PLA Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experien....
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm White PLA 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm White PLA 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA Filament Specs: White - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 215°C - 230°C (419°F - 446°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F) Spool Diameter: 8.81 in. (223.77 mm) - Spool Width: 2.81 in. (71.37 mm) - Spool Hub Hole Diameter: 2.00 in. (50.80 mm).
  • Why INLAND PLA Filament: Designed with the high quality and compatibility in mind, Inland PLA Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience....
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Red PLA 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Red PLA 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA Filament Specs: Red - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 215°C - 230°C (419°F - 446°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F) Spool Diameter: 8.81 in. (223.77 mm) - Spool Width: 2.81 in. (71.37 mm) - Spool Hub Hole Diameter: 2.00 in. (50.80 mm).
  • Why INLAND PLA Filament: Designed with the high quality and compatibility in mind, Inland PLA Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience), U....
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Marble PLA 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Marble PLA 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA Filament Specs: Marble - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 215°C - 230°C (419°F - 446°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F) Spool Diameter: 8.81 in. (223.77 mm) - Spool Width: 2.81 in. (71.37 mm) - Spool Hub Hole Diameter: 2.00 in. (50.80 mm).
  • Why INLAND PLA Filament: Designed with the high quality and compatibility in mind, Inland PLA Filament undergoes numerous testing procedures to help you spend less time troubleshooting and more time printing. Your filament will arrive dried and vacuum sealed with desiccant to ensure a high-quality smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experien....
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Olive Green PLA PRO (PLA+) 3D Printer Filament Bundle

  • A 3D Printer accessories combo - 1.75mm Olive Green PLA PRO (PLA+) 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA PRO Filament Specs: Olive Green - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 205°C - 225°C (401°F - 437°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F) Spool Diameter: 8.81 in. (223.77 mm) - Spool Width: 2.81 in. (71.37 mm) - Spool Hub Hole Diameter: 2.00 in. (50.80 mm).
  • Why INLAND PLA PRO Filament: Designed with the highest quality and compatibility in mind, Inland PLA+ Filament undergoes numerous testing procedures to ensure that you spend less time troubleshooting and more time printing! Your filament will arrive completely dry and vacuum sealed with desiccant to ensure a high-quality, smooth print.
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Black PLA PRO (PLA+) 3D Printer Filament Refill Bundle

  • A 3D Printer accessories combo - 1.75mm Black PLA PRO (PLA+) 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA PRO Refill Filament Specs: Black - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 210°C - 225°C (410°F - 437°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F).
  • Use less plastic with PLA RPO Refill: PLA+ Filament is non-toxic and comes without a spool. PLA+ is less brittle than standard PLA, improving your prints' toughness and layer adherence. We also offer the Inland Reusable Spool that perfectly fits this refill! Use less plastic and use the same Spool with every new filament refill..
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience), USB power supply, USB cables, webcam feed(optional).
Check Stock

OctoPrint 3D Printer Remote Control Webserver System Pre-Flash Card and Inland 1.75mm Blue PLA PRO (PLA+) 3D Printer Filament Refill Bundle

  • A 3D Printer accessories combo - 1.75mm Blue PLA PRO (PLA+) 3D Printer Filament bundle with OctoPrint 3D Printer System Pre-flashed 32GB Micro SD Card.
  • PLA PRO Refill Filament Specs: Blue - 1 KG / 2.20 lbs per spool - 1.75mm diameter (+/- 0.03mm). Recommended Extrusion/Nozzle Temperature: 210°C - 225°C (410°F - 437°F) Recommended Bed Temperature: 60°C -80°C (140°F - 176°F).
  • Use less plastic with PLA RPO Refill: PLA+ Filament is non-toxic and comes without a spool. PLA+ is less brittle than standard PLA, improving your prints' toughness and layer adherence. We also offer the Inland Reusable Spool that perfectly fits this refill! Use less plastic and use the same Spool with every new filament refill..
  • OctoPrint is a snappy webserver that runs on a Raspberry Pi and lets you remote-control a 3D printer from your computer. Control and monitor your 3D printer from your phone or other web-capable device. Easily stop, start, or pause your 3D prints from anywhere.
  • Compatible with most of the available consumer 3D printers and its powerful plugin system allows extending its functionality in various ways. Setup hardware: Any Raspberry Pi (Pi 3 and up for the best experience), USB power supply, USB cables, webcam feed(optional).
Check Stock