Categories

Best Contractor Table Saw

Delta 36-5152T2 Contractor Table Saw with 52\ Rip Capacity and Cast Extension Wings

  • IF ANY COMPONENT IS MISSING FROM YOUR ORDER PLEASE ACCEPT THE SHIPMENT AND CONTACT AMAZON. DO NOT RETURN THE ENTIRE UNIT BECAUSE OF A MISSING PART. WE WILL EXPIDITE THE DELIVERY OF ANY MISSING COMPONENT. THANK YOU.
  • THIS ITEM SHIPS IN 3 BOXES. YOU SHOULD RECEIVE THE FOLLOWING COMPONENTS - 36-5 Saw Body 36-T52 52" Rails 36-T53 Extension Table.
  • Powerful 15 amp Contractor Grade motor easily handles hardwoods.
  • 52 Inch Rip Capacity handles large stock.
  • Legendary Biesmeyer Fence Accurate to 1/64”.
  • Smooth and dependable adjustable belt drive table saw.
  • Cast iron table top with 2 cast iron extension wings.
  • Heavy duty one piece rail system for precision cuts every time.
Check Stock

Coleman Cable 02569 12/3 Hi-Visibility Low-Temperature Outdoor Extension Cord 100-Foot

  • High visibility blue low-temperature vinyl jacket, resists oil, grease, and moisture.
  • 3-conductor, 12-gauge wire, 15-amp rating.
  • Contractor grade circular saw, heater, and table saw.
  • Power indicator light lets you know where the power is.
Check Stock

SawStop MB-CNS-000 Contractor Saw Mobile Base

  • Fully-welded 1/4″ rigid steel construction.
  • Supports entire table for all Contractor Saw table lengths.
Check Stock

Southwire 2568SW0006 50ft 12/3 SJTW Premium High Visibility Low Temp Cord Blue, 50 ft

  • High visibility blue low-temperature vinyl jacket, resists oil, grease,moisture.
  • 3-conductor, 12-gauge wire, 15-amp rating.
  • Contractor grade, circular saw, heater, table saw.
  • Power indicator light lets you know where the power is 12 GAUGE HEAVY DUTY, 50 ft..
Check Stock

Delta 36-5000T2 Contractor Table Saw with 30\ Rip Capacity and Steel Extension Wings

  • IF ANY COMPONENT IS MISSING FROM YOUR ORDER PLEASE ACCEPT THE SHIPMENT AND CONTACT AMAZON. DO NOT RETURN THE ENTIRE UNIT BECAUSE OF A MISSING PART. WE WILL EXPIDITE THE DELIVERY OF ANY MISSING COMPONENT. THANK YOU.
  • THIS ITEM SHIPS IN 2 BOXES. YOU SHOULD RECEIVE THE FOLLOWING COMPONENTS - 36-5000 Tables Saw Body 36-T31 30" Rails.
  • Powerful 15 amp Contractor Grade motor easily handles hardwoods.
  • 30 Inch Rip Capacity handles large stock and 13/16 in. X 8 in. STACKED DADO CAPACITY.
  • Legendary Biesmeyer Fence Accurate to 1/64”.
  • Smooth and dependable adjustable belt drive table saw.
  • Cast iron table top with 2 stamped steel extension wings.
  • Heavy duty one piece rail system for precision cuts every time.
Check Stock

Delta 36-725T2 Contractor Table Saw with 30 Rip Capacity and Steel Extension Wing

  • Powerful 1. 75 Hp Contractor Grade motor easily handles hardwoods.
  • 30 Inch Rip Capacity handles large stock and 13/16 in. X 8 in. STACKED DADO CAPACITY.
  • Smooth and dependable adjustable belt drive table saw.
  • Cast iron table top with 2 stamped steel extension wing.
  • Heavy duty rail system for precision cuts every time.
Check Stock

The Original Dubby Cut-Off • Cross Cut Sled for Cutting Precise Accurate Miters with a Table Saw (Left Side Dubby Sled)

  • ...an extremely safe way to cut small pieces, and will easily pivot out of the way when you don’t need it. With 35lbs. of hold down pressure, the clamp will hold small pieces all the while keeping your hands and fingers out of harms way..
  • WILL THE DUBBY FIT YOUR SAW? The Dubby sled is compatible with most cabinet and contractor table saws. However, your table saw should fall within the following specs for a proper fit. The Miter Slot should be a ¾” wide x 3/8” deep slot. Your saw must measure at least 27” from the front of the saw to the back. The miter slot must be 4” to 5 ¾” from the installed table saw blade. PLEASE NOTE: that the Dubby WILL NOT work on most JOBSITE style table saws. Please measure your saw before ordering..
Check Stock

The Original Dubby Cut-Off • Cross Cut Sled for Cutting Precise Accurate Miters with a Table Saw (Left Side Dubby and Right Side Dubby Sleds are Included)

  • ...an extremely safe way to cut small pieces, and will easily pivot out of the way when you don’t need it. With 35lbs. of hold down pressure, the clamp will hold small pieces all the while keeping your hands and fingers out of harms way..
  • WILL THE DUBBY FIT YOUR SAW? The Dubby sled is compatible with most cabinet and contractor table saws. However, your table saw should fall within the following specs for a proper fit. The Miter Slot should be a ¾” wide x 3/8” deep slot. Your saw must measure at least 27” from the front of the saw to the back. The miter slot must be 4” to 5 ¾” from the installed table saw blade. PLEASE NOTE: that the Dubby WILL NOT work on most JOBSITE style table saws. Please measure your saw before ordering..
Check Stock

Fulton 110V Single Phase On/Off Switch with Large Stop Sign Paddle for Easy Visibility and Contact for Quick Power Downs Ideal for Router Tables Table Saws and Other Small Machinery

  • We have all been in a situation where we need to quickly turn the power off on our router table or contractor table saw and both of our hands are a bit pre-occupied. Reaching down and underneath your router table or contractor table saw to try and locate the power switch can be very cumbersome as well as very dangerous while your feeding stock through.Many router table setups don’t even have an external power switch separate from the router itself..
  • With this uniquely designed and easy to locate Paddle Button Stop Power Tool Switch you can simply bump the large stop sign paddle with your knee or hip to shut the power off. That means both of your hands can stay engaged on the project while you bump the power off with your hip or knee. A large green START button is always visible on the top side of the paddle. Simply push the START button to power on..
  • Install the switch near or at hip level or in a position that you will be able to bump it when needed. The switch comes with installation hardware and can be mounted to most any type of material. The unit has two cords. The heavy duty female cord is 18” long and designed to accept the power source plug from your power tool. The heavy duty male cord is approximately 66 inches long and is used to pl....
Check Stock

POWERTEC 71142 Universal Table Saw Miter Gauge Assembly/Miter Gauge with 27 Angle Stops

  • FUNCTION: A high performance woodworking angle tool that possesses a miter guide which mounts into the miter slots of your table saw (band saws and other applications) and then guides the miter gauge parallel to the blade for high precision angled and crosscuts.
  • FEATURES: A lightweight design with a durable laser-cut aluminum construction, large gauge handle, universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted and non T-slotted miter slots, and adjustable expansion discs that remove all side play from the bar, creating a perfect fit..
  • PRECISION: Angle guide with 27 total locking stops in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts.
  • UNIVERSAL DESIGN: Works with most Contractor style, full sized saws, or tools with standard miter slots (3/4” width x 3/8” depth) with or without T-slots, making it compatible with popular brand table saws, band saws, router tables, disk and belt sanders. PLEASE NOTE : will not work with smaller saws or tool with 5/8” miter slots..
Check Stock

The Original Dubby Cut-Off • Cross Cut Sled for Cutting Precise Accurate Miters with a Table Saw Right Side Dubby Sled

  • THE ORIGINAL DUBBY SLED From standard 4 sided panel cutting to the absolutely stunning heptagon frame you will be completely accurate with the angles....
  • WORKING WITH LARGE PANELS The Dubby has the capacity to crosscut panels up to 24″ wide x 52″ long, and allows you to do them safely. Since the....
  • WORKING WITH ANGLES The Dubby angle scale is the simplest, most accurate and easiest to read scale available. Being about 15-20 times more accurate....
  • WORKING WITH SMALL PIECES- No miter gauge on the market can offer you the margin of safety provided by the Dubby Sled. The versatile hold-down clamp....
  • WILL THE DUBBY FIT YOUR SAW? The Dubby sled is compatible with most cabinet and contractor table saws. However, your table saw should fall within the....
Check Stock

Vega PRO 50 Table Saw Fence System 42-Inch Fence Bar 50-Inch to Right

  • Uses existing hole pattern for Delta Unisaw, Contractor, powermatic 66, Sears 10-inch saw.
  • Fence mounting system allows full adjustment for accuracy.
  • Guide rails supported by brackets, 2-1/2-inch fence height.
Check Stock

E. Emerson Tool Co. CXW-36 36-Inch Extra Wide All-In-One Contractor Straight Edge Clamping Tool Guide w/Story Stick

  • Straight Edge - E. Emerson’s Contractor Series self-clamping straight edge patented design has integral tubes running the length of the wide body construction, making it ultra rigid and light to handle..
  • No C-clamping - No more C-clamping! Achieve that truly straight cut using this self-clamping straight edge to guide your tools..
  • Extra Wide - This self clamping straight edge is extra wide for exceptional rigidity and has a low profile for obstruction-free cuts..
  • Flat Top - The extra low profile and flat top makes it easier for all circular saw or router straight cuts..
  • Contractor Series - Please note: recessed tracks accept Contractor Series Saw Plate, Router Plate, and Stop Block. But it will not work with A, Twin, or Ultra Series accessories..
Check Stock