Categories

Best Control 12v Dc Motor

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

  • DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
  • STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
  • FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
  • PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
  • UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..
Check Stock

Riorand DC 3V 6V 12V 24V 35V 5A Motor Speed Controller PWM Speed Control Ultra Small LED Dimmer（2PCS）

  • Speed Control Switch Low Voltage DC 3V 5V 6V 12V 5A.
  • Motor Speed Controller with a self-recovery fuse 5A and a Power-On LED light.
  • Provide a continuous current of 5A to your DC brush motor or other DC load.
  • This mini controller will be disconnected automatically if the current is too large and the fuse will recover automatically after cooling.
  • Please just contact me by email if there are any issue and I will solve it within 24 hours.
Check Stock

Mini Electric Motor 30W Permanent Magnet DC Motor 12V/24V High Speed CW/CCW (DC 24V 6000RPM)

  • Permanent magnet dc motor high speed with long output shaft,easy to install..
  • DC 12V 3000RPM or DC 24V 6000RPM,2 size for your choice..
  • The stator windings of the motor are copper wire, low heat, low loss, long life,and with CW/CCW control..
  • Widely used in cotton candy machine, small cutting bench, grinding machine, medical equipment and other mechanical equipment..
  • Mini Size- Motor body (Diameter x Height) 5.1cm/2 inch x 7.1cm/2.8 inch..
Check Stock

8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot

  • Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
  • The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
  • Terminal driver part of the supply area VMS: +5V ~ +35V.
  • Drive part of the peak current Io: 2A / Bridge.
  • Logical part of the terminal power supply range Vss :4.5-5 .5V.
  • Logical part of the operating current range: 0 ~ 36mA.
  • The control signal input voltage range: 4.5-5.5V low 0V high.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
  • High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..
Check Stock

Liftmaster LA400PKGU Dual Swing Gate Opener Kit, Battery Backup, Receiver & Photocell, Gate Sensor Included!

  • Powerful Gate Opener: Motor Voltage: DC 24V.
  • The powerful actuator is made of steel and IP44 level protection for outdoor use. Pass tests of CE & ETL. Note: You need to purchase 2 of 12V batteries for use. (NOT INCLUDED).
  • Remote Controller: The electric gate opener is equipped with a remote controller(Control Distance: 65-98 ft). You can drive in the car and control the gate opening or closing with the RC. It will auto close the gate after the 60s without any operation. Keep home safe for you..
  • Push/Pull-to-open Install: Our single swing gate opener is compatible with two-way door installation: push-to-open & pull-to-open. Perfect for all gate types includes chain link, tube, panel, vinyl, and wood. It is designed for gates up to 11.8 ft long and 308 lbs/leaf..
  • Protections & Indicator: This gate opener has a flashing red light for indication, and warning placards on both sides of the door. Open the door with a release key when powering out..
  • Diverse Use Places: Perfect for home, yard, farm, factory, company, villa, community, agricultural, farm, ranch, etc. Note: A DC 24V battery or 2pcs of DC 12V batteries(not included) are required to power the gate opener..
Check Stock

Low Voltage Dc 1.8v 3v 5v 6v 12v 2a Motor Speed Controller PWM 2PCS

  • Speed Control Switch Low Voltage DC 1.8V 3V 5V 6V 12V 2A.
  • Motor Speed Controller with a self-recovery fuse 2A and a Power-On LED light.
  • Provide a continuous current of 2A to your DC brush motor or other DC load.
  • This mini controller will be disconnected automatically if the current is too large and the fuse will recover automatically after cooling.
  • Please just send us an email if there is any issue and we will solve it within 24 hours.
Check Stock

DC Motor Speed Controller Universal DC 12V 24V 10A Electronic Stepless Speed Regulator Switch for Car Truck Fan Heater Control

  • 【Universal】Voltage 12V or 24V. Overload current: 10A. Supports high power, 12V/120W, 24V/240W.
  • 【Features】Easy to adjust and control speed of DC motor, simple wiring and convenient to use, a great replacement for broken one. Extra long knob screw to meet installation needs.
  • 【Wiring】Red wire connected to the positive pole of power supply and motor, blue wire connected to the negative pole of motor, black wire connected to the negative pole of power supply.
  • 【Heat dissipation】This electronic stepless speed controller is a upgraded fan heater controller with heat sink that will ensures a better heat dissipation.
  • 【Application】Widely used for 12-24V DC electric appliances. Adjust motor speed, automobile fan heater control, defroster, fans speed regulation, etc.
Check Stock

Fencia DC Motor Speed Control PWM Controller 10V-50V 5000W MAX 100A + Pedal Accelerator

  • ⭐ Larger current, max current up to 100A, continuous operating current of up to 60A. Power requirement: DC 10-50V, frequency: 15khz, control motor power: 0.01-5000w..
  • ⭐ Reversing control motor, dual relay control, can withstand higher current. Programmable to meet subsequent extensions..
  • ⭐ With soft start to reduce the shock of large current when the motor starting. With brake when the power off or change the rotation of the motor..
  • ⭐ Quiescent current: 0.04a, regulation range: 0-100%, size: 145*78*38mm/5.7*3.07*1.49in..
Check Stock

Tnuocke 12V/24V DC Motor Speed Controller Universal,Knob Screw Electronic Stepless Speed Regulator Switch,Adjustable Motor Speed, Automobile Fan HeaterControl, Defroster, Fans Speed Regulation

  • 【About DC motor】Voltage 12V or 24V. Overload current: 10A. Supports high power, 12V/120W, 24V/240W.
  • 【High quality】This electronic stepless speed controller is a controller with heat sink that will ensures a better heat dissipation.Easy to adjust and control speed of DC motor,knob screw convenient to use.
  • 【Product size】length 86.8mm/3.42in,wide 32mm/1.27in,high 35mm/1.39,wire length is 120mm/4.7in.
  • 【Way of connection】Red wire connected to the positive pole of power supply and motor, blue wire connected to the negative pole of motor, black wire connected to the negative pole of power supply.
  • 【Wide use】Widely used for adjust motor speed, automobile fan heater control, defroster, fans speed regulation, etc..
Check Stock

CHANCS TYC-50 Synchronous Motor 12V DC 5-6RPM CW/CCW 4W Electric Gear Motor For Christmas Decorations

  • Model : TYC-50； Shaft Diameter: 7mm ； Shaft Length: 16mm； Direction : CCW/CW(uncontrollable)； Voltage : DC 12V； Speed : 5-6RPM； Power :....
  • This is a TYC-50 DC 12V 5-6RPM synchronous motor,small power consumption, low noise, small size, light weight, easy to use. The reduction gear is....
  • Widely used in hand-made, school project, electric fan shake heads, heaters, Christmas tree, prayer cylinders, air conditioners, microwave ovens, glue....
  • Motor shaft, line length, speed, voltage can be designed according to customer requirements. If you need other models of motor, you can contact us.....
  • Attention: The applicable voltage of this motor is DC 12V, using AC power supply, the motor does NOT work.
  • too high voltage will burn the motor.If you....
Check Stock

Concentric 1 HP 115/208-230 Volt AC Hydraulic Power Unit - Basic, Model Number 1530036

  • the flow rate is 2 GPM, and it is a double-acting pump for both power up and power down..
  • Easy to Use: This 12V hydraulic power unit has been fully assembled in advance. The wiring is simple and comes with operating instructions. Two additional SAE#6 connectors and one 15 ft remote control are included in the package..
  • Reliable Quality: The dump trailer pump is made of sturdy metal.
  • thus, the oil tank is not easy to crack or be damaged. As a power unit, this is a perfect replacement pump for remote hydraulic systems. Equipped with an overflow valve, it automatically releases when overpressure, safer and reliable..
  • Rapid Start: With its powerful motor, this hydraulic electric pump is quick to start and quick to output oil.
  • it can provide strong power for hydraulic systems like dump trailers, dump beds and is able to complete lifting in a short time..
  • Wide Application: This power unit is widely used in stackers, small, and medium-sized lifting platforms. It is compatible with many dump trailers and movers and is a direct replacement for 12V DC remotely controlled hydraulic systems..
Check Stock

Bonvoisin 30T Hydraulic Cylinder Jack Porta Power Ram 2\ Stroke Mini Single Acting Lifting Cylinders for Machinery Shipbuilding

  • ...port (SAE#6) is 3200 PSI, and on B port (SAE#6) is 1500 PSI.
  • the flow rate is 2 GPM, and it is a double-acting pump for both power up and power down..
  • Easy to Use: This 12V hydraulic power unit has been fully assembled in advance. The wiring is simple and comes with operating instructions. It includes a 15 ft remote control and two additional SAE#6 connectors are provided for replacement..
  • Reliable Quality: The dump trailer pump is made of sturdy metal.
  • thus, the oil tank is not easy to crack or be damaged. As a power unit, this is a perfect replacement pump for remote hydraulic systems. Equipped with a relief valve, it avoids overpressure, safer and reliable..
  • Rapid Start: With its powerful motor, this hydraulic electric pump is quick to start and quick to output oil.
  • it can provide strong power for hydraulic systems like dump trailers, dump beds and is able to complete lifting in a short time..
  • Wide Application: This power unit is widely used in stackers, small, and medium-sized lifting platforms. It is compatible with many dump trailers and movers and is a direct replacement for 12V DC remotely controlled hydraulic systems..
Check Stock

12V Fan Controller, DROK DC Motor Speed Controller for Brush Motor 7V-60V 20A 420W PWM Driver Board Control 12V 24V 36V 48V Regulator Cooling Fan Dimmer Governor Pulse Width Modulator with Adjust Knob

  • Parameters --- Applicable voltage range: DC 7V-DC 60V, 60V is the highest operating voltage, please leave a margin for application. Control power: 12V within 200W.
  • Aluminum Shell --- Prevents the controller from easily damaged.
  • The holes in its sides and bottom makes it easier to be installed..
  • Stable Performance and Small Heating --- With the good materials of FR4 double panels, reasonable circuit management and fuse, the modulator works quite excellent..
  • LED Indicator and Power Supply Control --- The board equips with red LED power supply indicator which will light on when the module is power on. You can turn off power supply output by screwing the potentiometer..
  • NOTE --- 1. This product is a DC brushed motor speed controller. It needs to be equipped with a DC power supply to power the governor. It cannot be connected to AC power and cannot drive the brushless motor. 2. Before powering on the wiring, please read the wiring label, the positive and negative poles of input cannot be mistaken. The output connection to the motor does not need to be positive or negative. But if the direction of rotation is wrong, please change the two wires of the motor..
Check Stock