Best Counter Shaft
3pcs/Pack Brass Mini Ball Valve Shut Off Switch 1/4" NPT Male x 1/4 INCH NPT Female Rated to 600WOG for Water Air Compressor Etc
- BRAND NEW TRUE 5HP COMPRESSOR DUTY MOTOR, 56HZ FRAME, 3450RPM, 7/8" SHAFT DIAMETER.
- 22 FULL LOAD AMP AT 230V, THIS MOTOR NOT SUITED FOR INCOMING VOLTAGE LESS THAN 208V.
- CCW (COUNTER CLOCKWISE) SHAFT ROTATION WHEN VIEWED FROM THE SHAFT END. SHAFT ROTATION IN NOT REVERSIBLE.
- 2.25" SHAFT LENGTH, KEYED SHAFT, 60HZ, 1.0 SERVICE FACTOR.
- WIRING INFO SHOWN ON NAMEPLATE, PROFESSIONAL INSTALLATION REQUIRED.
Check StockAll Balls Racing 25-4001 Counter Shaft Seal Kit
- Meets or Exceeds OEM Specs for Fit and Performance.
- Compatible With/Replacement For: Husaberg 390FE 2010-2011, 450FE 2009-2011, 450FX 2010-2011, 570FE 2009-2011, 570FS 2010-2011, FE250 2013, FE350 2013-2014, FE450 2014, FE501 2013-2014, Husqvarna FC 250 (EURO) 2015, FC 250 2014-2019, FC 350 2014-2019, FC 450 (EURO) 2015, FC 450 2014-2019, FC 450 Rockstar Edition 2018, FE 250 2014-2019, FE 350 2014-2019, FE 350S 2015-2016, FE 450 2014-2019, FE 501 2014-2019, FE 501S 2015-2016, FS 450 2018, FX 350 2017-2019, FX 450 2018-2019, TC 125 2014-2015.
- 1-year warranty protects you after your purchase. We're confident that our products will work flawlessly once installed in your vehicle. In the rare case that it does not, we'll replace it anytime within one year of your order. If you have a problem, we will take every step to assist you. Contact us for a replacement..
- 100% New aftermarket Counter Shaft Seal Kit built to meet OEM specifications.
Check StockHydraulic Gear Pump Sizes from 0 to 18 gpm 3625psi SAE A Flange Side Ports CCW-Rotation, PFEG Series (Shaft: 3/4\ Diameter keyed, 12cc: 9gpm at max. RPM)
- IMPORTANT: SHAFT MUST ROTATE COUNTER CLOCKWISE WHEN LOOKING AT THE SHAFT. IMPROPER ROTATION DIRECTION COULD LEAD TO SHAFT LEAKAGE AND SEAL FAILURE..
Check StockCody James Men's Stockman Cowboy Boot Broad Square Toe Brown
- Premium Full-Grain Leather Foot And Shaft.
Check StockDixon Valve GL347 2 1/2\ Face 0-400 PSI Lower Mount Gauge, (Box of 10)
- Application in textiles, machinery, winding hill, printing, large stamping, conveyor packaging.
- 5 digit pull counter is used to accumulate the number of times of the recording instrument or mechanical reciprocating movement.
- Connect the auxiliary shaft of the counter pulls the arm to instrument or machine for pulling counting.
- The digital display directly, with a rotating return to zero device. After returning to zero, it can start counting from zero.
- Easy to operate, and count accurately, is practical counter tool..
Check StockFlagg-Air 340HT-J Septic Aerator – Jet Replacement
- Economical and reliable replacement comparable to Jet Aerator. 12" mounting bracket designed to fit 10" tank riser opening..
- Motor is fully enclosed - Rated for continuous duty - Oversized, pre-lubricated and sealed bearings.
- High quality stainless steel shaft - Corrosion resistant bronze counter shaft.
- Meets or exceeds all specifications of the OEM product.
Check Stock5 HP 3450 RPM, 56 Frame, 230V, 22Amp, 7/8\ Shaft, Single Phase NEMA Air Compressor Motor - EM-05
- Single phase, Full Load amps: 22Amp, 230V.
- Frame Type: 56HZ, 7/8" Keyed shaft, Shaft length:2 3/8".
- NEMA Motor is Non-Reversible CCW (Counter Clockwise) ONLY.
Check Stock2 HP SPL 3450 RPM, 56 Frame, 120/240V, 15/7.5Amp 5/8\ Shaft, Single Phase NEMA Air Compressor Motor - EM-02
- Single phase Full Load amps: 15/7.5Amp, 120/240V.
- Frame Type:56, 5/8" Keyed shaft, Shaft length:2 1/16".
- NEMA Motor is Non-Reversible CCW (Counter Clockwise) ONLY.
Check StockNEW 2 HP SPL Compressor Duty Electric Motor, 3450 RPM, 56 Frame, 5/8\ Shaft Diameter,120/240 VOLT
- 2 HP SPL COMPRESSOR DUTY ELECTRIC MOTOR, ODP (OPEN DRIP PROOF) FOR DRY INDOOR ENVIRONMENTS.
- 1 PHASE, 56 FRAME, 3450 RPM, 120V/240VAC, 5/8" SHAFT DIAMETER.
- CAPACITOR START AND CAPACITOR RUN CONTINUOUS DUTY COMPRESSOR MOTOR.
- Amperage: (7.5 FLA @ 240V) (15 FLA AT 120V), Voltage: 120V/240V (NOT SUITED FOR 208V INCOMING).
- CCW (COUNTER CLOCKWISE ROTATION) WHEN VIEWED FROM SHAFT END. MODEL: 56S34D2M EMZ BRAND AND EMZ INDUSTRIES INC.
Check StockBlender Replacement Parts for Magic Bullet, Compatible with 250W Magic Bullet Blender (MB gear)
- ⚙️ [COMPATIBLE MODEL] The replacement accessories for Magic Bullet is ONLY compatible with 250W Magic Bullet Blender (MB1001 Series), Does NOT fit Mini Magic Bullet or Baby Bullet..
- ️ [EASY TO INSTALL] 1. Take a towel, with a towel wrap blade with his left hand holding.2. Right hand holding the connecting shaft, connecting shaft rotate clockwise to fall.3. When installing counter-clockwise to tighten..
- [PACKAGE INCLUDE] 2 Blender Base Gears + 2 Blender Blade Gears + 4 Gaskets. Without any risk shopping with us. If you have any question, we will help you within 24 hours..
Check StockBase Gear for Magic Bullet Blender MB1001 250W Blade Gear Replacement Part
- PACKAGE INCLUDE: 2 plastic gears for the Motor base and 4 rubber gears for under the blade. Blade is NOT included..
- MODEL NUMBER:Base gear replacement for Magic Bullet MB1001 (120V,Max 250W,60HZ).
- Size:30mm diameter whole piece and approximately 4mm diameter internal screw hole.
- GOOD REPLACEMENT:This is non-original aftermarket part,but It is made exactly fit for Magic Bullet.
- EASY TO INSTALL: 1. Take a towel, with a towel wrap blade with his left hand holding.2. Right hand holding the connecting shaft, connecting shaft rotate clockwise to fall.3. When installing counter clockwise to tighten..
Check StockPyle Desktop Microphone Stand - Universal Tabletop Mic Holder w/ Flexible 8.2'' Inch Gooseneck Mount and Solid U Shape Base - Perfect for Table Desk or Counter - PMKS8
- ADJUSTABLE GOOSENECK: The Pyle desktop microphone stand is 8.2” inches high. It does not create static noise during adjustment. Quite and effortless mic adjustment comes with a universal microphone holder or clip attachment..
- VERSATILE POSITIONING: This ideal mic stand with a flexible and bendable shaft is perfect for table, desk, counter and the like. Also, the gooseneck shaft gives you the ability to position your microphone smoothly in all directions you desired..
- STURDY U SHAPE BASE STAND: With it's solid die casting iron U shape base in 5.6'' x 6.8'' dimension, Pyle mic stand will provide stability and precise balance to avoid it from falling. And, 2.02 lbs counterweight for a stable microphone placement..
- CONVENIENT BENDABLE TUBE DESIGN: This is an ideal professional mic stand for table, desk and counter. It is simple with durable design for long term use and lightweight makes it easy to transport from show to show or home to home..
- WORKS PERFECTLY: Perfect mic positioning and optimal pickup for in studio or on stage performances. The Pyle PMKS8 is a class at its own gooseneck mount..
Check StockTOOLACC Base Gear for Magic Bullet Blender MB1001 250W Blade Gear Replacement Part
- PACKAGE INCLUDE: 2 plastic gears for the Motor base and 4 rubber gears for under the blade. Blade is NOT included..
- MODEL NUMBER:Base gear replacement for Magic Bullet MB1001 (120V,Max 250W,60HZ).
- Size:30mm diameter whole piece and approximately 4mm diameter internal screw hole.
- GOOD REPLACEMENT:This is non-original aftermarket part,but It is made exactly fit for Magic Bullet.
- EASY TO INSTALL: 1. Take a towel, with a towel wrap blade with his left hand holding.2. Right hand holding the connecting shaft, connecting shaft rotate clockwise to fall.3. When installing counter clockwise to tighten..
Check Stock