Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger
- This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
- Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
- These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
- Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
- And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
- Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check StockTwo Position Low V Actuator w/End Switch
- Output: fan relay, alarm relay and 4-20ma current loop.
- Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
- Mounts on a standard 4” x 4” electrical box.
- 5 a spdt fan relay controls starters of exhaust fans.
Check StockAoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger
- This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
- Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
- These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
- Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
- And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
- Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check StockSainSmart 8-Channel Relay Module
- 5V 8-Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A.
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP432, TTL logic).
- Indication LED's for Relay output status.
Check StockYoungneer 5v Relay Board Raspberry Arduino Relay Module 1 Channel Opto-Isolated High or Low Level Trigger
- 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
- 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
- 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
- 【Wide Application】- These 5v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
- 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check StockDPST 1NO 1NC 8Amp Power Relay Module, Briidea 24V AC/DC Power Relay Control Voltage, White
- INPUT CONTROL SIGNAL: Voltage AC or DC 24V, Current 17mA..
- OUTPUT CURRENT: Output switch DPST 1NO 1NC(Double Pole Single Throw, 1 Normally Open and 1 Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
- SIMPLE & PRACTICAL: This passive power relay module is simple and practical, which is very convenient to use. It can support both Normally Open and Normally Close..
- EASY MOUNT: The power relay is of compact plastic case and wires connects for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
- LED INDICATION: This power relay has a led indicator for relay action indication. It is obvious to know the status of the switch at a glance..
Check StockELEGOO 8 Channel DC 5V Relay Module with Optocoupler Compatible with Arduino UNO R3 MEGA 1280 DSP ARM PIC AVR STM32 Raspberry Pi
- 5V 8-Channel Relay interface board, each one needs 70mA Driver Current.
- Equiped with high-current relay, AC250V 10A.
- Each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
- With power indicator,8-way road has a status indicator. With a relay coil to absorb the diode protection..
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- The 8 channels are optically isolated, safe, reliable, anti-interference. Widely used for all MCU control, industrial sector, PLC control, smart home control。For a complete data sheet for this relay board, please download it from: http://dwz.win/UhW.
Check StockVeris,Current Switch and SPST Relay,N.O H735
- The Hawkeye Relay Combination Series is the ideal solution for the automation installer..
- These units combine a current switch and relay into a single package, reducing the space required for total control of fans and pumps..
- The current switch and relay operate independently of one another..
- These devices allow start/stop control and status monitoring with one device instead of two..
Check StockSainSmart 16-Channel 12V Relay Module Board for Arduino DSP AVR PIC ARM
- 12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A.
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
- Indication LED's for Relay output status.
Check StockSSR-100, DC-DC Solid State Relay 5-220V DC with Non-Contact Switch, SSR-100 DD
- Control Method: The solid state relay uses DC-DC control method, which can provide stable performance..
- Load Current: 100A, Load Voltage: 5-220VDC, Control Voltage: 3-32VDC, Control Current: DC: 5-50mA.
- Installation: The solid state relay uses bolted installation method, easy to install and remove..
- Heat Dissipation: The relay has pure aluminum heat sink base plate for fast heat dissipation..
- Material: The solid state relay is made of thyristor and optoelectronic with non-contact switch..
Check StockMacurco TX-12-HS White Hydrogen Sulfide H2S (Line Voltage) Fixed Gas Detector Controller Transducer with White Housing
- Output: fan relay, alarm relay and 4-20ma current loop.
- Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
- Mounts on a standard 4” x 4” electrical box.
- 5 a spdt fan relay controls starters of exhaust fans.
Check StockARTGEAR Automotive Relays for Car Truck Motor Boat Car Starter - 12V DC 120 Amp Split Charge Relay Switch with 2 Pin Footprint + 2 Terminal
- 【Continuous Relay】 You can use it as continuous relay, if the relay keeps working for 5 hours, it would be better to stop it and then use it again . It could pass continuous 50A~60A current.
- 【Package Contains】 1 x Heavy Duty Split Charge 120A ON/OFF Relay.
- 【Large Capacity】 Up to 120A coil capacity able to handle those high current applications with ease, Heavy duty make or break (on/off) relay.
- 【Long service life】 Life Expectancy Electrical: 100,000 Operations (at 30 Operations/min) Life Expectancy Mechanical: 10,000,000 Operations, keep a high level in ongoing work.
- 【Applicable】 High Power automotive relays provide standard contact form, and has the standard 4 pin layout, fit of starter kills, dome light supervision, trunk release, polarity change, power door lock/actuator control etc.
Check StockValefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10
- 【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
- 【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
- 【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
- 【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
- 【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
Check Stock