Kiro&Seeu L293D DC Motor Drive Shield Stepper Motor Drive Shield Expansion Board Compatible with Arduino Duemilanove Raspberry Pi
- This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip..
- Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel..
- Tested compatible for Arduino Mega, Diecimila & Duemilanove..
- 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter..
- Multi-function, easy to operate, a strong driver library support and feature updates..
Check Stock
DC 5V 12V 18V 24V 5A 150W PWM Motor Speed Controller, Mini Speed Control Switch, Speed Regulator with Stepless Variable Rotary Knob - for Electric Motor, Brush Motor, Car, Generator, Fan (DC 5-30V)
- Wide voltage range - DC 5-30V PWM motor speed controller switch, rated output current 5A, maximum output current 15A, max power 150W.
- Settable duty cycle, duty cycle upper and lower limits and working frequency - set up these 3 parameters according your own motors.
- comes with start and stop button and can be controlled by external switch.
- High percision digital encoder knob - can adjust the motor speed , more accurate and consistent than ordinary potentiometer, easy to match the value.
- Soft-start protection - the current increases slowly when starting the motor, avoid the high shock current, effectively protect the motor and extend its service life.
- Widely applications - good to control the output of power, brightness, speed.
- perfect for DC drive motor, generator, LED lights, light bulbs, lamp, car, fan, micro-pumps, solenoid valves, micro-pumps, solenoid valves.
- (Note: This product can only be used for DC brushed motors, not for brushless motors).
Check Stock
Trolling Motor Plug Receptacle Set, Briidea Marine Boat DC Power Connector Waterproof for Freshwater and Saltwater 12,24,36,48V
- A MUST HAVE FOR TROLLING MOTORS: This plug and receptacle set is suitable for marine trolling motors. The design of self-locking can connect trolling motor and power supply firmly, effectively preventing the plug from accidentally falling off. It has high performance to ensure easy boating and uses high-quality materials to ensure safety. Includes plug and receptacle..
- PREMUIM QUALITY: Corrosion-resistant, brass gold-plated electrical components. The shell has IP67 waterproof performance, flame retardant performance and high temperature resistance, which can achieve reliable connection in any freshwater or saltwater application. Its weatherproof feature makes it durable, providing continuous service for you..
- RELIABLE & CONVENIENT: The receptacle contains a watertight sealing cap and a gasket to further strengthen the waterproof performance, and guarantees fastening effect to prevent vibration. This set adopts direct insertion self-locking structure with an ergonomically contoured handle with strong grip. The plug lock ring has a conspicuous unlocking prompt, which is convenient for unlocking. Saves time and effort..
Check StockTE CONNECTIVITY / POTTER & BRUMFIELD T92P7D22-12 POWER RELAY, 12VDC, 30A, DPST-NO, FLANGE
- Electromagnetic relays are widely used: household air conditioner compressor motors, fan motors, cooling pump motors, starter relays for car starters, spur relays, motors, generator circuit breakers, industrial relays, etc.
- Product Name: Electromagnetic Power Relay.
- Red mechanical indicatoe:It can intuitively judge whether the relay is attracted.
- LED signal lamp : It can judge the AC or DC coil, and judge whether the coil is energized.
Check StockEiechip® CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver 3D Printer Interface & Driver Modules
- 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module..
- The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers..
- It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors..
- Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors..
- This shield can make quick work for managing stepper motors in your project..
Check StockPWM Pulse Generator, DROK Dual Mode Adjustable Function Generator DC 3.3-30V 1-150kHZ 1-9999 Variable Pulse Width Frequency Duty Cycle Square Rectangular Wave Signal Generator Module with Case
- PARAMETER — working voltage DC 3.3-30V.
- DUAL MODE — the signal generator has 2 modes, PWM mode (default) & pulse mode..
- APPLICATION — the signal generator module can be used to generate square wave rectangular wave signals for controlling DC motors or stepper motor driver.
- for servo motors, stepper motors, electric jaws, PLC pulses replacement, etc..
- PROTECTION — with anti-reverse protection, 5.08mm terminal wiring..
- EASY TO OPERATE — the signal generator can control start or stop, it can also connect the external switch to control the output signal ON/OFF..
Check Stock
Truck Upfitters Surface Mounted 100A Circuit Breaker (12V-48V, 100 Amp) for DC Automotive and Marine/Boat use: Main Power Breaker, Audio, Winches, Solar, Lighting, Electric Motors & Other Accessories.
- ... simply as a DC 100 amp circuit breaker. This is a 12-48 volt DC (Direct Current) fuse breaker & CANNOT be used IN ANY AC (Alternate Current) OR HOUSEHOLD APPLICATION..
- Be sure to consult your owner's manual when being used for your trolling motor plug and receptacle. Typically a 100 amp fuse is used on 12V trolling motors with 30, 40, or 45 lbs of thrust, 24V trolling motors with 70 lbs of thrust, & 36V trolling motors with no more than 100 lbs of thrust. A pair of 6 AWG copper lugs are included in this kit, but please verify that a AWG gauge trolling motor wire will be thick enough to handle your specific volt trolling motor plug..
- Always consult a 12-48V DC wiring specialist if you are unsure about how to determine what type (this is a DC), amp (this is a 100A), and volt circuit breaker you require for your vehicle & vehicle accessories. A 1-300 amp circuit tester can be used to determine the draw of an accessory during initial, peak, and normal operation of the accessory, but this inline breaker is not a substitute for a sound professional installation. Always consult a professional before installation..
Check Stock6 Pack Mini L298N DC Motor Driver, MELIFE MX1508 Mini Dual Channel 1.5A 1.5A 2 Way PWM Speed Controller Dual H-Bridge Replace Stepper
- Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
- Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
- Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
- Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
- Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..
Check StockHiLetgo L298P DC Motor Drive Module L298P DC Motor Drive Shield H-Bridge Drive Expansion Board High-Power DC Stepper Motor Controller for Arduino
- Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input..
- The L298P shield DC motor driver has PWM speed control mode.
- Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..
- Stack design can be directly plugged into the Arduino, easier to use..
Check Stock
AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino
- L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
- Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
- Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
- Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
- Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
Check Stock
52 Inch Minimalist Style DC Motor Ceiling Fan with LED Light, Reversible Motor and 3 ABS Blades, ETL Listed Indoor Ceiling Fans for Kitchen Bedroom Living Room, 6-Speed Remote Control
- MINIMALIST STYLE: This 52-inch indoor ceiling fan has 3 powerful blades to make your home more comfortable.
- their walnut finish attractively compliments any home decor from rustic industrial to minimalist.
- REVERSIBLE FAN: It has 3 blades designed for high volume air movement and rotates in reversible direction for changing seasonal needs and has remote controlled operation..
- REMOTE CONTROL: The convenient remote control allows you to adjust this fan's 6 speeds and 3 timer settings (1/4/8 hr.) from anywhere around your room, whether lying in bed, eating at the dining room table, or relaxing on your living room couch.
- DC MOTOR: DC motor is energy efficient and ETL listed and has convenient wall holder for remote storage. These fans save on operating costs with energy efficient DC motors. They save up to 65% more efficient than traditional AC fan motors..
- NOTICE: The DC motor can only work properly after the blades are installed (with load), so we recommend that you also install the blades during the installation test.
Check StockWINSINN 3D Printer Extruder Works with Creality Ender 3 V2 Upgrades Aluminum RepRap Prusa i3 for MK8 Drive - Silver
- ✔️UPGRADE: Perfect replacement for Creality 3D Printers Ender 3, CR-10 Series, CR-10 S4, CR-10 S5, CR-10 Mini, CR-10S, CR-10 Plus..
- ✔️This extruder feeder drive is compatible with nearly all models of 3D printers. No need to change stepper motors or other mounting hardware..
- ✔️For 1.75mm Filament. This Kit NOT include the instruction manual, we need to DIY.
Check Stock
Official Creality 3D Extruder Feeder Drive MK-8 Aluminum Upgraded 1.75mm for CR-10 Ender 3 CR-10S (Black)
- 【Upgrade Black Extruder】All Metal MK-8 Extruder Feeder Drive 1.75mm Filament. It makes loading the filament easier and smoother, with no worries about filament scraping or breaking. This extruder feeder drive is compatible with nearly all models of 3D printers. No need to change stepper motors or other mounting hardware..
- 【Wide Application】The upgrade Creality3D silver metal Bowden extruder is compatible with nearly all models of 3D printers(Ender 3/3 Pro, Ender 3 V2, Ender 3 Max, Ender 5/5 Plus/5 Pro, CR-10, CR-10 V2, CR-10 Max, CR-10 S4, CR-10 S5, CR-10S, CR-10 Plus, CR-X, CR 20/20 Pro). No need to change stepper motors or other mounting hardware..
- 【Very Easy to Install】 Unbolt the old original Creality plastic extruder & screw in the new Metal Extruder and ready to start printing. Our metal extruder kit comes with an instruction on how to put it together, which makes it easier to install. Used for 1.75mm filament of 3D printer MK8 Bowden extruder frame.
- 【Durable】 All-metal aluminum alloy, DIY aluminum block and you need to be assembled by yourself. Giving a much smoother travel and print quality. Fits a 1.75mm filament..
- 【Official Creality Original Quality】This high-quality all-aluminum construction is guaranteed to last for years,....
Check Stock
