Categories

Best Delta Table Saw Throat Plate

[2 Pack] 12 inch x 7/8 inch x .095 inch Urethane Band Saw Tires - No Adhesive Needed - Compatible with Branded Bandsaws Including Jet Grizzly, Powermatic

  • use on 14" Band Saws and 24" Scroll Saws.Table Inserts (pack of 2). Material: Aluminum.
  • They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
  • Make sure your insert recess has the locating pin on the side , not on the rear.
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
  • Please measure your saw as some Delta & Rockwell 14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required..
Check Stock

Yitu Fengshun Replace 2-PK Ryobi 9\ Band Saw Belt Tire 089120406067 for BS901 BS902 BS903 BS904

  • Will fit 14" Delta, Imports and Shopsmith.
  • Snap into place replacing your old throat plate insert.
  • Will not dull your saw teeth on your band saw blade.
Check Stock

Thomegoods Urethane Band Saw Tires FIts 12 inch x 7/8 inch x .095 inch No Adhesive Needed Fits for Jet Grizzly, & Powermatic

  • Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
  • Make sure your insert recess has the locating pin on the side, not on the rear..
  • use on 14" Band Saws and 24" Scroll Saws.2&1/2" X .100 thick Please measure your saws recess to ensure proper fit.
  • They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
Check Stock

22-540 22-560 22-580 34-080 36-610 TP400LS TS300 1400 PC305TP Carbon Brushes Compatible with Delta & Porter Cable Planer 2Pcs

  • Compatible with Porter Cable 1400 Type 1 14 inch Abrasive Cut Off Machine 1400 Type 2 14 inch Abrasive Cut Off Machine 1400 Type 3 14 inch Abrasive Cut Off Machine PC305TP Type 1 12 inch Planer.
  • Compatible with Delta 22-540 Type 1 12 inch Planer 22-540 Type 2 Planer 22-560 Type 1 Planer 22-560 Type 2 Planer 22-565 Type 1 Planer 22-580 Type 1 Planer.
  • Compatible with Delta 20-150 Type 1 Cut Off Saw TS300 Type 1 Bench Table Saw 34-670 Type 2 10 Inch Table Saw 34-670 Type 1 10 Inch Table Saw TP305 12-1/2" Portable Planer 34-080 Type 1 10" Miter Saw 34-080 Type 2 10" Miter Saw.
  • Compatible with Delta 36-600 Type 1 Table Saw 36-600 Type 2 Table Saw 36-610 Type 2 Table Saw 36-610 Type 1 Table Saw TP400LS Type 1 12-1/2" Planer TP300 Type 1 Plane.
Check Stock

Table Inserts (Pack of 3) for 14' Band saws or Scroll saws,Diameter: 2.5 in, Thickness: 0.1 in.(Please make sure this is your size)

  • Three inserts to protect your expensive blades Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
  • use on 14" Band Saws and 24" Scroll Saws..
  • 2&1/2" X .100 thick Please measure your saws recess to ensure proper fit They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
  • Make sure your insert recess has the locating pin on the side, not on the rear.
  • IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
Check Stock

Wish You Were Here

  • ⭐UNIVERSAL FIT:Switch 489105-00 On-Off Toggle Switch For Compatible with Delta Table Saw.
  • ⭐REPLACES NUMBE:Compatible with 31-695 Type 2 Sander 31-780 Type 1 Sander SA180 Type 1 Belt/Disc Sander 22-540 Type 1 12 inch Planer 22-560 Type 1 Planer 22-565 Type 1 Planer 28-150 Type 2 Band Saw 23-675 Type 1 Grinder / Finisher 14-650 Type 1 Mortiser LA200 Type 1 Lathe 31-325 Type 1 Grinder/Sander TS300 Type 2 Bench Table Saw TS350 Type 1 Bench Table Saw SH100 Type 1 Bench Shaper AP300 Type 2 Air Collector Management SA180 Type 2 Stationary Sander 34-670 Type 2 10 Inch Table Saw JT360 6".
  • ⭐WORKS FOR BRANDS: Compatible with GR450 Type 1 8" 1 6"Tool-less Quick Change Variable-Speed Grinder TP305 12-1/2" Portable Planer DP300L 12" Crosshair Laser Drill Press 17-900 Type 2 16-1/2" Drill Press 36-600 Type 2 Table Saw 50-075 Type 1 Single Stage Collector 50-665 Type 1 1.5Hp 2 Stg Collector 14-070 Type 1 14" Floor Drill Press DP200 Type 1 10" Drill Press DP400 Type 1 Drill Press GR250 Type 1 6" Bench Grinder with Lamp 46-250 Type 2 Midi-Lathe 36-610 Type 2 Table Saw 36-380 Type 1 Xl-10.
  • ⭐Specifications: Voltage: 125/250V Amperage: 20/12A Terminals: Two,On-Off Toggle Switch replaces Compatible with Delta 489105-00, 1343758 (Optional Lock).On-Off Toggle Switch re....
Check Stock

Phenolic Zero Clearance Insert for Delta Uni-Saw Contractor | Large Grizzly and Other Table Saws with a 13-3/8” x 3-3/4” x 1/2” Throat Plate Opening

  • MEASURE YOUR FACTORY INSERT AND COMPARE SIZE BEFORE YOU ORDER. Zero Clearance inserts are table saw specific. Since every table saw brand and....
  • If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate....
  • Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts. Without....
  • Zero Clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. You can....
  • This zero clearance insert is made from a high density phenolic material that was chosen for its ability to stand up to everyday workshop use. The....
Check Stock

SW7B On-Off Toggle Switch 2 Prong for Table Saws and Drill Press Replaces Black & Decker, Delta/Porter Cable 489105-00, 438010170141 Rigid/Ryobi 46023

  • ⭐UNIVERSAL FIT:Switch 489105-00 On-Off Toggle Switch For Compatible with Delta Table Saw.
  • ⭐REPLACES NUMBE:Compatible with 31-695 Type 2 Sander 31-780 Type 1 Sander SA180 Type 1 Belt/Disc Sander 22-540 Type 1 12 inch Planer 22-560 Type 1 Planer 22-565 Type 1 Planer 28-150 Type 2 Band Saw 23-675 Type 1 Grinder / Finisher 14-650 Type 1 Mortiser LA200 Type 1 Lathe 31-325 Type 1 Grinder/Sander TS300 Type 2 Bench Table Saw TS350 Type 1 Bench Table Saw SH100 Type 1 Bench Shaper AP300 Type 2 Air Collector Management SA180 Type 2 Stationary Sander 34-670 Type 2 10 Inch Table Saw JT360 6".
  • ⭐WORKS FOR BRANDS: Compatible with GR450 Type 1 8" 1 6"Tool-less Quick Change Variable-Speed Grinder TP305 12-1/2" Portable Planer DP300L 12" Crosshair Laser Drill Press 17-900 Type 2 16-1/2" Drill Press 36-600 Type 2 Table Saw 50-075 Type 1 Single Stage Collector 50-665 Type 1 1.5Hp 2 Stg Collector 14-070 Type 1 14" Floor Drill Press DP200 Type 1 10" Drill Press DP400 Type 1 Drill Press GR250 Type 1 6" Bench Grinder with Lamp 46-250 Type 2 Midi-Lathe 36-610 Type 2 Table Saw 36-380 Type 1 Xl-10.
  • ⭐Specifications: Voltage: 125/250V Amperage: 20/12A Terminals: Two,On-Off Toggle Switch replaces Compatible with Delta 489105-00, 1343758 (Optional Lock).On-Off Toggle Switch re....
Check Stock

Jet, Small Grizzly, Powermatic 64 Table Saw Zero Clearance Insert by Peachtree Woodworking PW956 Approx Dims 12-1/2 in x 3-1/2 in x 7/16 in

  • ...e list. Also be aware of the shape of your current insert of whether its round, square ends or if there are any indents or protruding notches. Insert colors may vary from images shown..
  • If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate opening. This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening. The opening is more like a custom slot cut to the exact width of your table saw blade..
  • Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts. Without a zero clearance, the wood has no support by the blade to prevent the wood from tearing out. This is especially true when cutting plywood. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert..
  • Zero Clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standar....
Check Stock

Inserts for 10\ Band saws Insert or Scroll saws (Diameter: 2.4 in, Thickness: 0.12 in) 5Pack

  • 2 Solid Aluminum Band Saw Table Inserts, Fits: ROCKWELL/DELTA Milwaukee Band Saw, Dimensions: 2 1/2" Diameter X 3/32" Thick, Fits Most Delta Models and Many Other Brands..
  • Replacing the platen provides better support, stability and precision for the workpiece being cut..
  • Before purchasing, measure the saw table inserts on your bandsaw to make sure your bandsaw can accommodate 2-1/2" diameter inserts..
  • To lock the board and prevent it from rotating, metal punches can be used on the edges of the board to create bumps or nipples on the right or left side of the board..
  • Due to slight differences in the size of the board holes in the different models of band saws that use this board, it may be necessary to lightly sand the edges of the board to fit..
Check Stock

Ridgid EB44240 Oscillating Edge Belt Sander Replacement Throat Plate Adaptor # 825841

  • Throat plate part number 089036008155. Fits Ridgid miter saw models R4112, R41121 and R4113..
  • Brand New Unused Parts We have a warehouse in the US and will ship from the US, you can expect to receive your shipment within 5 days..
  • Please feel free to contact us if you have any problem.
  • Send us your range model if you would like verification that this will work on your model.
Check Stock

Delta Power Equipment Corporation 36-502 Dado Throat Plate Colors may Vary

  • Designed for Delta Table saws- 36-5000, 36-5052, 36-5100, 36-5152.
Check Stock

Dewalt 0009900146726-02 Genuine Original Equipment Manufacturer OEM Part

  • Compatible with Delta Table saws 36-5000,36-5052,36-5100, 36-5152...
  • Also work with any 13/16" X 8" diameter stacked dado.please check the size before purchase..
  • Please pay attention to the position of the tabs during installation, and make slight adjustments if necessary..
Check Stock