Categories

Best Electric Motor Shaft

Electric Skateboard Motor BLDC D6374 190KV 3350W Belt Brushless Motor Outrunner Sensored 15t Pulley Engine for DIY Electric Longboard,Off Road e-Skateboard,Scooter,esk8,ebike Part Accessories-GOESKBA

  • Overview GOESKBA Electric Skateboard Motor D6374 190KV Max 3350W 6130RPM 12S 25mm shaft D-shape motor adopt high-end material and professional design make sure provide powerful power for eskateboard,ebike,scooter,robots etc..
  • Features Precision design can deliver good performance and efficency also give maximum conversion of energy , high-end material make sure excellent heat dissipation and low energy consumption,professional design make sure electric skateboard starts smooth and low noise..
  • High-end Material Japanese Kawasaki silicon steel sheet iron core reduce the iron loss of the motor and improve the efficiency of the motor,420 material shaft more sturdy,good finishing on the whole outer body to enable motors dustproof,Japan NSK Bearings improve the service life of the motor、eliminate abnormal noise..
  • Professional Design double side arc-shaped convex magnets array can better match work with VESC FOC mode to greatly reduce the noise,hall plate fixed in the stator tightly,three M3 screws dispensing reinforced lock shaft prevent deviation,anti loose T-type motor shaft prevent slipping and loosening,multi-strand winding better dissipation and avoid skin effect..
  • Widely application GOESKBA Electric Skateboard Motor D6374 can be widely used in Electric....
Check Stock

Mophorn 1 Hp Electric Motor 3450 RPM 11.2-5.6 A Single Phase Motor AC 115V 230V Air Compressor Motor 56C Frame Suit for Agricultural Machinery and General Equipment

  • Single Phase: The motor is 1HP single phase electric motor, features with 115/230V voltage and 11.2/5.6A full load amperage.
  • Fitted Frame and Shaft: With 56C frame, the electric motor also has 1.875 inch length and 0.625 inch diameter keyed shaft.
  • High Speed: The electric motor features 3450RPM rated speed and 3600RPM synchronous speed. High speed meets your different needs..
  • Fan Cooled: Our electric motor is TEFC (Totally Enclosed Fan-Cooled) motor. A built-in fan helps to dissipate heat and prevent the motor from overheating..
  • Universal Motor: Universal Motor- Universal used for the matching of water pumps, agricultural machinery and general equipment..
Check Stock

BestTong Micro DC 12V-24V 10000RPM 775 Motor Ball Bearing Large Torque Dual Output Shaft High Power Low Noise Brushed DC Motor for Electrical Tools DIY

  • DC 12V 24V round shaft 775 electric motor, with dual accuracy ball bearing.
  • Note: The motor starting current needs to be 10A.
  • With copper wire production, durable for using. Easy to wire and install. Durable construction for long-lasting performance. Wide applied to electric tools, electric fans, electric cleaners, etc. Small size but large torque.
Check Stock

1.5-6V 5000-20000RPM DC Micro Motor 260 Mini Motor Electric Motor Round Shaft for RC Boat Airplane Toys Model DIY Hobby - (5 PCS)

  • 【Product Name】:260 DC Mini Electric Motor. Color : Silver Tone..
  • 【High Quality 】: Material : Metal, Electronic Parts, More wear resistant, corrosion resistant and durable..
  • 【Specifications】:Rated Voltage : DC 1.5V-6V.
  • Rated Speed: 5000-20000RPM, Shaft Diameter: 2mm.
  • Shaft Type: Round Shaft, Motor Body Diameter: 21.
  • Motor Body Length: 25mm. Mounting hole pitch: about 10mm.
  • 【Applications】: Used for electronic game machine Printer, Rearview Mirror, Head Light Beam Level Adjuster, Car Toys, DIY hand drill, electronic equipments etc..
  • 【Package Included】: 5 x 260 DC Mini Electric Motor.
  • Have our worry-free 90-daywarranty and friendly customer service. › See more product details.
Check Stock

TarpingUSA Apache Series Tarp Motor for Dump Truck 1.5hp 50:1 Universal 12V Electric Tarp System Motor

  • 3-YEAR WARRANTY: This electric tarp motor will deliver years of speed, strength, and reliability under normal use. Due to electric motor efficiency and electric power available from your vehicle's battery or alternator, these units are rated for intermittent use. Use for short periods of time only, allowing it to cool between uses. If your motor becomes too hot to touch, stop operation and allow it to cool. Recommended wire is 6 or 8 gauge..
  • 50:1 GEAR RATIO, 1.5 HP, 12V Direct Current, 40 Amps, Reversible Action, 44 NM Operating Torque. One of the FASTEST, Strongest Electric Tarp Motors Available..
  • UNIVERSAL FIT FOR DUMP BODIES UP TO 28 FEET. Dump Truck Tarp Motor has a 3/4 inch output shaft and a 5-bolt mounting pattern works with most Electric Tarp Systems..
  • INCLUDES REFLECTIVE CHROME MOTOR COVER, all necessary mounting hardware, and 3-Year warranty.
  • OUTPUT SHAFT is 3/4 inches thick and 3-3/4 inches long with a 5/16" hole drilled at 1 inch and at 2 inches for best fit..
Check Stock

High Speed Brushless DC Motor Kits 2000W 60V Electric Gokart Motor 4250RPM Rated Mid Motors with Controller Pedal Throttle for E-Scooter E-Bike Dirt Bike Motorcycle

  • ...1T, Maximum Current: 65A. Rated Torque: 6 N.m / 849.67 oz.in, Shaft Diameter: 0.47'' / 12 mm, Length (no Shaft): 5.31'' / 135 mm, Length (with Shaft): 6.3'' / 160 mm. Package includes: 1 x Brushless DC Motor, 1 x Controller, 1 x Multi-purpose Wrench, 1 x L-Shaped Wrench, 1 x Screw Set..
  • 3000W Brushless Motor: The dc electric go kart brushless motor adopts a 100% copper core for low noise operation and excellent speed regulating performance. The high-precision rotor features high-tech components, a clean finish for water resistance, and high working efficiency. Get ready to leave the competition in the dust..
  • Sturdy Aluminum Construction: The electric brushless dc motor kit features an aluminum alloy shell that resists heat, cold, and deformation, ensuring it will not rust easily. This dc electric motor is a forward and backward rotation motor so that you can switch rotation gears effortlessly..
  • Speed Controller Included: This dc electric motor brushless comes with a controller to provide speed control at a desirable range, speed adjustment method: Potentiometer. Model: BY24WF01-B, Current: 65A, Phase Degree: 120°, Conversion Efficiency: 90%, Under Voltage Protection Voltage: 61±0.5V..
  • Multiple Application: The brushless motor outshines the brushed moto....
Check Stock

Greartisan DC 12V 60RPM 7Kg.cm 8mm Single Shaft Self-Locking Reversible Worm Gear Motor with Cable, High Torque Speed Reduction Motor, Turbine Electric Gearbox Motor

  • 【High Torque & Lower Noise】: Long carbon brush high life, high precision gear design, small size, high torque, low noise, high efficiency..
  • 【Positive-Negative Rotation】This type is miniature High Torque Electric Worm Gear DC Motor, which can change shaft rotation direction while the wiring positive andnegative be changed..
  • 【Self-Locking】: Turbo worm geared motor with self-lock, that is, in the case of motor without electric, the output axis is fixed, self-lock..
  • 【Versatile】: The reducer output shaft arranged vertically with the motor shaft, whole motor output is relatively short,can be widely used in various of occasions that require special installation size..
  • 【Application】: Boat, Car, Fan, Home Appliance, BBQ, Machinery and equipment, automation instruments, electric curtain, stage lighting, counter, faucet, safe, wet towel dispenser, vending machines, automatic monitoring and other modern art..
Check Stock

Carolina Tarps Tarp Motor for Dump Truck 1.5hp 50:1 Universal 12V Electric Tarp System Motor

  • 50:1 Gear Ratio, 1.5 HP, 12V Direct Current, 40 Amps, Reversible Action, 44 NM Operating Torque. One of the FASTEST, Strongest Electric Tarp Motors Available..
  • UNIVERSAL FIT for Dump Bodies up to 28 feet. Dump Truck Tarp Motor has a 3/4 inch output shaft and a 5-bolt mounting pattern works with most Electric Tarp Systems..
  • Output shaft is 3/4 inches thick and 3-3/4 inches long with a 5/16" hole drilled at 1 inch and at 2 inches for best fit..
  • INCLUDES reflective chrome housing, all necessary mounting hardware, and 3-Year warranty.
  • 3-YEAR WARRANTY: This electric tarp motor will deliver years of speed, strength, and reliability under normal use. Due to electric motor efficiency and electric power available from your vehicle's battery or alternator, these units are rated for intermittent use. Use for short periods of time only, allowing it to cool between uses. If your motor becomes too hot to touch, stop operation and allow it to cool. Recommended wire is 6 or 8 gauge..
Check Stock

BEISGUANGS Electric Bike Accessories Universal Torque Arm Conversion Kit for ebike Front or Rear Hub Motor Wheel E Bike kit Easy Install Reinforcement

  • 【Material】Torque arm is made of high-quality metal, with good design and strong resistance to deformation. The surface is galvanized to prevent corrosion and maintain gloss..
  • 【Size】Torque arm length 86mm, shaft hole 14mmX10mm, C clip 14mmX10mm, arm thickness 3mm, hub bracket thickness 4mm, C clip thickness 3mm, can be adjusted according to different configurations..
  • 【Function】This torque arm will help prevent the motor from loosening from the bicycle's front fork (front) or frame (rear fork), and prevent the slotted shaft from bending or breaking your dropouts. Necessary for high-power motors..
  • 【Installation】This torque arm is suitable for electric bicycle motors and electric bicycle conversion kits. Easy to install, the product is suitable for normal motor shafts, except for special shafts (the size of the motor shaft does not exceed 14mm)..
  • 【List】Contains 1 long reaction arm + 1 short reaction arm + 1 hex screw + 1 collar + 1 nut + 2 washers. (as the picture shows). It can provide maximum protection for your electric bicycle, motor and hub motor wheel..
Check Stock

COLIBROX AS-4FS 1/2 Motor Arbor to 1/2 Threaded Shaft Adapter

  • Converts electric motor to Grinder or Buffing machine.
  • Fits 1/2" Motor Shafts,Converts 1/2" motor shaft to 1/2" Threaded shaft,Wheel Widths Up To 1 1/16 in.
  • Lock on to motor shaft with 2 hex set screws,1/2"-20 Right Hand thread.
  • Holds Grinding wheels, Wire wheels or Buffing wheels with 1/2" hole.
Check Stock

86 LBS Thrust Trolling Motor, 24V Transom Mounted Saltwater Electric Outboard Motor 8 Speed w/LED Battery Indicator and Telescoping Handle for Kayak, Inflatable Fishing Boats

  • POWERFUL ELECTRIC TROLLING MOTOR - This 86 lbs thrust 24V motor provides excellent power and efficiency for any boater. It features a 28-inch shaft, a 10 points LED battery meter, a 6 Inch telescoping handle, and 3 blade propeller. The shaft angle and propeller depth can all be adjusted and locked into place when needed..
  • ERGONOMIC EXTENDABLE HANDLE - 8 speeds adjustable tiller (5-sp forward & 3-sp reverse) puts total control at your fingertips for a smooth and easily controlled ride. Also, the 6-inch telescoping handle allows you to get easy and comfortable operation of your electric boat motor..
  • 28-INCH FIBERGLASS COMPOSITE SHAFT - High tensile strength and corrosion resistance adjustable shaft allow for proper depth placement in different water conditions. You can set it to the desired height to comfortably steer by sitting or standing. 28” shaft is more suitable for sitting..
  • 10-POINT LED BATTERY INDICATOR - There is a 10-level LED indicator display of the battery power on the top of the propeller, allowing you to check the power condition at any time and prepare for charging in advance to avoid running out of pow....
Check Stock

LYNICESHOP Electric Outboard Motor, Electric Outboard Trolling Motor Boat Engine Long Shaft 48V 1000W Heavy Duty Trolling Electric Trolling Motor for Kayak Canoe Fishing Boat Small Yacht

  • Electric Outboard Motor: Electric outboard trolling motor Model: DD-48V-1000W, Shaft length: 508mm(Suitable Electric Outboard Motor: Electric outboard motor Model: DD-48V-1000W, Shaft length: 508mm(Suitable for ships with stern plate 45-55 cm), Use voltage:48V, Current:18A, No-load Speed:3000 rpm, Recommended Battery: 48V 100A/3-4H, Product Weight:10.5KG, Power:1000W, Speed:15 KM /H, Gross Weight / Net Weight:10.5KG/13KG, Start Key:NO, Reverse Gear:NO..
  • High Quality Materials: Electric outboard trolling motor is made of aluminum, light weight, good electrical conductivity, thermal conductivity, ductility and corrosion resistance, and pure copper core brushless motor, strong power, low energy consumption and long service life, aluminum alloy suspension bracket, 90° rotatable bracket, more stable and durable..
  • Superior Performance: Electric outboard motor has ultra-low power consumption to maximize the use of your 48V battery, vertically mounted engine design for increased power, performance and durability, excellent outboard corrosion prevention system and anode for increased durability, suitable for small watercraft such as inflatable boats, canoes and aluminum fis....
Check Stock

Alfa Wheels Electric Scooter Motor Currie Technologies 24 Volt 500 Watt DC for 500 Series Schwinn & IZIP Reversible with 11 Tooth Sprocket #25 Chain Model Numbers XYD-6B SD-156 XYDJ130601664

  • APPLICATIONS: This electric scooter motor from Currie Technologies can be used for scooters, for Mini Bikes quad and Go-Karts using 450W or 500W motors with similar mounting brackets., for bicycles and for do it yourself enthusiasts who would like to use it for diverse applications. This motor should work with Schwin and IZIP 500 series electric scooters. This electric motor should also work with any other brand with similar specs..
  • MOTOR SPECS: Model XYD-6B Motor, Type Brush, Voltage 24 Volt DC, Output 500 Watts, Rated Speed 2600 Rpm, Rated Current 28 Amp, Sprocket #25 Chain 11 Tooth, Rotation Reversible, Removable Set-Screw Sprocket, This motor is capable of rotation in either the clockwise or counterclockwise direction by reversing the motor's power wires..
  • COMPATIBILITY: Currie Technologies part number SD-156, OEM motor on 500 Series Schwinn & IZIP electric scooters (chain drive) compatible with eZip E-500, GT-500, IZIP I-500, Mongoose M500, Schwinn S500..
  • DIMENSIONS: Case Length 3-7/8" (98 mm), Case Diameter 3-15/16" (100 mm), Drive Shaft Length 1/2" (13 mm), Drive Shaft Diameter 3/8" (10 mm), Mounting Hole Distance 3-15/16" (100 mm), Center to center mounting hole distances approximately 3-7/8.
Check Stock