Categories

Best Electrode Clamp

Electrode Holder 500 Amp Welding Electrode Holder Set, Heavy Duty Jaw Holding Plier Electrode Clamp for Arc MMA Welder,Black

  • 【High Quality Welding Electrode Holder】The upper and lower clamps of the electrode clamp are made of high copper alloy for maximum conductivity and strength. High quality electrode holder with 500A current capacity, comfortable insulated handle, convenient and easy to operate. Ideal for most arc, MMA, hand welding work.
  • 【Heat-resistant insulation for Safety】The handle is molded from a durable glass-filled nylon material for good heat and impact resistance. Glass-filled nylon handle and clamp insulated for maximum operator protection and safety.
  • 【Groove Jaw Design】The grooved jaw for firm grip of rods in 45°, 90°, 135°, 180° positions. Clamping Device holds the stick electrode tight so it will not slip while welding and transfers the welding current to the stick electrode.
  • 【Welding Chipping Hammer & Wire Scratch Brush】Welding chip hammer is made of high strength and toughness steel. Dual-headed design, one end is flat chisel, the other end is pointed chisel, convenient operation in narrow space.Coil spring handles reduce vibration and improve comfort. The wire brush is made of stainless steel bristles and with wooden handle, they are durable and have a strong cleaning ability..
  • 【Work Great】Which are easy to remove and clean corrosi....
Check Stock

WeldingCity 100-ft 2-AWG USA-made Heavy Duty Welding Cable Highly Flexible Durable EPDM Rubber Jacket 600V -50C-105C Black

  • ...istant to chemicals, oils, and acids and is also weather, ozone and sunlight resistant. Available welding cable sets: welding cable only.
  • cable set with terminal lugs and cable set with Dinse connectors..
  • Welding Cable Set With Terminal Lug includes: 2-AWG USA-made welding cable at selected length, one 300-amp stick electrode holder with accessory kit, one 300-amp ground clamp and three zinc-plated copper terminal lugs (1/2" stud hole)..
  • Welding Cable Set With Dinse Plug includes: 2-AWG USA-made welding cable at selected length, one 300-amp stick electrode holder with accessory kit, one 300-amp ground clamp, one zinc-plated copper terminal lug (1/2" stud hole) and two Dinse-type 35-50mm male connectors..
  • Heavy duty 300-amp stick electrode holder with strong jaw spring.
  • both upper and lower jaws made of copper (brass) with increased operator comfort. Zinc-plated steel 300-amp work clamp with strong spring, copper plated jaw, copper braid, copper plated hex screw for secured cable connection. Dinse-type twist-lock cable connector (male) with heat and oil resistant covers and accessories.
  • 1/2" (12.7mm) pin. Accepts cables AWG #2-1/0 (nominal cable area 35-50mm²)..
  • U.S. based welding and hardware supplier. Strong technical support with experienced customer ....
Check Stock

SP Bel-Art Flexible Gooseneck Arm for F18317-1000 Electrode Holder (F18315-0000)

  • Molded of chemical and corrosion resistant acetal copolymer links with ball-and-socket joints.
  • Arm can hold and position a pH meter or similar tools.
  • One end is designed to accept the F18317-1000 Electrode Holder while the other has a 12.7mm (1/2") diameter stainless steel pin for attachment to a clamp or base.
  • Base and electrode holder sold separately.
Check Stock

ETCR2100A+ Digital Clamp Ground Earth Resistance Tester Meter 0.01Ω-200Ω

  • Clamp Size:Φ1.26"(32mm),Clamp table size: 10.24"×3.54"×2.6"(260mm × 90mm × 66mm).
  • Structural Feature：Clamp CT,and can measure the ground fault which can not be measured by traditional method.
  • Measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
  • Multi keyboard operation panel, new alarm and save functions.
  • This Clamp meter widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc.
Check Stock

Goplus 250 AMP MMA Welder ARC Welding Machine 110V/ 220V Soldering Accessories Tools

  • 【Profession Grade ARC Stick Electrode Welder】Detailed treatment makes this welding machine highly efficient and practical. Stick electrode welding machine for MMA welding in alternating current (AC). Perfect welding performance, ideal for welding mild steel and stainless steel..
  • 【2 levels transformer】2 levels of transformer, 110V and 220V. Fit both home and professional use..
  • 【Stable and Durable】Compact construction and exquisite MMA ARC welding machine, made of heavy duty stainless steel body, painted with durable yellow paints, ensure its long-last serving life-span..
  • 【Portable Design】Features 2 easy carrying handle handles and 2 Wheels for easy access and movement during your maintenance tasks, adds extra maneuverability. Can be used anywhere u need..
  • 【Safe with A Lot of Complimentary Necessities】Build-in fan on the machine to help heat dissipation. Features with thermal overload protection to ensure safety. It also comes with a copper electrode holder, a ground clamp, a protection mask and a brush/chipping hammer..
Check Stock

HITBOX TIG Welder 110V 220V 200A 2T 4T TIG Stick MMA IGBT Inverter High Frequency Dual Volatge Welding Machine (Model: TIG200A)

  • Ship from the United States. Dual Volt 200 amp IGBT Tig Stick Welder with tig torch, earth clamp, electrode holder and gas tube..
  • Adopt newly IGBT inverter technology, Compared to MOS Technology, greatly reduce breakdown.
  • Inverter frequency up to 100KHZ, the technology is mature, stable performance.
  • TIG Welding thickness 0.5-6mm, and application of electrode diameter (MM): 2--3.2mm.
  • Easy arc ignition, litter spattering, stable current and good shaping.
Check Stock

Lincoln Electric Inverter ARC 120 K2789-2

  • Century DC Inverter stick welder 70 Amp welds up to 1/4 in. This 17 lbs. welder has 120-Volt input. One-year warranty parts and labor. 20% Duty cycle..
  • 6 ft. input cable with attached 15 Amp plug.
Check Stock

Hobart 500570 Stickmate 160i

  • Easy to carry & store. Weighs under 20 lbs.
  • 10 ft. (3 m) electrode cable with heavy- duty holder.
  • Easy, quick, reliable starts with hot start technology.
  • Up to 160A output. Welds up to 5/32 inch mild steel.
  • 120V/240V input power. Allows connection to 120 or 240V receptacles without tools.
Check Stock

SUNGOLDPOWER ARC MMA 200A Welder Dual 110V 220V IGBT Hot Start Welding Machine DC Inverter Welder 200 AMP LCD Anti-Stick

  • Please Note: some cheaper welders are only about 7-10lbs, looks like a toy.
  • however, SUNGOLDPOWER welder is heavier than others, because SUNGOLDPOWER welder is full-bridge welder (many cheap welders are half bridge welder), we use more high quality components to support its perfect working and long-life time..
  • 2.Advanced control module IGBT dual 110V and 220V, improves the performance of the welding machine. IGBT MMA welder adopting advanced full bridge IGBT inverter technology.
  • 3. Anti-sticking preventing against over loading the unit easing removal of the electrode,thermostatic control,fan cooled carrying strap and handle..
  • 4. Hot start, arc force overload protection：over-voltage protection, under voltage protection, over current protection, over load protection.
  • 5. Supplied complete with AC Plug，electrode holder and cable, earth clamp and cable, Complete package..
Check Stock

OhLectric OL-38707 High-Conductivity Ground Pipe Clamp - Made of Copper Alloy - Connecting Grounding Electrodes to Water Pipes Clamp - Non-Direct Burial Pipe Clamp - ½ Inch - 1 inch Pipe Range

  • ...round clamps are extremely durable with high strength and are built to last for a lifetime. Our pipe clamps are designed to fit and organize in a safe manner with the maximum flexibility to suit your needs!.
  • MULTIPURPOSE: These pipe ground clamps are an excellent choice for either clamping the pipes to the grounding electrode or you can even use these clamps to securely mount the pipes on walls. It can also be used for connecting bare wires to pipes or steel water pipe or tubing..
  • CORROSION FREE: The ground clamp for pipe can be attached to the grounding electrode and the pipe by the means of indirect burial with the screws provided. To prevent rusting, the screws are coated with zinc plated steel alloys which totally eliminates the chances of corrosion on the clamps..
  • SAFETY TESTED: All our products are certified by Culus for their safety and specification standards set by them. We follow every step to ensure all the housing rules and regulations are followed as we value customer satisfaction and safety more than anything else..
  • ADAPTABLE FIT: These pipe grounding clamps come in a variety of sizes which are well equipped for all wire ranges between 2-10. And also they support all pipe sizes from the smallest ½ inch to 1 inch. The screw thread on the cl....
Check Stock

ABN Pneumatic Spark Plug Cleaner – Spark Plug Sandblaster Plug Cleaner Tool with Abrasive Universal Sparkplug Cleaner

  • PROLONG THE LIFE OF YOUR SPARK PLUGS: Are your spark plugs underperforming? Clean them up with the ABN Spark Plug Cleaner Pneumatic Sand Blaster....
  • SPARKPLUG SANDBLASTER CLEANER KIT: Includes a spark plug cleaner unit, a fabric spark plug cleaner bag, an airbag clamp, a 1.7 oz (.1lb) bag of....
  • BUILT TO LAST: Constructed of a thick, durable plastic base with brass fittings, and a steel clamp provides this air spark plug cleaner sandblaster....
  • SIMPLE INSTALLATION AND SET UP: 2 mounting flanges on each side allow you to mount the spark plug cleaner machine vertically on a wall or post.
  • EASY TO USE: Hook your compressor to the spark plug tool cleaner and insert the spark plug (electrode-side down) into the rubber cover at the top of....
Check Stock

2021 LightningMTS 275 AC/DC TIG with Pulse/MIG/Stick Welder Dual Voltage 110v/220v

  • 12 ft. Everlast 18 Series Water Cooled TIG torch with series 35 DINSE-style connector.
  • 10 ft. Series 36 MIG torch with Euro style quick connect fitting.
  • Stick electrode holder with 10 ft. cable and 35 series DINSE-style connector.
  • Work clamp with cable 10 ft. cable and 35 series DINSE-style connector.
  • Spare consumable starter kit (does not include tungsten).
Check Stock

Hobart 770655 Cup, Swirl Ring, O-Ring Kit for the AirForce 700i

  • Easy to carry & store. Weighs under 20 lbs.
  • 10 ft. (3 m) electrode cable with heavy- duty holder.
  • 6.5 ft. (2 m) power cord with MVP adapters for 120V and 240V ..
  • Easy, quick, reliable starts with hot start technology.
  • Up to 160A output. Welds up to 5/32 inch mild steel.
  • 120V/240V input power. Allows connection to 120 or 240V receptacles without tools.
Check Stock