Categories

Best Embedded Microcontroller Support

Arduino MKR WAN 1310 [ABX00029]

  • The perfect IoT node and building block for adding to Lo-Ra connectivity to low power wide area IoT devices.
  • Very long battery life - the latest low power architecture means the power consumption is able to go as low as 104uA for extended battery life. It is also possible to use the USB port to supply power (5V) to the board, so you can run the board with or without batteries.
  • Local storage - On board 2MByte Flash to facilitate data logging and Over-The-Air (OTA) functions.
  • Enhanced Security - credentials and certificates are stored in the boards crypto chip, an embedded secure element.
  • Powerful - The MKR WAN1310 is based on the Atmel SAMD21 microcontroller and a Murata CMWX1ZZABZ Lo-Ra module.
Check Stock

ARCELI TL866II Plus USB High Performance EEPROM Flash BIOS Programmer for ATMEL AVR ATMEGA AT90 PIC GAL SRAM CMOS

  • It can automatically identify the operating system to install and run under WIN2000 / WIN XP /WIN 2003/ WIN 2008/ WIN VISTA / WIN7 / WIN8 / WIN10 (32BIit/64Bit).
  • The programming speed is greatly improved . It is suitable for small batch production and supports 4 programmers for one computer..
  • A wide range of chip support, supports the chip 15000+, supports a variety of 24 25 26 27 28 29 37 39 49 50 series of serial and parallel memory chips, microcontroller 51 series, ATMEL AVR ATMEGA AT90 series, MICROCHIP PIC10 PIC12 PIC16 PIC18 series microcontroller , GAL programmable logic device programming, SRAM test,54/74 and CMOS4000 integrated circuit integrated functional test..
  • Support NAND Flash chip, the function is complete and comprehensive, the capacity supports to 8Gbits. 25 series Nor Flash capacity support to 512Mbits..
  • Pin contact check function, poor contact pin can pinpoint.
  • Ultra-low power consumption: the entire programmer uses ultra-low-power chips, using USB interface, the first truly all chip programming without external power integrated programmer..
Check Stock

NOYITO Voltage to Current Module 0-10V to 0-20mA

  • NOYITO Voltage to Current module, 0-2.5V ,0-3.3V,0-5V,0-10V,0-15V,0-24V voltage signal conversion to 0-20mA or 4-20mA current signal output, by adjusting the voltage to adjust the size of the current. Can be used to generate the signal source, valve adjustment, inverter control, PLC debugging, instrumentation test, LED test, analog transmitter.003cbr003e.
  • Implement the industry standard voltage (0-2.5V ,0-3.3V,0-5V,0-10V,0-15V,0-24V) into an industry standard current (0-20mA, 4-20mA)., linear output, the output signal can be directly connected to the AD converter, with the AD function with the microcontroller connection.003cbr003e.
  • Using single-chip embedded technology. The module is small and easy to use in different places.003cbr003e.
  • Easy to use, can be fine-tuned by potentiometer.003cbr003e.
  • Module working voltage: DC12-24V . 【Please read the product pictures on the left side of the page for the wiring diagram of the product.】003cbr003e.
  • 【Manufacturer's One-year After-sale Warranty】.
Check Stock

GY-AS3935 Lighting Sensor Module SPI I2C MA5532-AE Lighting Strike Thunder Storm Distance Detector Breakout Board

  • Reference link: https://tinyurl(dot)com/AS3935-light-detector.
  • Video link: https://youtu(dot)be/oXqSIyaHR_I.
  • The splitter uses an inductor (antenna) designed specifically for this application, and the board is fully calibrated.This ensures that you can support low-level IC calibration without having to write a large back-end – focus on your end application!.
  • This sensor cannot drive an LCD display on it own It will need a microcontroller, like ESP8266/ESP32 or Arduino Pro Mini / Pro Micro 3.3V The Microcontroller will control the sensor and control the display as well..
  • What you will get is : 1 X GY-AS3935 Lightning Sensor.
Check Stock

Handled Pet Microchip RFID Reader, Portable Rechargeable 134.2Khz Animal Handheld Portable Scanner OLED USB

  • Good compatibility: This RFID handheld reader is used in animal identification areas, and can identify animal tags that comply with the standards IOS11784 / IOS11785, FDX‑B..
  • Equipped with advanced and sensitive chip: The reader is equipped with advanced chip, receiving circuit and embedded microcontroller, combined with strict decoding algorithm to receive, verify and read data that can be adapted to electronic identification..
  • High sensitivity display: high sensitivity, small working power, portable and cost-effective features make it even better. Real-time data is displayed on the LED screen..
  • High-definition display, long-lasting battery life: low-frequency 134.2Khz electronic tag reader with OLED display and USB charging function. Stable, safe and reliable performance. Equipped with a built-in 200mAh lithium battery, which can be charged for 90 minutes and work continuously for 4 hours..
  • Professional and wide use: Mainly used for poultry management, livestock breeding management, fish management, pet identification management, anti-counterfeiting items, etc..
Check Stock

Ingcool Acrylic Case for Raspberry Pi Pico, Include Raspberry Pi Pico with Pre-soldered Header (Color-Coded), Based on Raspberry Pi RP2040 Chip, Support C/C++/Python

  • A low-cost, high-performance microcontroller board with flexible digital interfaces, incorporates RP2040 microcontroller chip designed by Raspberry Pi.
  • Dual-Core Arm Cortex M0+ processor, flexible clock running up to 133 MHz.
  • 26 × Multi-Function GPIO Pins, configurable PIN function, allows flexible development and integration.
  • Support C/C++, MicroPython, comprehensive SDK, dev resources, tutorials to help you easily get started.
  • Clear acrylic protection case for Raspberry Pi Pico, dule-sided protection, with customized key cap, pinheaders/connectors still accessible.
Check Stock

HiLetgo HC-06 RS232 4 Pin Wireless Bluetooth Serial RF Transceiver Module Bi-Directional Serial Channel Slave Mode for Arduino

  • Works with any USB Bluetooth adapters, running in slave role: Pair with BT dongle. Led indicate Bluetooth connection status, flashing Bluetooth connectivity, lit the Bluetooth connection and open a port Backplane.
  • Core module uses HC-06, leads from the module interface includes VCC, GND, TXD, RXD, reserve LED status output pin, the microcontroller can be judged by the foot state Bluetooth has connected KEY pin slave invalid..
  • Small size, low power consumption,high sensitivity for send and receive. Bluetooth version: V2.0+EDR &Operating voltage: 3.3V &Host Interface:UART &Storage Temperature:-40℃~+150℃&Signal coverage: 30ft &Item size: 4.3 * 1.6 * 0.7cm &Item weight: 3g..
  • The module is mainly used for short-range data wireless transmission,such as Bluetooth wireless data transmission,Industrial remote control, telemetry,Traffic, underground positioning, alarm,Smart home ect..
  • Industrial serial port bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc. Computer and peripheral devices..
Check Stock

KOOBOOK 2Sets HX1838 NEC Infrared IR Remote Control Sensor Module IR Receiver Module DIY Kit for arduino

  • Operating voltage 5V.Output form: Digital output..
  • VCC: 3.3V-5V external voltage (can be directly connected to the 5v microcontroller and 3.3v microcontroller).GND: external GND.IN: external microcontroller I/O port, I/O port has been designed 10K pull-up resistor..
  • Kit theory test distance of about 5-8 meters, but the practical application depends on the ambient factors you use, as well as the middle barrier (such as diaphragm, glass, obstructions or other material blocking), receiving head with HX1838 with power work instructions lights, receive 38K frequency any remote coding data..
  • remote Control Battery:CR2032 Button batteries (Not Included).
Check Stock

Adafruit USB Micro-B Breakout Board [ADA1833]

  • Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project..
Check Stock

Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit

  • Perfect for microcontroller storage and retrieval - whether it's images, fonts, GIFs, audio files, or sensor logs.
  • Multi-pin data protocol (up to 4 data pins at once!).
  • Can be used with SDIO hardware support - clocked faster that SPI.
Check Stock

Treedix 2pcs ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Treedix ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter with Cable

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Adafruit Metro 328 with Headers - ATmega328

  • ATmega328 microcontroller with Optiboot (UNO) Bootloader.
  • A fully assembled and tested microcontroller and physical computing board with through-hole headers attached.
  • 32KB of flash and 2KB of RAM, running at 16 MHz.
  • Compatible with "Classic" and "R3" Shields.
Check Stock