Categories

Best Ferrule Pipe Hose Fitting

DERNORD Sanitary Fitting Reducer Fitting SUS304 Tri Clamp Ferrule Style 2\ Tube OD to 1-1/2\ Tube OD

  • Concentric reducer fitting to connect two pipes of different diameters that are along the same pipe axis.
  • Fitting clamps to tubing on both ends for a non-permanent seal, providing take-down access.
  • Stainless steel 304 for resistance to corrosion and high temperatures.
  • Ferrule Size(51MM end):64mm ferrule fits 2" tri clamp.
  • Ferrule Size(38MM end):51mm ferrule fits 1.5" tri clamp.
Check Stock

Beduan Brass Compression Fitting, Insert Tube Support Compression Sleeve Fitting 1/4\ Tube ID (Pack of 10)

  • ✅[QUALITY MATERIAL] Made of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube ....
Check Stock

QiiMii Sanitary Fitting Reducer Fitting SS304 Tri Clamp Ferrule Style 3\ Tube OD to 2\ Tube OD (3 INCH X 2 INCH )

  • Ferrule Size(76MM end):91mm ferrule fits 3" tri clamp.
  • Ferrule Size(51MM end):64mm ferrule fits 2" tri clamp.
  • Concentric reducer fitting to connect two pipes of different diameters that are along the same pipe axis.
  • Fitting clamps to tubing on both ends for a non-permanent seal, providing take-down access.
  • Made of Stainless steel SS304,there for resistance to corrosion and high temperatures.
Check Stock

Hilitchi 8Sizes Tube OD 4mm-16mm Brass Compression Sleeves Ferrules Compression Fitting Kit Metric 220Pcs

  • ✅ [QUALITY MATERIAL] Made of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅ [FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅ [HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅ [APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon t....
Check Stock

Hilitchi 3Sizes Tube OD 1/4 5/16 3/8 Brass Compression Sleeves Ferrules Compression Fitting Kit (SAE, 105Pcs)

  • ✅[QUALITY MATERIAL] Made of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube ....
Check Stock

Compatible with Compression Sleeve Puller（03943）-- Sleeve Remover for 1/2-Inch Compression Fittings Only -- Corroded & Frozen Supply Stops --Plumbing Tools Compression Ring Removal Tool

  • ...for working on frozen or corroded supply stops,corrosion resistant & wear resistant..
  • Operating Steps--1.Remove the old compression fitting or the old angle stop. 2.Put the nut of pipe to the golden threaded mouth of the puller tool to tighten the screw 3.Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. 4.The puller tool will automatically pull compression nut and ferrule..
  • 100% QUALITY GUARANTEE – ONE YEAR MONEY BACK. Buy with confidence and add to cart now! We provide 100% customer support 1-year product warranty. Have any problem, please email us, we'll reply within 12 hours..
Check Stock

QMINOX 2 Inch × 1.5 Inch Sanitary Fitting End Cap Reducer Stainless Steel 304 Sanitary Concentric Reducer Tri Clamp Clover

  • End Cap Reducer Ferrule Size 64mm = 2 Inch Tri Clamp.
  • End Cap Reducer Ferrule Size 50.5mm = 1.5 Inch Tri Clamp.
  • Concentric End Cap Reducer Fitting to Connect 2 Pipes of Different Diameters That are Along The Same Pipe Axis.
  • Sanitary Fitting clamps to tubing on both ends for a non-permanent seal, providing take-down access.
  • Stainless Steel 304 Sanitary Fitting for Resistance to Corrosion and High Temperatures.
Check Stock

Class A Customs 13 Gallon Water Tank & Plumbing Kit T-1300-BPK

  • ...Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • 13 GALLON TANK MEASUREMENTS 21” x 9” x 16”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adapter (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adapter (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adapter (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

EVIL ENERGY 6AN PTFE Hose End Fitting 90 Degree Black for PTFE Hose Only

  • Please Attention that the 6AN PTFE hose end can be work with PTFE fuel line ONLY..
  • Thread Size of 6AN PTFE Fitting is 9/16-18UNF and work with PTFE fuel line(Hose ID: 0.31 inch OD: 0.43-0.47 inch)..
  • The PTFE hose end is reusable, just  replace a new ferrule if you reinstall the fitting..
  • EVIL ENERGY Provide plently kind of fuel fittings, Swivel, push-on lock, PTFE hose end and other fitting adapters..
  • Warrany: EVIL ENERGY provide PTFE hose end 6-month warranty. We value your shopping experience and strive to offer a high-quality product and service..
Check Stock

Class A Customs | T-1000-BPK| 10 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 10 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-2100-BPK| 21 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 21 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34” Longest Length (not including fittings) x 9” x 16” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-4000-BPK| 40 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 40 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 13” x 18” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe....
Check Stock

Class A Customs | T-3000-BPK| 30 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male ....
Check Stock