Best Fiberglass Extension Ladders

Boxtown Team Ladder Carrier (XL Yellow)

Works on A-frame fiber glass Ladders 4ft-8ft and some aluminum..
Will work on 10ft-12ft A-frame fiber glass ladders,and most older EXTENSION fiberglass ladders but must FORCE FITTED..
Can carry ladder horizontal OR vertical. Open handle for multiple position carrying.
LARGER HANDLE SIZE FOR BIGGER HAND SIZES.

WORK SAFELY ON STAIRS: Ladder-Aide creates a STABLE and LEVEL surface for ladders on any staircase.
WORK FASTER: No installation required. Sets up in minutes. Moves easily from one stair to another.
USE ANY LADDER: Swap ladders instantly. Works with straight single, extension, and telescoping ladders.
FOR ALUMINUM LADDERS: Designed for Type 3 and 2 ladders. Check out Ladder-Aide Pro for fiberglass ladders.
MAX LADDER DIMENSIONS: 19 inch (48cm) base width, 4. 5 inch (11. 5cm) feet.
CHECK YOUR STEP SIZE: Ladder-Aide is compatible with steps between 5. 125″ and 7. 875″ high, and between 8. 268″ and 13. 975″ deep.

Designed to snap over extension ladder rail end caps.
Helps prevent damage to support surfaces.
Resists wear from paint, stains, thinner and solvents.
Fits all single and extension fiberglass and aluminum ladders except Werner 500, D500, D7136-2 and D7140-2.

Standards Compliance – Meets all ANSI and OSHA requirements for ladders up to Type 1A, 300 pound duty rating..
Ladder Compatibility – Fits most aluminum and fiberglass, extension ladders with open D or O rung holes on outside of ladder rail. Hole must have a minimum of 15/16 of inch clearance.
Installation Method – Attaches to ladder rail without fasteners. To attach, press 2 bracket ends in, toward each other, slide ends into rung holes and release.
Each bracket weighs 12.5 oz constucted with aluminum tube, 31/32” outside diameter.
Warranty – 24 months parts and labor for manufacturing defects.

PLEASE SEE VARIOUS MODELS AND SIZES IN COLOR SECTION. Works on A-frame fiber glass Ladders 4ft-8ft and some aluminum..
Will work on 10ft-12ft A-frame fiber glass ladders,and most older EXTENSION fiberglass ladders but must FORCE FITTED..
Can carry ladder horizontal OR vertical. Open handle for multiple position carrying..
Medium hand: 4 fingers fit. Large Hand: 3 fingers fit, but does not make difference using 3 or 4 fingers, weight isn’t on the pinky..

The Dark Horse is a multi-position ladder that converts to A-frame, extension, 90-degree, staircase and trestle-and-plank configurations..
Made from lightweight, non-conductive fiberglass for a safe climbing experience..
Wide-flared base increases the ladder’s side-tip stability..
Meets or exceeds all OSHA and ANSI standards..
This ladder has a Type IA 300 lb. rating..
Fewer shoulder and back injuries due to transport. Lighter than any other fiberglass articulating ladder.
Less lifting, fewer handling and transport-related injuries to the shoulder and back.
Prevent falls due to over-reaching. Wide-flared extension ladder improves side-tip stability.
Improvised solutions to uneven surfaces or are often dangerous and unstable. The Dark Horse adapts, offering a safe, stable climbing solution.
Replaces multiples sizes and types of stepladder and extension ladders.

Standards Compliance – Meets all ANSI and OSHA requirements for ladders up to Type 1A, 300 pound duty rating..
Ladder Compatibility – Fits most aluminum and fiberglass, extension ladders with open D or O rung holes on outside of ladder rail. Hole must be a minimum of 1″ in diameter..
Installation Method – Attaches to ladder rail without fasteners. To attach, press 2 bracket ends in, toward each other, slide ends into rung holes and release..
Bracket weight – Each bracket weighs 12.3 ounces.
This foam elbow material is for light duty, occasional use only. For heavier duty, longer lasting elbow material, Levelok offers the ST-ORS-3XL model..

For use with all Werner aluminum and fiberglass extension ladders.
(2) lock flippers, hardware, and instructions included.
Overall length of the flipper: 3″. The width at the mounting slot is 1″ on the outside, and 5/8″ on the inside, the length of the mounting slot is 1″..

For use with all Werner aluminum and fiberglass extension ladders.
(2) lock flippers, hardware, and instructions included.
Overall length of the flipper: 3". The width at the mounting slot is 1" on the outside, and 5/8" on the inside, the length of the mounting slot is 1"..

Hook Ladder and Roof Tightly: An ideal safer method to hook the ladder to the roof ridge tightly, more convenient, and safer checking the roof with this ladder hook..
Durable Material: Made of heavy-duty steel with water and rust-proof finish, Each ladder hook has 300 pounds bearing capacity, moreover the universal wheel makes it easier to slip the stair onto the roof, saving labor and time..
Thirdly, slide the ladder to the roof and fix it on the ridge of the roof, all in one minute.
The Werner ladder may need to modify for better fitting..
Compatibility: Fit for the ladders with rung clearance of 11’’ to 13.5’’.
Compatible with wood, fiberglass, or aluminum ladders.
Always install two ladder hooks per ladder, and roofs with vented ridges are not recommended to use.
NOTE: Please bolt or tie the two sections together of the extension ladder or just use it on the one section of the extension ladder when you use this product on your extension ladder..
What You Get: 1 set of Roof Ladder Hooks.
Welcome to contact us if you have any questions.

Props up your ladder around windows, rain gutters and more, so you can work around obstacles.
Adds stability when working in the extension position.
Hand-tightened screw clamp connects to ladder rung.
Compatible with most Little Giant aluminum and fiberglass articulating ladders.

Work safely on uneven ground. Extends a full 10..
Adapts to nearly any indoor or outdoor situation.
Meets or exceeds OSHA/ANSI requirements up to and including type 1AA (375lbs) ladders.
Triple plated pivoting foot with claw flips back for ice, snow, or gravel.
Fits aluminum, fiberglass, extension, combination, articulating, double sided step, sectional ladder.