Categories

Best Fired Heaters

HCLLPS Space Heater Replacement Parts PP236 Photocell For Reddy Remington Master Knipco Heaters M16656-24

  • Applications: For Desa Oil Heaters with Hot Surface Ignition (glow plug).
  • Space Heater Replacement Parts PP236 Photocell For Reddy Remington Master Knipco Heaters M16656-24.
  • PP236: Photocell Assembly should be used with 104068-02 ignition control boards on oil fired heaters..
Check Stock

new 102482-01/102482-04 Ignition Kit For Reddy Master DESA Kerosene HeatersOEM

  • Only works in 70-150K btu Desa oil fired heaters.
  • Brands include-Reddy, Remington, Master, Knipco.
  • only works in heaters that use the long spark plug..
Check Stock

Honeywell SV9641M4510 Upgraded Replacement for Furnace Smart Gas Valve

  • These controls communicate directly with an electronic fan timer (ST9160 Electronic Fan Timer for single stage applications.
  • ST9162 Electronic Fan Timer for two-stage applications) in typical forced warm air furnace applications.
  • It can directly interface with the appropriate power supplies and a system thermostat for additional appliance applications.
  • When controlled directly by a thermostat, these controls do not provide a post purge function, because power to the control is removed when the thermostat call for heat ends.
  • The Systems are suitable for a wide range of fan-assisted combustion gas-fired appliances including furnaces, rooftop furnaces, boilers, unit heaters, infrared heaters, water heaters and commercial cooking appliances.
Check Stock

ZFLXH Space Heater Replacement Parts PP236 Photocell For Reddy Remington Master Knipco Heaters M16656-24

  • ⭐PP236: Photocell Assembly should be used with 104068-02 ignition control boards on oil fired heaters..
  • ⭐This photocell is used with heaters that have the hot surface ignitor (glow plug). UNLESS you have the DESA upper tier heaters that have the plastic handle and shroud that covers the fuel tank. That photocell is part# M16656-21.
  • ⭐PINNACLE: ProTemp, Master, Remington, Heat-Stream, WorkHorse, Heat Hog & SunStream: (71-016-1010, 710161010).
  • ⭐DESA: Dayton, Knipco, Koehring, Master, Reddy, Remington, Sears, and TSC: (PP236, M16656-23, M1665623, M16656-24, M1665624).
Check Stock

PP205, HA3005 5/8\ Rotor Kit For Desa Reddy, Master Heater

  • PP236 Photocell Heaters Fits many Reddy, Desa models.
  • Photocell Assembly should be used with 104068-02 ignition control boards on oil fired heaters.
  • DESA: Dayton, Knipco, Koehring, Master, Reddy, Remington, Sears, and TSC: (PP236, M16656-23, M1665623, M16656-24, M1665624, M16656-21).
  • PINNACLE: ProTemp, Master, Remington, Heat-Stream, WorkHorse, Heat Hog & SunStream: (71-016-1010, 710161010).
  • Alternate #’s: (21925, 1PP236-MP4, 1PP236MP4).
Check Stock

Pro-Parts New Replacement PP236 Photocell Heaters for Reddy Remington Master Knipco DESA M16656-24

  • PP236: Photocell Assembly should be used with 104068-02 ignition control boards on oil fired heaters..
  • Apply to DESA: Dayton, Knipco, Koehring, Master, Reddy, Remington, Sears, and TSC: (PP236, M16656-23, M1665623, M16656-24, M1665624) PINNACLE: ProTemp, Master, Remington, Heat-Stream, WorkHorse, Heat.
  • This photocell is used with heaters that have the hot surface ignitor (glow plug). UNLESS you have the DESA upper tier heaters that have the plastic handle and shroud that covers the fuel tank. That photocell is part# M16656-21.
  • A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable)..
Check Stock

Stanbroil 90° Elbow Connector Replacement for Olympian Low Pressure Gas Fired Heaters - 3/8 Female Flare x 3/8 Male Flare

  • Perfect for use with the Wave 3, or catalytic safety heaters..
  • For use with our Olympian low pressure gas fired heaters..
  • The elbow is able to provide easy installation..
Check Stock

Warren Distribution Blaster Penetrating Catalyst, 11 Ounce - 12 per case

  • Ceramitation is a remarkably versatile decorative enamel with a finish that is virtually equivalent to hard-fired enamel.
  • The hardness of cured Ceramitation is 60 to 75 on the Sward scale, as compared to Kiln fired enamel at 65 to 80.
  • Ceramitation features rich-warm colors, and is an excellent spraying medium – Thinner is available for this method of application.
  • Only 30 to 45 minutes at a maximum curing temperature of 250ºF (120ºC) is required.
  • Temperature controlled ovens, infrared lamps, or portable electric heaters may be used.
Check Stock

102482-01 102482-04 Ignition Kit For DESA Reddy Master Kerosene Heaters

  • Only works in 70-150K btu DESA oil fired heaters that used spark plug.
  • Brands include-Reddy, Remington, Master, Knipco.
  • Brands include- Dayton, Deere, Koehring, Co-op.
Check Stock

70-052-0200 spark plug ProTemp for Remington Master HeatStream 120k-215k btu

  • This 70-052-0200 ignitor/spark plug is used on 125k, 175k, 215k and 400k btuoil fired heaters made by Pinnacle.
  • 70-052-0200 spark plug ProTemp, for Remington, Master, HeatStream 120k-215k btu.
  • ProTemp: PT-125T-KFA, PT-175T-KFA, PT-215T-KFA HeatHog/Remington: HH-125T-KFA, HH-175T-KFA, HH-215T-KFA Master: MH-125T-KFA, MH-175T-KFA, MH215T-KFA....
Check Stock

American Standard CE-12-AS 12 gallon Point of Use Electric Water Heater

  • Inner Dura glas lined tank fired at 1,600°f for optimum protection from the effects of corrosion.
  • Factory installed Brass drain valve on all models allows for easy draining of the unit which reduces sediment deposits extending tank life.
  • Factory installed Brass temperature/pressure relief valve.
  • American standard point-of-use electric water heaters are all certified at 300 psi test pressure and 150 psi working pressure. All tanks are also 100% hydrostatically tested at the factory.
Check Stock

American Standard CE-20-AS 19 Gallon Point Of Use Electric Water Heater

  • Inner Dura glas lined tank fired at 1,600°f for optimum protection from the effects of corrosion.
  • Factory installed Brass drain valve on all models allows for easy draining of the unit which reduces sediment deposits extending tank life.
  • Factory installed Brass temperature/pressure relief valve.
  • American standard point-of-use electric water heaters are all certified at 300 psi test pressure and 150 psi working pressure. All tanks are also 100% hydrostatically tested at the factory.
Check Stock

American Standard CE-6-AS 6 gallon Point of Use Electric Water Heater

  • Inner Dura glas lined tank fired at 1,600°f for optimum protection from the effects of corrosion.
  • Factory installed Brass drain valve on all models allows for easy draining of the unit which reduces sediment deposits extending tank life.
  • Factory installed Brass temperature/pressure relief valve.
  • American standard point-of-use electric water heaters are all certified at 300 psi test pressure and 150 psi working pressure. All tanks are also 100% hydrostatically tested at the factory.
Check Stock