Categories

Best Fitting Hose

Class A Customs 13 Gallon Water Tank & Plumbing Kit T-1300-BPK

  • ...Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • 13 GALLON TANK MEASUREMENTS 21” x 9” x 16”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adapter (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adapter (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adapter (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

POWERTEC 70175 Dust Collection Hose with Fittings Plus Two Reducers , Black

  • ...to connect your shop vac or 2-1/2” dust collection system to a 1-1/2” tool port, an additional 1-1/2” screw on adapter, Powertec 70296, is available. Simply remove the 1”ID adapter and replace it with the additional 1-1/2” ID adapter.
  • INCLUDES: (ONE) 10ft dust collection hose, (ONE) 1" pliable plastic hose fitting, (ONE) 1-1/2" pliable plastic hose fitting, (ONE) 2-1/4" ABS dust hose adapter, and (ONE) 2-1/2" ABS dust hose adapter.
  • APPLICATION: Allows you to extend the reach of your shop vacuum or dust collecting power tools with a long, flexible and premium quality vacuum hose that is free roaming and able to suck up dust, dirt and debris.
  • VERSATILE: Offers a dust collection power tool hose with fittings that work with most small vacuums, shop dust collection systems, orbital sanders, joiners, jigs and other power tools. The nominal 2-1/4” adapter should fit most shop vac ports with a nominal ID of 2-1/4”. Shop Vac ports sizes can vary between different manufacturers. Please refer to the actual adapter sizes before ordering, to verify that it will work for your application.
  • DIMENSIONS: Dust collector hose 1-3/16" O.D x 10ft long | ABS vacuum dust hose adapter nominal 2-1/2" O.D actual 2-27/64”| ABS vacuum dust hose adapter nominal 2-1/4"....
Check Stock

Class A Customs | T-1000-BPK| 10 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 10 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 19” Longest Length (not including fittings) x 9” x 14” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-2100-BPK| 21 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 21 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34” Longest Length (not including fittings) x 9” x 16” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thre....
Check Stock

Class A Customs | T-4000-BPK| 40 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 40 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 13” x 18” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe....
Check Stock

Class A Customs | T-3000-BPK| 30 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male ....
Check Stock

Boltigen Pressure Washer Swivel Fitting, Anti Twist 3/8 NPT Male to Female Stainless Steel Connector Joint, 360 Degree Kink Free Swivel Fitting (3/8 NPT Male to 3/8 NPT Female-1Pc)

  • 【Swivel Fitting】 Kink free Swivel Joint for pressure washer with 3/8'' NPT male and female thread fitting，connects hose to hose or gun to hose..
  • 【Smart Design】 Pressure washer swivel joint with 360 degree rotation, eliminates twists and kinks on working, reduces stress on not only hose and gun, but also operator..
  • 【High Working Pressure】 Working pressure of washer gun fitting is up to 4500 PSI and working temperature is up to 250 °F, suitable for hot and cold water. Pressure washer fitting is made of high quality stainless steel, resistance to corrosion and long life using. Max Flow Rate: 30.0 GPM..
  • 【Application】 Suitable for connect swivel fitting between gun and hose, Swivel fitting rotates freely, reduces the strain on your wrist when using the pressure washer..
  • 【Quality Warranty】 The stainless steel pressure washer swivel joint for your pressure washer gun and hose. We did 100% inspection before goods leave our factory, if you have any problem with these products, we will 100% refund to you or replace a new set for you..
Check Stock

Class A Customs | Under Mount 20 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit UM-2000-BPK

  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 13” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Th....
Check Stock

Class A Customs | Under Mount 30 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit | UM-3000-BPK

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 20.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES: (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5”....
Check Stock

RIDGE WASHER Pressure Washer Gun with Extension Wand for Hot and Cold Water, Power Washer Gun with M22 Fitting, 5 Nozzle Tips, 40 Inch, 4000 PSI

  • Power washer gun is designed for hot and cold water in gas and electric pressure washer. Max Temperature for water is up to 100℃ ( 212°F ). Max Flow Rate is up to 5.3 GPM. Max Pressure is up to 4000 PSI..
  • This pressure washer wand fits pressure washer hose with M22 14mm or M22 15mm fitting. Generac, Ryobi, Briggs Stratton, Craftsman, Simpson, Karcher pressure washer hose has M22 14mm fitting. Sun Joe, Excell, MI-T-M, Stanley, Campbell, AR Blue, Cleanforce, Simoniz power washer hose has M22 15mm fitting. Please connect power washer wand to the hose directly if your hose has M22 14mm fitting. Please connect brass coupler between wand and hose if your hose has M22 15mm fitting..
  • The length of pressure washer handle is adjustable. Easy to change the length based on the purpose of cleaning. There are three length, 40 inch, 24 inch, 9 inch..
  • 5 spray nozzles have different spray angle (0, 15, 25, 40, 65 degree). Choose suitable nozzle based on the purpose of cleaning. Such as watering flowers or plants, washing car, fence or roof. Universal 1/4’’ quick connector is also designed for turbo nozzle, surface cleaner, water broom, undercarriage cleaner, pivoting coupler, foam cannon, pressure washer sandblasting kit, gutter cleaner attachment..
Check Stock

PWACCS Pressure Washer Swivel, M22 14mm Swivel Joint, Stainless Steel, 5000 PSI

  • UNIVERSAL CONNECTORS: Pressure washer swivel convert metric M22 14mm male to M22 female thread fitting. Easy to connect and release. Pressure washer swivel joint can connect gun and hose, hose and hose easily. Pressure washer fittings fit most brand of pressure washer hoses and guns..
  • 360 degree rotation freely, pressure washer swivel fitting helps keep the pressure washer hose from tangling and getting kinked when Spraying. The kinks unfolding as you move around. It will solve hand fatigue due to the pressure built up between hose and gun..
  • Pressure washer gun swivel is made of high quality stainless steel, durable, wear resistantand, resistance to corrosion, long service life..
  • Pressure washer hose swivel’s Max Working Pressure: 4500 PSI. Max Flow Rate: 30.0 GPM. Max Working Temperature: up to 120℃, 250°F..
  • If the Kink free gun to hose fitting have any questions, please contact us at first time. We provide a service of quick reply within 24 hours..
Check Stock

Bonbo Fuel Gas Cap with Brass Hose for Honda EU2200i EU1000i EU2000i EU3000i Handi, Champion 2000watt, Westinghouse 2200watt WH2200iXLT Generators, Upgrade Extended Run (Red)

  • Application - This fuel gas cap can be widely used in Honda EU2200i EU1000i, EU2000i, EU3000i Handi, Champion 2000watt, Westinghouse 2200watt WH2200iXLT generators..
  • Function - As a fixed connection between plastic or rubber hose and pipe, this gas cap with brass hose fitting helps you add gasoline into generator within a safe distance, ensuring seal tight and no leakage..
  • Design - The brass hose fitting has a 1/4" male end for connecting to threaded pipe, conforming to National Pipe Thread (NPT) standard and the barbed fitting for a hose is equipped with a 1/4" inside diameter..
  • Material - The gas cap is made of premium CNC billet aluminum, finishing with stylish anodized red coat. And the hose fitting is made of top high quality and wear resistance brass, performing well even under extreme conditions..
  • Satisfaction Guarantee - Bonbo aims to provide best products and services for our customers. If you receive broken or defective gas cap and brass hose fitting, please contact us any time, we will compensate you with 1 year warranty or 30 days full refund..
Check Stock

EVIL ENERGY 6AN PTFE Hose End Fitting 90 Degree Black for PTFE Hose Only

  • Please Attention that the 6AN PTFE hose end can be work with PTFE fuel line ONLY..
  • Thread Size of 6AN PTFE Fitting is 9/16-18UNF and work with PTFE fuel line(Hose ID: 0.31 inch OD: 0.43-0.47 inch)..
  • The PTFE hose end is reusable, just  replace a new ferrule if you reinstall the fitting..
  • EVIL ENERGY Provide plently kind of fuel fittings, Swivel, push-on lock, PTFE hose end and other fitting adapters..
  • Warrany: EVIL ENERGY provide PTFE hose end 6-month warranty. We value your shopping experience and strive to offer a high-quality product and service..
Check Stock