Best Flywheel Bolt Kit

XianFeng 22100 Flywheel Locking Tool for 6.6L Duramax Engine with 36mm 3/4 Inch Wench

• Work on Duramax 2500 / 3500 pickups .Remove metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel..
• Locking the flywheel at the transmission instead of having to remove the starter for water pump replacement..
• Toothed pieces with screws---Remove the rubber inspection cap on the bottom of the transmission.Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place..
• Forged 36mm socket---Use on the balancer bolt.Use with a 3/4" square drive wrench.
• Quality tool ---Made of CRV steel with durability, flywheel locking tool is anti-rust and corrosion-resistant.

Bolaxin Flywheel Locking Tool with 36mm 3/4 Inch Wench for 6.6L Duramax Engine

• Locks Flywheel in Place When Removing Harmonic Balancer on 6.6L Duramax Engines with Allison Automatic Transmissions.
• Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement.
• Use 36mm 12-point socket with 3/4 square drive to remove harmonic balancer bolt and retorque on installation.
• Duramax 2500 / 3500 Pickups – Use toothed pieces only removes metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel..
• Duramax 4500 / 5500 Trucks -- Use toothed pieces with screws remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place..

Schaeffler LuK DMF123 Dual Mass Flywheel, OEM Dual Mass Flywheel, LuK Replacement Clutch Parts

• OEM Clutch Replacement Kits: Our LuK DMF123 dual mass flywheels suit a huge variety of vehicles! The flywheel is an integral part of your clutch replacement..
• Replacement Flywheel: Today’s tightly packaged clutch systems leave little room for error. The clearance between the disc damper and the flywheel-to-crankshaft bolt heads is so small that the flywheel must be replaced with every clutch installation..
• LuK Flywheel: The dual-mass flywheel absorbs engine vibrations before they are transmitted to the driveline where they can rattle gears. It has a primary section that bolts to the crankshaft, and a secondary section, which the clutch is bolted onto..
• Dual Mass Flywheel: The primary section of the LuK DMF dampens, isolates engine vibrations and prevents engine torque spikes from damaging the transmission. By design, dual-mass flywheels cannot be resurfaced..
• OEM Flywheel: As an original-equipment supplier, LuK develops the performance specifications for individual vehicle applications. Each OEM part is carefully crafted to suit the exact needs of a car, keeping in mind....

Auto Body Now ABN Harmonic Balancer Puller 46-Piece Tool Kit – Flywheel Remover, Crankshaft Pulley Removal, Steering Wheel Pulling Set

• [Effortlessly Remove Harmonic Balancers] Use the ABN 46 Piece Harmonic Balancer Puller Kit - Flywheel Puller, Crank shaft Pulley Puller, Steering Wheel Puller Set to apply even pressure to the hub so you can safely remove harmonic balances and other vehicle parts.
• [Fits your Vehicle Needs] Steel yoke with 4 slots and 30 harmonic balance puller bolts allow you maximum versatility to handle a range of jobs on most cars, trucks, SUVs, and small engine vehicles.
• [Various Bolt Sizes] 3/8-inch bolt in 1-1/2, 2, 4.5, and 6 inch lengths, 5/16-inch bolt in 3, 3.5, and 6-inch lengths, 1/4-inch bolt in 2.5-inch length, M8 x 1.25mm bolt in 45, 65, and 90mm lengths, and M10 x 1.5mm bolt in 35mm length.
• Bolts come in a mixture of 16, 18, 24, and 28 thread pitch.
• [Built to Last] Heat-treated carbon steel ensures maximum strength.
• Chrome and black oxide finishes resist rust and corrosion.
• Heavy-duty blow-molded carrying case provides easy transportation, safe storage, and quick organization.
• [Package Contents] Crank pulley puller tool wheel balancer gear puller set include (1) 5 inch long 3/4-inch....

ATPEAM 46pcs Harmonic Balancer Puller Set | Steering Wheel Puller Kit, Use with Harmonic Balancers, Crankshaft Pulleys and Gears, Work on Most Cars, Pickups, SUVs

• Extra Last: The Steering Wheel Puller Kit is made of heat-treated carbon steel ensures maximum strength.
• Chrome and black oxide finishes resist rust and corrosion.
• Heavy-duty blow-molded carrying case provides easy transportation, safe storage, and quick organization.
• Mutiple Use: The harmonic balancer puller includes 30 different bolts&a four yoke slot, allowing unit to be used with harmonic balancer, Flywheel, Crankshaft, Steering Wheel ,Pulley and other two or three-hole applications..
• Various Bolt Sizes Added: 3/8-inch bolt in 1-1/2, 2, 4.5, and 6 inch lengths, 5/16-inch bolt in 3, 3.5, and 6-inch lengths, 1/4-inch bolt in 2.5-inch length, M8 x 1.25mm bolt in 45, 65, and 90mm lengths, and M10 x 1.5mm bolt in 35mm length.
• Bolts come in a mixture of 16, 18, 24, and 28 thread pitch.
• Wide Compatibility: The ATPEAM crankshaft pulley puller features a steel yoke with four slots enabling use on nearly any vehicle configuration..
• The Wheel Balancer Gear Puller Set Includes: (1) 5 inch long 3/4-inch pressure screw, (30) bolts, (1) steel yoke, (2) centering adapters, (1) flat shaft adapter, (11) different sized washers, and (1) carrying case for your convenience.

Valeo 52151203 Solid Flywheel Conversion Kit Compatible with Select Mini Cooper Models, 2002-2008

• The same installation time as a Dual Mass Flywheel kit - no special tools required..
• All new components provide better thermal resistance and full engine gearbox protection.
• The lightweight kit increases torque transfer efficiency and reduces torsional stress on the crankshaft.
• Notably reduces the cost of repair when compared to the DMF Kit.
• Kit contains everything needed to complete the job: Rigid flywheel, flywheel bolts, long travel damper disc, cover assembly, pressure plate bolts, release bearing or CSC and centering tool (available for most popular items).

Valeo 52285615 Solid Flywheel Conversion Kit Compatible with Select Audi and Volkswagen Models

• The same installation time as a Dual Mass Flywheel kit - no special tools required..
• All new components provide better thermal resistance and full engine gearbox protection.
• The lightweight kit increases torque transfer efficiency and reduces torsional stress on the crankshaft.
• Notably reduces the cost of repair when compared to the DMF Kit.
• Kit contains everything needed to complete the job: Rigid flywheel, flywheel bolts, long travel damper disc, cover assembly, pressure plate bolts, release bearing or CSC and centering tool (available for most popular items).

Valeo 52285616 Solid Flywheel Clutch Conversion Kit Compatible with Select Volkswagen Jetta Golf Beetle and Rabbit Models

• The same installation time as a Dual Mass Flywheel kit - no special tools required..
• All new components provide better thermal resistance and full engine gearbox protection.
• The lightweight kit increases torque transfer efficiency and reduces torsional stress on the crankshaft.
• Notably reduces the cost of repair when compared to the DMF Kit.
• Kit contains everything needed to complete the job: Rigid flywheel, flywheel bolts, long travel damper disc, cover assembly, pressure plate bolts,....

Mopar Bolt Hex Head - 6504383

Lisle 22100 Flywheel Locking Tool for 6.6L Duramax

• Locks flywheel in place when removing harmonic balancer on 6.6L Duramax engines with Allison automatic transmissions.
• Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement.
• Use 36mm 12-point socket with 3/4 square drive to remove harmonic balancer bolt and retorque on installation.
• Package dimension is 4.5 inches width by 5 inches height by 2 inches depth.

Valeo 52255602 Solid Flywheel Conversion Kit

• Provides a high performing and efficient solution for replacing the dual mass flywheel (DMF), this innovative solution replaces the DMF with a solid....
• Premium Friction Material for Increased Durability: Valeo's enhanced F510 friction material is composed of an organic compound and higher copper....
• Consistent Driver Comfort: The long travel damper technology consists of a specific friction plate with a higher damper capacity for improved....
• Maximum Torque Transfer: Due to the flywheel's solid composition, combined with the increased clamp load of the Clutch Cover (Pressure Plate), this....
• Simple Bolt-on Installation: No special tools or pre-loading required.

Zinger Mercury Mariner Force Yamaha 1 1/2' -16 Flywheel Puller Removal Tool 91-849154T1

• For Mercury Mariner Force Yamaha Flywheel Puller with crank shaft protector 91-849154T1.
• For Most 45HP+ Mercury, Mariner, Force and Yamaha outboard motors with 1 1/2"-16 TPI threads units from the 1960s to present,but pls check thread diameter to verity.
• Warm tips: please apply some lube oil on the flywheel and puller tool before use it.Thank you !.

NEW RAM 11" CLUTCH & BELLHOUSING KIT WITH GM 621 3899621 ALUMINUM BELLHOUSING, FLYWHEEL INSPECTION COVER, CLUTCH FORK BOOT & CLUTCH PIVOT BALL, PRESSURE PLATE, 26 SPLINE DISC, FLYWHEEL, SBC BBC CHEVY

• Brand New Southwest Speed and Ram Clutch Aluminum Bellhousing and 11" Clutch Kit for use with Manual Transmissions. The kit includes a replica GM 3899621 Bellhousing, Flywheel Inspection Cover, Clutch Fork with Ball Retaining Spring, Throwout Bearing, Clutch Fork Boot, Clutch Fork Pivot, Flywheel, Clutch Disc, Pressure Plate, and hardware (Part # 650-39755, 901180) > Fits transmissions with 1 5/32"-26 spline input shafts and Chevy engines with a 2 piece rear main seal.
• The Southwest Speed 11" Performance Cast Aluminum Bellhousing is a reproduction of the original 3899621 bellhousing used on GM models with Big Block and Small Block engines > This performance aluminum bellhousing does not have the GM Part # 3899621 casting number but will look, fit, and perform just like original > If you are doing a restoration of an early muscle car, or just want the correct bellhousing to finish that rod project, this bellhousing is the perfect part.
• Fits: > 1964-1988 Chevy Chevelle, Malibu, Monte Carlo* > 1959-1987 Chevy El Camino* > 1959-1988 Chevy Impala, Caprice, Bel Air, Biscayne, Brookwood, Kingswood, Nomad, Sedan Delivery* > 1963-1981 Chev....