Best High Helix End Mills

YG-1 EH970 Carbide Square Nose End Mill, Long Reach, TIALN Multilayer Finish, Roughing Cut, 45 Deg Helix, 4 Flutes, 2.5\ Overall Length, 0.25\ Cutting Diameter, 0.25\ Shank Diameter

• Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills.
• Fine-pitch tooth design and tool geometry are suitable for machining steel up to Rockwell hardness C45, stainless steel, titanium alloys, and nickel-based alloys.
• Long-reach end mills have an extended shank for access to recessed areas of the workpiece.
• Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than TiN and TiCN coatings.
• Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures.

HHIP 3900-1005 5-Piece R8 End Mill Holder Set, 3/16-3/4'

• 5 PC SET 3/16, 3/8, 1/2, 5/8, 3/4" DRAWBAR END THREAD: 7/16" -20.
• Hardened and ground For Bridgeport type milling machines.
• Hardened and ground. For double and single end mills (single end mils only for sizes over 5/8").
• 5 PC SET For Bridgeport type milling machines. DRAWBAR END THREAD: 7/16" -20.
• For double and single end mills (single end mils only for sizes over 5/8").

ACCUCUT I4KES 3/16 Carbide End Mill, 4 Flute, Square End, Ideal for Steel, Forge Steel, Copper and Alloys, 45 Degree Helix (5 Pieces)

• GENERAL USAGE：Our end mill can be applied for steel, forge steel, copper, alloys & material < HRC 50.
• SOLID CARBIDE：This end mill is made of ultra fine grain tungsten carbide. The hardness is 92 HRA.
• AlTiCrN COATING：it features tough, resists wear & lubricity for smooth surface and heat protection.
• 4 FLUTE CUTTER：great for speedy cutting. Ideal for planar, step, groove, forming surface & more.
• 45° HELIX：high helix design can perform a better finishing cut than those with lower helix degree.

LittleMachineShop.com 4 Flute Ball End Mill Set, High Speed Steel, 6 Piece (2903)

OSCARBIDE Carbide Inserts APKT1604 TiAlN Coated Indexable Milling Inserts APKT Style,10 Piece/Box

• APKT 1604 carbide turning inserts,85 degrees parallelogram,Relief Angle 11 degrees,nose radius 1/32"..
• Made of Tungsten Carbide,TiAlN Coated ,the cutting speed are 4-7 time faster than generic steel,and Sharpened on a diamond wheel to make it longer tool life, providing you a better experience and durable use and Better cut.
• Designed for cast iron and non-ferrous materials,good for both finishing and roughing.
• Used for indexable face mill and end mill,Performing square milling and side milling,ramping milling, helical milling, slotting milling, plunging milling..
• These Insert fit for our Carbide Indexable End Mills and other same size indexable end mills, please search B07SG8JKDS or B099WPXW29 to buy this indexable end mills.

LittleMachineShop.com #3 Morse Taper End Mill Holder Set, 5 Piece (1636)

• Set of five 3 Morse taper end mill holders.
• Compatible with Mills with 3 Morse Taper Spindle.

LittleMachineShop.com R8 End Mill Holder Set, 5 Piece (1258)

• Set of five R8 end mill holders from 3/16" to 3/4".

Kodiak Cutting Tools L3-OFFT-21LF USA Made Micrograin Carbide Ball Nose End Mill Set, 4 Flute, 1/8\ to 1/2\ (Pack of 6)

• Contains Kodiak Cutting Tools brand premium quality USA made ball nose solid carbide end mills.
• 4 flute ball nose end mills are center cutting and made from premium sub-micrograin carbide.
• Stub length end mills for extra rigidity.
• Fitted wood block stand included and each size comes in a marked plastic tube.
• Contains 1pc of each diameter: 1/8, 3/16, 1/4, 5/16, 3/8 and 1/2.

Genmitsu 4pcs 2-Flute Tapered Ball Nose End Mills Tungsten Carbide Cutter with Nano Blue Coat R0.25-1.0 1/8” Shank TB04A

• High Quality: The Genmitsu end mills are made of ultra-fine 0.2μm tungsten carbide steel alloy that can keep continuous machining 800 minutes. Moreover, its Nano Blue Coating with high hardness and heat resistance enables the tool's cutting edge to retain crucial sharpness and lubricity. This provides longevity and produces cutting results of the highest quality..
• Cost-Effective: Coming with 4x 2-Flute tapered ball nose end mills, Shank Diameter: 3.175mm, Radius: 0.25, 0.5, 0.75, 1.0mm, Cutting Length: 15mm, Overall Length: 40mm..
• Versatile: Perfect for 3D machining jobs like molds, rapid prototyping, models and other other precision parts processing, these Tapered ball nose bits can do the best..
• Applicable Materials: These nano blue coating bits have an HRC rating of 65 and are optimal for milling a wide range of materials, including plastics, aluminum, circuit board, wood, etc. To learn more about how to choose the right bits to meet your needs, please find the Comparison Chart (CNC Bits Buying Guide) at the Product Guides and Documents Section below..
• Wide Compatibility: Genmitsu TB04A tapered ball nose end mills are compatible with most desktop CNC machines, such as the Genmitsu 3018 Series, as well as other industrial CNC machines. Just make sure ....

Genmitsu 40pcs End Mills CNC Router Bits, 1/8\ Shank CNC Cutter Milling Carving Bit Set Including 2-Flute Flat Nose & Ball Nose End Mill, Nano Blue Coat & Titanium Coat CNC Bits, MC40A

• High Quality: The Genmitsu end mills are made of ultra-fine 0.2μm tungsten carbide steel alloy that can keep continuous machining 800 minutes. Moreover, its Nano Blue Coating /Titanium Coating with high hardness and heat resistance enables the tool's cutting edge to retain crucial sharpness and lubricity. This provides longevity and produces cutting results of the highest quality..
• 2-Flute Spiral Flat Nose & Ball Nose End Mills -- Shank Diameter: 3.175mm, Cutting Diameter: 3.175mm, Cutting Length: 17mm, Overall Length: 38mm..
• Two End Mill Sets -- Shank Diameter: 3.175mm, Cutting Diameter: 0.8 - 3.0mm (0.8/1.0/1.2/1.4/1.6/1.8/2.0/2.2/2.5/3.0mm), Cutting Length: 17mm, Overall Length: 38mm, with Nano blue and Titanium coating..
• Applicable Materials: Widely used in various materials including plastics, aluminum, circuit board, wood, as well as other precision parts processing. To learn more about how to choose the right bits to meet your needs, please find the Comparison Chart (CNC Bits Buying Guide) at the Product Guides and Documents Section below..
• Wide Compatibility: The MC40A end mills are compatible with most desktop CNC machines, such as the Genmitsu 3018 Series, as well as other industrial CNC machines. Just make sure you select the correct-sized co....

Niagara Cutter 17005489 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 4' Overall Length, 0.375' Cutting Diameter, 0.375' Shank Diameter

• 4 flute design for creating finer finishes and a higher metal removal rate.
• General purpose end mill for working on all types of materials.
• Made of extra-fine grade carbide for ultra high transverse rupture strength.
• Uncoated end mills feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
• Center Cutting End Mills are designed with "End Teeth" making these ideal for Slotting and Cavity applications.

CNC Router Bits 1/8' Shank Ball Nose Carbide End Mill Two Flute CNC Spiral Bits Upcut Cutter 3.175mm Carbide End Mill for Alloy Steels/Hardened Steels 10pcs (3.175x32x55mm)

• DIMENSIONS: 1/8" (3.175mm). Cutting edge diameter, 1/8" (3.175mm). Cutting edge length/flute length, 1/2"(12mm). Overall length, 1-1/2"(38.5mm)..
• Range of processing：Ball end mills can mill die steel/cast iron/carbon steel/alloy steel/tool steel/ general iron. Ball nose milling cutters can work normally in high temperature environments..
• High efficiency：Ball nose carbide end mill is a double-blade with helical design, and the large and uniform pin-out groove is conducive to high-speed machining. The sharp double edge can effectively improve the cutting efficiency of the tool..
• Perfect cutting：The ball mill design of the double-blade ball end milling cutter effectively reduces the burr and increases the wear resistance of the tool..
• Ball Nose End Mills are Suitable for Side Milling, End Milling, Finish Machining, etc..

Humminbird 720108-1 14 M360 2DDI Y MEGA 360 & 2D/MDI Y Cable

• Compatible with: MEGA 360, SOLIX 15 MSI G2, SOLIX 15 MDI G2, SOLIX 12 MSI G2, SOLIX 12 MDI G2, SOLIX 10 MSI G2, SOLIX 10 MDI G2.
• Combines MEGA 360 Imaging transducer and 14-pin Dual Spectrum / MEGA Imaging+ transducers (including Built-in MEGA Imaging) into one 14-pin plug for connection to the same, compatible SOLIX fish finder, or HELIX fish finder with additional AD HELIX M360 adapter..
• For use when connecting a MEGA 360 Imaging transducer to a compatible SOLIX or HELIX fish finder, in conjunction with a Built-in MEGA Imaging transducer or external 14-pin 2D /MDI transducer..
• If this cable is being used with a HELIX fish finder, then the #720109-1 AD HELIX M360 adapter must be attached between this y-cable and the HELIX unit, to the single plug end of the Y cable..