Categories

Best Hole saw Drill Bit

4 Inch Carbide Hole Saw Bit Concrete Hole Saw for Dryer Vent and Drywall for Recessed Lighting 102mm Carbide Hole Cutter for Stucco Brick Fiberglass Reinforced Plaster Ceramic Tile and Cement blocks

  • 102mm 4" CARBIDE GRIT HOLE SAW For Drilling Holes In Tough To Drill Materials, Regular Toothed Hole Drill Bit Would Go Dull If Used As A Drywall Hole Saw But With Carbide Tipped Tool Bits They Are Tougher And No Teeth To Snag And Go Dull..
  • TUNGSTEN CARBIDE GRIT Hole Saws Are Professional Tools Construction Tools Electrician Tools And Plumbing Tools Whether It Be For Diy Home Improvement Or Remodelling. Drill Holes Through Brick Walls To Run Conduit For Electric Cables And Pvc Water Pipes And Waste Pipes..
  • TILE HOLE SAW Drill Ceramic Wall Tiles And Low Density Subway Tile Without Hammer Drill Setting, When Used As Concrete Tools Hammer Drill Is A Must So The Tct Hole Saws Are Best Used With Our Hole Saw Abors That Already Come With Tct Masonry Drill Bits For Pilot Bit No Point Having A Hole Saw That Can Cut Holes In Brick If The Pilot Drill Set Will Not..
  • MANY SIZE GRIT HOLESAW BITS Available Either As Carbide Hole Saw Kit Or Individually From 5/8 16mm To 7" 178mm, These Tungsten Holesaw Bits Are Also Available Including Hex Hole Saw Arbor Or Including Sds Plus Hole Saw Arbor Mandrel inc TCT Pilot.
  • WHO USES OUR CARBIDE HOLE SAWS Plumbers Electricians Contractors for Masonry Tools Home Builders Boat Builders Aviation FiberGlass Car Body Installers Fib....
Check Stock

zerotop Diamond Drill Bits with Hole Saw Guide 16Pcs Hole Saw Set with Triangle Drill Bit Set & Screwdriver Suitable for Ceramic, Glass, Tile, Marble Porcelain

  • ...-grade carbon steel and has a long service life. It has a nickel-plated coating to resist corrosion, wear resistance, durability. Each hole is smooth and precise surface treatment, and the top is thickened with diamond to achieve excellent cutting strength..
  • 【Large Clearance Hole】The large clearance holes of the drill bit help the cooling water to enter and flush particles such as chips, reducing drilling resistance. When the debris is stuck in the small hole saw, you can use the equipped screwdriver to pull it out to make the drilling process smooth and easy..
  • 【Adjustable Drill Guide】The minimum and maximum opening lengths of the adjustable hole saw guidance fixture is 4mm/0.16in and 84mm/3.3in respectively, which can fix hole saws of any size. The diamond drill bit set has two modes (fixed 3 or 4 bearings) for your choice. You take off the two big nuts and install the chassis in reverse, and install one of the bearings to the center to form a three-bearing..
  • 【Wide Usage】The diamond hole saw drill bit set is very suitable for removing rings on marble, tiles, glass, ceramics, PVC or other materials. It is the excellent choice for your home decoration, DIY creation, wine bottle craft and so on..
  • 【You Can Receive】The package includes 10 dia....
Check Stock

Rannb Wood Auger Dill Bit Door Lock Installation Kit Door knob hole saw Door latch hole saw

  • 【Function】Used for larger lock hole and a auger bit for latch hole..
  • 【Accurately Drill】Pricise boring for door is assured with four edged hole saw and pilot drill bit..
  • 【Completed Kits】Cut type hole saw with a mandrel bit is for larger lock hole. Wood Auger Bit is for latch hole..
  • 【Package Content】1pcs x Hole Saw + 1pcs x Auger Bit + 1pcs x L Shaped Mandrel Bit.
  • 【Please Attention】This Door Lock Installation Kit is only used on wood doors..
Check Stock

4 inch Deep Hole Saw Carbide, 2.36” Cutting Depth for Multiple Material Hardy Plank MDF Wall Tile 10X More cuts 5X More Faster

  • 1, The Carbide Tipped Teeth hardness HRC overs 80. It’s more hard, more shape, longer life. Up to 10X times more Cuts than standard bi-metal hole saw drilling for Hardy plank. Up to 5X times more Speed than standard bi-metal hole saw drilling for Hardy plank..
  • 2, The big slot design is to remove the plug easily. Up to 5 times Faster than standard hole saw..
  • 3, Max cutting depth:2.36 “( 60mm) . Replaced the following drill bits: Spade bit, Forstner bit, Auger bit, bi-metal hole saw..
  • 4, Ideal drilling for multiple materials: Hardy Plank, Hard wood（not with nail), Drywall, MDF, Fiberglass, Wall Tile, Air Brick, Plasterboard. Cutting material MOHS hardness ：Not up to 6 . For use in standard rotary drills. Not for use in Hammer mode..
  • 5，This carbide hole saw cutter includes: 4”(102mm) carbide tipped hole saw , 1 of 0.34”(8.6mm) hex shank arbor, 1 of Ø1/4”x4.3”(110mm) silver HSS pilot drill bit for wood. 1 of Ø1/4”x4.3”(110mm) carbide tipped pilot drill bit for hardy plank, stone, wood..
Check Stock

Rannb 90mm/3.5' Hole Saw for Cutting Wood Plywood Laminated PVC Board

  • ⭐【Material】Features heat treated carbon steel alloy hole saw blade, non-binding clean edge design.The blade is sharp with high hardness..
  • ⭐【Dimension】Cutting Dia: 90mm /3.5".
  • ⭐【Application】This Hole Saw Drill Bit is designed for wood / plastic cutting.
  • It can effectively and economically cuts a wide variety of materials including aluminum, iron and wood..
  • ⭐【Convenience】The spring on the drill bit is nice because it automatically pushes the disc out of the saw immediately after completing the hole..
  • ⭐【Package Content】1pcs x Shank + 1pcs x Hole Saw + 3pcs x Pilot Drill Bit + 1pcs x Small L Wrench.
Check Stock

4 Inch Diamond Drill Bits Glass Hole Saw Drill Bit Set for Glass Ceramics Porcelain Ceramic Tile Marble

  • SMALL DRILL BIT: Hole diameter: 100mm(4"),total length: 56mm(2.2").Package includes 1 pcs 100mm diamond hole saw drill with a transparent box..
  • HIGH QUALITY: Diamond ceramic hole saw are made of industrial grade carbon steel and have a nickel-plated coating to resist corrosion..
  • LARGE CLEARANCE HOLE: These glass hole saw set along the drill bit facilitate the entrance of cooling water and escape of chips and other particles from drilling. Makes the drilling process easier..
  • APPLICATION: Suitable for drilling glass, ceramics, porcelain, ceramic tile, porcelain tile, limestone, marble, light stone and fiberglass..
  • WARM TIPS: Start drill at 45 Degree to surface and align to 91 Degree as hole forms.Water is required to cool down the drill when using them which will greatly extend the life of the bit..
Check Stock

4-1/2” Diamond Drill Bits Glass Hole Saw Drill Bit Set for Glass Ceramics Porcelain Ceramic Tile Marble

  • SMALL DRILL BIT: Hole diameter: 115mm(4-1/2"),total length: 56mm(2.2").Package includes 1 pcs 115mm diamond hole saw drill with a transparent box..
  • HIGH QUALITY: Diamond ceramic hole saw are made of industrial grade carbon steel and have a nickel-plated coating to resist corrosion..
  • LARGE CLEARANCE HOLE: These glass hole saw set along the drill bit facilitate the entrance of cooling water and escape of chips and other particles from drilling. Makes the drilling process easier..
  • APPLICATION: Suitable for drilling glass, ceramics, porcelain, ceramic tile, porcelain tile, limestone, marble, light stone and fiberglass..
  • WARM TIPS: Start drill at 45 Degree to surface and align to 91 Degree as hole forms.Water is required to cool down the drill when using them which will greatly extend the life of the bit..
Check Stock

VIKITON 4 inch Hole Saw with Arbor for Metal Wood Plastic, 102mm Bi-Metal Hole Cutter for Different Project with Smooth and Flat Drilling Edge, Fast Chip Removal

  • 【Sharp and Durable】The hole saw is Bi-metal construction, which has special flexible steel saw body and high speed steel cutting teeth, with longer service life, and more sharp..
  • 【Wide Application】The hole saw can be widely used for cutting thin metals, wood, plater board, plywood, duct, drywall, soft plaster, corn hole boards and plastic, good enough for the average DIYer and professional project..
  • 【Easy to Use】Pass the pilot drill bit of arbor through the center circular hole on the back of the hole saw, and rotate the arbor until it is tightened..
  • 【High Work Efficiency】The deep gullets on the sides of hole saw provides fast chip removal.
  • 【Tool Kit Includes】4 in hole saw, 1 drill bit for replacement, 1 arbor(with 1 drill bit), 1 hex key.
Check Stock

10 PCS 2 inch Desk Wire Cord Cable Grommets Hole Cover with Hole Saw Kit High Speed Bi-Metal Holesaw Drill Bits for Office PC Desk Cable Cord Organizer

  • Hole Saw Set: Package includes 10 pcs Desk Wire Cord Cable Grommets, 1pcs 2 inch M42 Bi-Metal hole saw, 1pcs 7/16 inch hex drilling shaft, 3pcs drill bit, and 1pcs M4 Hex wrench..
  • Hole Saw Drill Bit: The hole saw drill bit is made of M42 high-speed steel saw blade for better performance in durability and toughness, the cutter head is pointed and can open holes efficiently..
  • Desk Cable Grommets: Made of quality plastic, good comprehensive performance, wear-resistant, corrosion-resistant, durable to use. Removable cover, with an opening hole sleeve, which can open the hole and clip-on top cover, so if you have a lot of cords, you can use the desk grommet without cover..
  • Easy to Install: Just assemble the hole saw with the included hex wrench and drill the hole where needed, punching a hole first, then place the main part of the grommet directly into the hole, the overall size of grommets measures 2.5 x 0.77 inch (Dia. x H), fitted with the mounting hole diameter is 50 mm/ 2 inch..
  • Wide Application: Desk cord grommet can effective cable and wire management, neatly organize the wires from computer desks, PC peripheral, office equipment, entertainment systems in home, office and school..
Check Stock

COMOWARE Drill Bit Set, 246 Pcs Drill Bits, Drill Bit Sets for Cordless Drill, Drill Driver Bit Set for Wood, Metal, Masonry, Cement and Screwdriver Bits Set Combo Kit

  • 【ALL-IN-ONE CONVENIENCE】- COMOWARE 246 pcs drill bit set includes a wide variety of bits for wood, metal, masonry drilling and screw driving. It is a must-have drill driver bit set in your home garage. Ideal for DIY project and home repair..
  • 【CAPABILITY & DURABILITY】- Drill bits and screwdriver bits are made from superior HSS material for improved strength and durability. And the titanium finish and black oxide coating help the bits deliver higher drilling performance on wood and metal. Whether you are a mechanic or a DIY enthusiast, this drill bits combo kit will assist you in every application..
  • 【WELL ORGANIZED CASE】- The 246 pcs drill bits sets come with a portable storage case with uncluttered layout. There is a sponge cushion inside to help prevent the drill bits from falling off or mixed use. And the blue labels with drill bit sizes on are designed for easy identification of the bit size..
  • 【COMPLETE DRILL ACCESSORIES KIT】- Screwdriver bit set: 66 x 1" screwdriver bits, 30 x 2" screwdriver bits, 6 x nut drivers and 2 x hex keys. Twist drill bit set: 57 x HSS titanium drill bits, 30 x HSS b....
Check Stock

Koopi 2 Inch BI-Metal Hole Saw with Arbor and Replacement Pilot Drill Bit, 51mm Dia Hole Cutter for Easily Drilling Wood, Plastic, Thin Metal

  • This 2" Hole Saw Drill Bit is designed for wood / plastic cutting..
  • Arbor shank diamater- 3/8 in (fit for all 1/2"&3/8" drill).
  • Non-binding clean edge design make the hole saw blade cuts smooth and fast.More than that,the spring on the drill bit is nice because it automatically pushes the disc out of the saw immediately after completing the hole..
  • It is made of M42 BI-Metal and High Speed steel, Durable and cuts clear.
Check Stock

Greenworks 90 Piece Impact Rated Driving Set

  • SET INCLUDES: (21) 135° Split Point Black Oxide Drill Bits，(4) hex shank spade bits，(8) Hex Shank Nut Setters，(1)Magnetic Bit Holder, (27) 1 in. Insert Bits，(4) Drill Stops, (1) Countersink, (1) Center Punch, (1)Hex Key, (6) 2 in. Power Bits, (5) Carbide-tipped Masonry Drill Bits, (5) Black and Silver Brad Point Drill Bits, (4) Hole Saws, (1) Hole Saw Mandrel, (1) Carrying Case..
  • VERSATILE: Suitable for drilling wood, metal, plastic, and masonry..
  • CONVENIENT STORAGE: The plastic carrying case comes with a locking system and labeled compartments to keep your bits organized..
  • MAGNETIC BIT HOLDER: Magnetic bit holder holds drill bits for driving fasteners..
  • BLACK OXIDE FINISH: Provide superior durability and up to 50% improved lifetime compared to standard high-speed steel drill bits. They also reduce friction, giving you improved hole boring speeds..
Check Stock

MIKMAYTOO 1 Inch Carbide Hole Cutter, 25.4mm Hole Saw Metal, 1 inch Drill Hole Cutter for Thick Metal, Stainless Steel, Iron Pipes and Hard Material, Shank 3/8 inch Depth 1 inch

  • 【 Extremely Long Life 】25.4mm tungsten carbide hole saw is Industrial grade hole cutter, extremely durability for any tough material with over 10x times longer life than bi-metal and HSS hole cutters..
  • 【 Fast & Precise Cuts 】1 hole saw metal drill bit is carbide technology and optimized tooth geometry make hole saws provide superior lifetime and fast cutting in the most demanding applications..
  • 【 Applications 】1 carbide metal hole saw bit for metal provide fast and precise cuts into 3/4-inch thickness material such as : stainless steel, mild steel, alloy steel, aluminum, FRP, and plastic..
  • 【 Perfect Cutting Surface 】1 inch metal drill bit can precisely cut very high quality and smooth holes due to the excellent control of the concentricity rate..
  • 【 Double the cutting depth than other products 】1 inch metal hole saw bit cutting depth : 1 inch(25mm) ,but the other cutting depth is only 1/2 inch, so MIKMAYTOO hole saw bit for metal almost meets all metal material hole cutting..
Check Stock