Categories

Best I2c Cable

SparkFun Digital Temperature Sensor - TMP102 (Qwiic)-Compatible with Arduino and other Single-board computers Easy-to-Use I2C sensor Plug-and-Play breakout board Runs from 1.4-3.6V input Use with 3.3V

  • Uses the I2C interface. I2C Address: 0x48 by default (Three additional addresses available, as well). 12-bit, 0.0625°C resolution. Typical temperature accuracy of ±0.5°C.
  • 3.3V sensor. Supports up to four TMP102 sensors on the I2C bus at a time. 2x Qwiic Connectors.
  • The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V..
  • I2C communication uses an open drain signaling, so there is no need to use level shifting..
  • The alert pin is an over temperature alert, which has an open-drain and is pulled up through a 10kΩ resistor. The alert can also be read over I2C.
Check Stock

DORHEA 2Pcs BME280 5V Temperature Humidity Atmospheric Barometric Pressure Sensor Module GY-BME280-5V IIC I2C Breakout Board

  • The BME280 sensor is a precision sensor, is soldered onto PCB, not only the pressure and the temperature, this sensor can measure humidity..
  • BME280 5V uses both I2C and SPI (supports 3-, 4-wire SPI) interface. Interface: I2C (up to 3.4MHz).
  • Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI. for simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI..
  • The BME280 stmospheric pressure sensor is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings..
  • The BME280 sensor is precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy..
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

2 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module Blue I2C OLED Screen Driver DC 3.3V - 5V

  • What you will get: you will get 2 OLED display modules with classic display colors, self illumination with no need of backlight.
  • Power-saving display: the I2C OLED display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications)....
  • More details: this I2C LCD display is compatible with Arduino, ESP8266, ESP32, STM32, etc., 3.35V power.
  • Operating temperature: -40 - 85 degree....
  • Good compatibility: this I2C OLED display module is compatible with Raspberry Pi 4B/ 3B+/ 3B/ 2B/ Zero, compatible with Arduino, also compatible with....
  • Product manual: as shown in the instructions.
Check Stock

DS3231 AT24C32 IIC RTC Module Clock Timer Memory Module Beats Replace DS1307 I2C RTC Board (Batteries not Included) + 20 PCS Male to Female Jumper Wire Cable

  • DS1307 I2C real-time clock chip (RTC) 24C32 32K I2C EEPROM memory..
  • The DS1307 is accessed via the I2C protocol..
  • Two wire I2C interface. Hour: minutes: seconds AM/PM. Day month, date - year，Accurate calendar up to year 2100..
  • 1Hz output pin.56 Bytes of non-volatile memory available to user..
  • Size: 2.8cm x 2.7cm. / 1.14inch x 1.02inch..
Check Stock

Clock Splitter, Electronic Component Stable for Home for Industry

  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
Check Stock

Electronic Component, High Clock Splitter Practical for Home for Industry

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

Clock Splitter, Convenient Good Performance Electronic Component for Home for Industry

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

5 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V(Blue Display Color)

  • What will you get: there are 5 pieces OLED display module with blue display color, self-illuminated and no need backlight.
  • Power-saving display: the I2c oled display performs better than the traditional LCD display and with lower consumption sicne the IIC (I2C communications) simplifies connections.
  • Please note that these I2C OLED display module comes without pin headers.
  • More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
  • Good compatibility: this i2c oled display module is compatitable with Raspberry Pi 4B/3B+/3B/2B/Zero, compatitable with Arduino, also compatitable for ESP8266, ESP32, STM32, etc..
  • Product manual: as shown in the instructions.
Check Stock

ACEIRMC 8pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino

  • The adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use..
  • TCA9548 TCA9548A 1-to-8 I2C 8 -way multi-channel Expansion Board IIC Module Development Board.
Check Stock

Clock Splitter, Good Performance High Practical Electronic Component for Industry for Home

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

JM Set of 3 pcs Transparent 3D Floating Frame Display Holder/Box/Frames for Challenge Coins, AA Medallions, Antique, Jewelry,Gift, White, 2.75 x 2.75 x 0.75 Inches

  • What will you get: there are 5 pieces OLED display module with classic display color, self-illuminated and no need backlight.
  • Power-saving display: the I2C oled display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications) simplifies connections.
  • Please note that these I2C OLED display module comes without pin headers.
  • More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
  • Good compatibility: this i2c oled display module is compatible with Raspberry Pi 4B/3B+/3B/2B/Zero, compatible with Arduino, also compatible with ESP8266, ESP32, STM32, etc..
  • Product manual: as shown in the instructions.
Check Stock

SunFounder 2004 20x4 LCD Module IIC I2C Interface Adapter Blue Backlight Compatible with MEGA2560 Arduino R3 Raspberry (2 Pack)

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each. (2 Pack).
  • Compatible with Arduino R3/Mega2560 board..
Check Stock