Categories

Best Juki Servo Driver

Yamata Industrial Sewing Machine FY-8700 Lockstitch Sewing Machine Ergonomic Chair +Motor + Table Stand + LED Lamp Commercial Grade Sewing Machine for Sewing All Types of Fabrics (DDL-8700)

  • ✅ASSEMBLY REQUIRED, please note machine comes unassembled, with sewing machine table and Electronic 550 watts Energy saver and Quite Running DC Servo Motor. ✅Included accessories in the machine Juki DDL head: : Bobbin Winder Thread Stand Machine Oil Instruction Manual Oil Pan Knee Lifter V Belt.
  • ✅Juki DDL serie Single Needle Lockstitch Industrial Sewing Machine dont have the walking foot mechanisms. ( NOT a walking foot).
Check Stock

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

  • Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
  • Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
  • 2.You should connect higher power supply for higher-power servo.
  • 3.Make sure servo are connected properly, otherwise they will not move..
  • Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
  • Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..
Check Stock

Juki DDL550 LockStitch Industrial Sewing Machine Table,servo Motor,lamp,Made in Japan DIY

  • Specifications SPEED: 200-3700 spm MAX STITCH LENGTH: 5mm MAX PRESSER FOOT LIFT: 10-13mm LUBRICATION TYPE: Automatic (oil bath type) NEEDLE TYPE:DBX1 #11~#14.
  • Siruba's newest lockstitch plain machine is a smooth, quiet, power efficient industrial straight stitch Plainsewer 003e DIRECT-DRIVE NEEDLE POSITIONING LOCKSTITCH MACHINE. 003e MECHATRONIC INTEGRATION WITH BUILT-IN CONTROL BOX AND CONTROL PANEL. IT IS EASY TO INSTALL AND OPERATE. 003e DIRECT-DRIVE SERVO MOTOR (110Volts) IS SPEEDY, ACCURATE, AND ENERGY-SAVING THAN CLUTCH MOTOR BY 60%. 003e USER FRIENDLY: EQUIPPED WITH LED LIGHT, BUILT-IN BOBBIN WINDER, AND HALF STITCH FUNCTION..
  • Product Type Direct-Drive Needle Positioning Lockstitch Machine WHAT'S IN THE BOX : SIRUBA DL720-M1 machine head + TABLE STAND PLEASE NOTE! WILL BE DELIVERED UNASSEMBLED, will be delivered in 2 boxes, no detailed instructions for assembly. Highly Recommended to have a sewing technician to set up the machine..
  • The Presser Feet are compatible with VIRTUALLY ALL High-Shank, Single-Needle Industrial Sewing Machines, including:JUKI Style INDUSTRIAL Single Needle (DDL-8300 8500 8700 AND OTHERS) Sewing Machines ARTISAN BROTHER CONSEW COLUMBIA JUKI MITSUBISHI NAKAJIMA REX SINGER TAIKO..
Check Stock

Nema23 2N.m 57 Hybrid Closed Loop Servo Stepper Motor 2Nm 76mm+HSS57 Servo Driver Controller CNC Kit 24-50V DC For CNC Router Engraving Milling Machine

  • Name:Nema23 2N.M Servo Motor Driver CNC Kit.
  • Servo Driver:HSS57 2-Phase Hybrid Stepper Servo Driver.
  • The torque reducing is much lower than open loop stepper motor when it is at higher speed.The high speed performance and torque are enhanced in a....
Check Stock

Nema24 3N.m Closed Loop Stepper Servo Motor 88mm 5A+HSS60 Hybrid Driver CNC Kit for CNC Router Engrvaving Milling Machine

  • Servo Driver:HSS60 2-Phase Hybrid Stepper Servo Driver.
Check Stock

ALAMSCN 5PCS SG90 9g Servo Motor + 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit DIY Kit for RC Robot Arm Helicopter Airplane Car Boat Remote Control for Arduino for Raspberry pi

  • These SG90 9G micro servo motors have a completely new redesigned PCB and control system to provide more accuracy..
  • Its internal gearing and motor are also upgraded to improve dead bandwidth and centering..
  • For SG90 9G micro servo motor is far more accurate and safe to use in aircraft which require precise servo movements and perfect centering..
  • Apply to remote control helicopters, micro robot, robot arm and boats. Fit for ALL kind of R/C Toys and also make electronics DIY based on Arduino ,Raspberry Pi..
  • Package includes: 5PCS SG90 9g Micro Servo + 1PC PWM Servo Motor Driver. Cost-effective kit to meet your DIY needs..
Check Stock

Servo Driver HAT 16-Channel 12-bit I2C Interface PWM Outputs for Jetson Nano Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B Supports SG90 MG90S MG996R etc @XYGStudy

  • Servo Driver HAT for Raspberry Pi, 16-Channel, 12-bit, I2C Interface.
  • Needless to say, the Raspberry Pi is powerful enough in most cases, yet it's not that good at providing precise PWM output. You may have tried to....
  • Standard Raspberry Pi 40PIN GPIO extension header, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later version, Jetson Nano.
  • I2C controlled, using only 2 pins Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Check Stock

Tutto Machine On Wheels (Blush Pink Diamond, 20-Inch)

  • This Juki Cording Presser Foot for MO-1000 and MO-2000 sergers is an original Juki accessory..
  • Use the Juki Cording Presser Foot for MO-1000 and MO-2000 sergers to attach cording to your garments for a professional look..
  • The Juki Cording Presser Foot for MO-1000 and MO-2000 sergers is compatible with both the Juki MO-1000 and MO-2000 sergers..
Check Stock

Aoicrie 5pcs PCA9685 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit, for Robot or for Raspberry pi Shield Module servo Shield

  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)..
  • Communication Interface: IIC, PCA9685 contain an I2C-controlled PWM driver with a built-in clock..
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs..
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate..
  • 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or for Raspberry pi shield module servo shield..
Check Stock

Industrial Sewing Machine Juki DDL-8100 Lockstitch Servo Motor + Table Stand Cut Juki DDL8700 + LED Lamp+ Commercial Grade Sewing Machine

  • ✅ASSEMBLY REQUIRED, please note machine comes unassambled, with sewing machine table and Electronic 550 watts Energy saver and Quite Running DC Servo Motor..
  • ✅Included accessories in the machine 8100e head: : Bobbin Winder Thread Stand Machine Oil Instruction Manual Oil Pan Knee Lifter V Belt.
  • ✅Juki DDL-8100 Single Needle Lockstitch Industrial Sewing Machine ( NOT a walking foot).
  • ✅Up to 4500 stitches per minute Identical to and replaces DDL-8500 models Replaces popular DDL-MS and DDL-888 models, but has more speed Single-needle Lockstitch Maximum foot lift: 13 mm Maximum stitch length: 5 mm Maximum stitches: 6 stitches per inch. Needles: 9-18 DBX1 (16x231) up to size 19 Sewing Speed max.: 5,500 spm Stitch Length max.: 5 mm Presser Foot Lift by hand, max.: 5.5 mm.
  • by knee, max. 13 mm Needle Bar Stroke 30.7 mm Hook: auto-lubricating full rotary hook.
Check Stock

Juki Bobbin Case for TL Series Sewing Machines

  • Authentic Juki brand package of 5 plastic drop-in bobbins for all Juki household sewing machines except TL series..
  • Use with Juki Models: -HZL F600 -HZL F400 -HZL F300 -HZL G210 -HZL G110 -HZL K85 -HZL K65 -HZL 35Z -HZL 29Z -HZL 27Z.
Check Stock

Yamata FY335A 10\ Arm Cylinder Bed Walking Foot Sewing Machine with Servo Motor and Table.Assembly Required.DIY

  • ✅It come complete with sewing machine table, servo motor, everything (drawer, belt, tools, lamp and instruction manual) brand new, packed in sealed boxes and never been used before. Knockdown Table .DIY, professional assembly may required !.
  • ✅Included accessories in the machine 8100e head: : Bobbin Winder Thread Stand-Machine Oil- Instruction Manual -Oil Pan- Knee Lifter.
  • ✅Juki DDL-8100e Single Needle Lockstitch Industrial Sewing Machine ( NOT a walking foot).
  • ✅Up to 4500 stitches per minute Identical to and replaces DDL-8500 models Replaces popular DDL-MS and DDL-888 models, but has more speed Single-needle Lockstitch Maximum foot lift: 13 mm Maximum stitch length: 5 mm Maximum stitches: 6 stitches per inch. Needles: 9-18 DBX1 (16x231) up to size 19 Sewing Speed max.: 5,500 spm Stitch Length max.: 5 mm Presser Foot Lift by hand, max.: 5.5 mm.
  • by knee, max. 13 mm Needle Bar Stroke 30.7 mm Hook: auto-lubricating full rotary hook Industrial Sewing Machi.
Check Stock

Juki Original - Industrial Single Needle Sewing Machine Bobbins 12 Pack (Original Juki Part) Made in Japan

  • Original Genuine Juki Parts (Made In Japan).
  • Juki Bobbins Come in Sealed Juki Bags with Bar Codes / Do Not Accept unsealed Bags.
Check Stock