Categories

Best Light Aggregate Concrete Block

MRO Chem Perfect Patch 100 Percent Concrete Epoxy Patching Repair System Kit Restores Cracked Pitted or Worn Concrete Surfaces 50 Pounds 5 Gallons

  • EPOXY PATCHING SYSTEM: Permanent epoxy patching system seals cracks and holes and smooths over pitted concrete surfaces.
  • SUPER STRONG: Restores and even exceeds the strength of the original concrete.
  • Withstands traffic and even loads of up to 10,000 pounds.
  • COVERAGE: 50-pound, 5-gallon pail covers up to 100 square feet with a 1/8-inch thick coat.
  • APPLICATION: Three-part mixture includes epoxy, hardener, and aggregate.
  • Apply with a trowel, hand tamp, or roller for even coating.
  • USES: For use on walkways, staircases, streets, walls, ramps, and any indoor or outdoor concrete surface.
Check Stock

Deck Grip Non-Slip Sealer (5 Gallon) Clear Barefoot-Friendly Anti-Slip Coating - Create Traction for Outdoor or Indoor Floors and Pool Decks

  • ...-icing salts & chlorine. 5-Gallon Pail (treats 1500-3000 feet). Coverage is dependent on surface porosity..
  • SUITABLE SURFACES: Deck Grip is ideal for use on sealed or unsealed concrete, natural & manufactured stone, stained or unstained concrete, stamped or exposed aggregate concrete, brick, slate, sealed or unsealed tile & flagstone. Use Deck Grip on garage floors, driveways & sidewalks, pool decks & patios, entryways, as well as, warehouse & retail floors. Not for use on wood or composite wood surfaces..
  • LONG LASTING: If applied & maintained correctly, your floor will remain slip resistant for 2 years or longer. To maintain the surface after coating it with Deck Grip, routinely sweep and rinse using light pressure. To remove oily deposits or other foreign matters, use a pH-neutral cleaner and scrub lightly with a soft bristle deck brush..
  • SIMPLE & EFFECTIVE: Deck Grip is almost odorless & requires only moderate surface prep prior to treatment. Read & follow instructions carefully. Clean & dry the surface & apply Deck Grip with a 3/8” nap roller (included). Two thin coats a....
Check Stock

U. S. Chemical & Plastics Feather-Rite Lightweight Autobody Filler, Gallon (USC-21330) (4)

  • Pre-measured adhesive of polyester resin base, quartz sand and benzoyl peroxide hardener.
  • Sand and aggregate mixture is closest to natural concrete.
Check Stock

SUPERCOAT Stone Gray Epoxy Floor Coating

  • Breathable two-part waterborne epoxy coating, Decorative flakes, Anti-slip aggregate, Cleaner/Degreaser included.
  • Professional grade floor covering, Easy to install, No acid etching or mechanical prep necessary in most cases, Clean with degreaser included, mix and apply with roller, Scatter flakes in wet epoxy.
  • Epoxy coating breathes allowing moisture vapors to pass through eliminating blistering and peeling, Resistant to automotive fluids, hot tire lift, Good adhesion to concrete and wood.
Check Stock

Starrett KD0300-N 3-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

Starrett KD0400-N 4-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

Starrett KD0600-N 6-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

Zep HDSWEEP50 Floor Sweeping Compound, 50 lb

  • BEAUTIFUL WET LOOK SEALER Works on exposed aggregate, stamped, colored or decorative surfaces.
  • WILL NOT SIGNIFICANTLY DARKEN MOST SURFACEs when it dries. Does not look like you sprayed water on it. Resists chemicals and oil, Durable, Clear & Non-Yellowing..
  • PLEASE READ COMPLETE PRODUCT DESCRIPTION: Not for polished GRANITE OR MARBLE.
  • SPRAY, BRUSH OR ROLL on concrete, pavers, slate, driveways, garage floors, patios, masonry, brick warehouse floors.
  • MADE IN THE USA. Professional Results VERY low odor dries in hours..
Check Stock

Deck Grip Non-Slip Concrete and Tile Coating – Clear Barefoot-Friendly Anti-Slip Sealer - Slip Resistant Coating for Outdoor or Indoor Floors and Pool Decks

  • ...lon (treats 300-600 feet) or 5-Gallon Pail (treats 1500-3000 feet). Coverage is dependent on surface porosity..
  • SUITABLE SURFACES: Deck Grip is ideal for use on sealed or unsealed concrete, natural & manufactured stone, stained or unstained concrete, stamped or exposed aggregate concrete, brick, slate, sealed or unsealed tile & flagstone. Use Deck Grip on garage floors, driveways & sidewalks, pool decks & patios, entryways, as well as, warehouse & retail floors. Not for use on wood or composite wood surfaces..
  • LONG LASTING: If applied & maintained correctly, your floor will remain slip resistant for 2 years or longer. To maintain the surface after coating it with Deck Grip, routinely sweep and rinse using light pressure. To remove oily deposits or other foreign matters, use a pH-neutral cleaner and scrub lightly with a soft bristle deck brush..
  • SIMPLE & EFFECTIVE: Deck Grip is almost odorless & requires only moderate surface prep prior to treatment. Read & follow instructions carefully. Clean & dry the surface & apply Deck Grip with a 3/8” nap roller (included). Two thin coats a....
Check Stock

Starrett KD0414-N 4.1/4-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock

TEACH Flat Head Phillips Drive Concrete Screw to Anchor Masonry, Block & Brick,270-Piece

  • Concrete Screw Flange 5/8" Head (depending on the length, it will be either full or partial threaded). The diamond tip allows for superior penetriating into hard materials. Great for anchoring items to concrete, brick, block, or other masonry materials. Ceramic coating exceeds 500/hrs salt spray resistance.
  • An externally threaded, hardened screw with a double lead, consisting of alternating raised and lowered threads with notches cut into the raised threads, and a diamond-shaped, nail-type point. Cuts its own threads and when used in concrete, block or brick. Eliminates the need for an anchor when used in light or medium-duty applications. When used in concrete, it can be removed and re-driven into the same hole. Special carbide bits are recommended for driving concrete screws into masonry..
  • Some applications include anchoring the following to masonry: electrical junction boxes, wooden beams, plywood, exterior insulation, metal flashing, thresholds. Hole should be of a depth equal to the required embedment plus 1/2”.
  • Concrete screws should be installed a minimum of ten anchor diameters between each other. They have an advantage over most other types of masonry anchors in that they can be installed close to the edge of t....
Check Stock

QEP 6 in. x 2 in. Comfort Grip Flat Margin Flooring Trowel with Bucket Hook, Silver (42112)

  • Sandblasting finish for antirust, strong and durable. Carbon steel anti-rust performance is slightly lower than stainless steel, PLEASE keep the trowel dry after use.
  • [Flat Blades & Square End Type] Flat blade makes applications easier with more consistent finish. Beveled working blade edges prevent aggregate popping, can be used for application, smoothing, polishing and shining.
  • [Ergonomics Handle] No-turn handle design, ergonomic, camel-back wood handle makes them comfortable to use for less hand fatigue. Strong aluminum mounting securely welding with blades for long lifespan.
  • [Size Include] 3 Pieces concrete finishing trowels set includes 14’’ x 4’’, 12’’ x 4’’ & 8’’ x 3’’ different sizes, meet your different using requirement, will make your lives on the installation job easier, more efficient and more profitable.
  • [Professional Grade] The Goldblatt Concrete Finishing Trowels are an excellent choice for concrete hand work. Classically styled with a traditional camel-back wood handle, this trowel has been the industry standard for decades, will last for years to come.
Check Stock

Starrett - Sta-0329 KD0500-N 5-Inch Diamond Grit Holesaw

  • Effective cutting of hardened steels, fired ceramics, aggregate containing concrete, non-metallics and other difficult to cut materials.
  • Uniform synthetic diamond grit bonded over a durable steel platform.
  • Always use a coolant and start at a low speed, increase speed as ease of cutting is noticed while avoiding heat build-up on the cutting surface.
  • Recommended cutting speed is from 150 to 300-RPM.
Check Stock