Categories

Best Maximum Power Output

Sundown Audio SFB-5000D Monoblock AMP 5000W RMS Subwoofers Bass Amplifier

  • Maximum Output Power at 14.4V DC 1-Ohm: 5100W RMS.
  • Maximum Output Power at 14.4V DC 2-Ohm: ?W RMS.
  • Maximum Output Power at 14.4V DC 4-Ohm: ?W RMS.
Check Stock

Sundown Audio SAE-2000D V.3 Monoblock 2000W RMS Digital Class D Amplifier SAEv3-2000D

  • Features: Monoblock Class D Amplifier. Power Handling: Maximum Output Power at 14.4V DC 1-Ohm: 3000W RMS | Maximum Output Power at 14.4V DC 2-Ohm: 2025W RMS | Maximum Output Power at 14.4V DC 4-Ohm: 1140W RMS. Input Sensitivity: 200MV, Signal-to-Noise Ratio: 86dB, Frequency Response: 10Hz-20kHz (-3dB)..
  • Crossover: High Pass Filter: 15 to 80Hz (-12dB/8) Variable | Low Pass Filter: 80Hz to Full (-12dB/8) Variable. Bass Boost: 0 to 12dB (50Hz), Thermal Management: Smart Cooler (Fan Powered by Temperature or Audio with 3 Speeds), Input Impedance: 56K-Ohms, Protection System: Output Short/High/Low Supply Voltage/Thermal Protection, Minimum Supply Voltage: 9V DC, Maximum Supply Voltage: 16V DC, Dimensions: TBA..
Check Stock

YHJIC V8.5C EXP GDC Laptop External Independent Video Card Dock NGFF Notebook PCI-E Expansion Device

  • If you use N series card which over GTS450, and your laptop own Core ,and use the EGPU software to set,then it can use the laptop internal....
  • power supply interface:Support 12 volt power supply input interface type outer diameter 5.5MM, inner diameter 2.1MM, maximum power 150W, support the....
  • 6P power output:The maximum provides the interface output 6PIN+8PIN, maximum support 12A, maximum support 18A output with the motherboard and the. If....
  • 8P power supply interface:The main board and the equipment of the power supply interface, support soft switch function (notebook starting power....
  • （screen: use its notebook display need laptop comes with (R) HD and connected above GTS450 as .Otherwise you need external monitor.）The main....
Check Stock

OONO ATX 24/20-Pin DC Power Supply Breakout Module with 2.1A USB Port

  • 24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header..
  • Stand-By and Power-ON indicator LEDs. With latching button switch to control power output ON/OFF, it also supports external latching switch control power output ON/OFF(when using an external switch, the switch state on the module must be set to OFF).
  • With USB 5V power output, can support 2.1Amp output current for Apple products..
  • High quality screw terminal block for power output. +3.3V +5V +12V can support current maximum 24 Amp(continuous output 12 Amp), -12V can support current maximum 1 Amp..
  • ABS plastic enclosure, you can use screw mount to wood board or wall, of course, can also be placed on the desktop..
Check Stock

10 Pieces DC-DC Boost Converter 2A Adjustable Module Voltage Regulator Board Input Voltage 2 Volt-24 Volt to 5 Volt-28 Volt Output Voltage (Without USB Connector)

  • Product size: 36 x 17 x 14 mm/ 1.42 x 0.67 x 0.55 inch (L x W x H).
  • Method of use: the module of the IN+ and - after 2-24V, IN adjusting the potentiometer can adjust output voltage, output voltage is greater than the input voltage.
  • Matters needing attention: 1. The input voltage should not exceed the maximum input voltage.
  • 2. The peak current output current is no more than TV university.
  • Package included: 10 x DC-DC power apply module booster power module, max output is 28Volt.
Check Stock

SFB-1000D - Sundown Audio Monoblock 1750w RMS Amplifier…

  • Features: Monoblock Class D Amplifier. Power Handling: Maximum Output Power at 14.4V DC 1-Ohm: 3000W RMS | Maximum Output Power at 14.4V DC 2-Ohm:....
  • Crossover: High Pass Filter: 15 to 80Hz (-12dB/8) Variable | Low Pass Filter: 80Hz to Full (-12dB/8) Variable. Bass Boost: 0 to 12dB (50Hz), Thermal....
Check Stock

Accessory USA AC/DC Adapter for Leapfrog LEAPSTER 2 LEAPPAD Explorer Wall Charger Power Supply

  • Wide Compatibility: AC Adapter fit for LeapPad Glo, LeapPad2 Power, LeapPad2 Custom, LeapPad2, Leapster, LeapPad1, Leapster Explorer, LeapsterGS, Leapster2, Leapster L-max, Leapster-Tv..
  • Lput voltage: 100-240 VAC, 50/60 Hz , Output : 9V 1.5A, Maximum power: 13.5W, Power Cord length: 300cm ( 6.6ft ), DC plug size: 5.5x2.1mm（Center positive).
  • Power charger output current: 9v 0-1.5a (Will adjust the output current according to different devices (maximum 1.5A), so it is a perfect substitute for all 9Volt 100mA / -1500mA power supplies).
  • Durable：Made of the finest materials, the life of the power supply is longer than other products, More energy-saving and power-saving, saving of electricity bill than ordinary equipment. making it a durable and affordable product..
  • You will get: 1 power adapter, if the product is not satisfied 30 days refund service and 12 months warranty.
Check Stock

MakerFocus Raspberry Pi 4 Battery Pack UPS, RPI Pack Standard 4000mAh Raspberry Pi Battery USB Pack Raspberry Pi Latest Version V3Plus Expansion Board Power Supply Type-C for RPI 4B 3B+ 3B 2B+

  • ...ower than 2.5A. Recommended Use: 3V 2.5A power supply. ★Document link and Assemble video: Please get the link from the product description below.
  • Two power modes: Outdoor portable model and Indoor UPS power Supply mode: 1) As an outdoor portable power supply, the motherboard is powered by a lithium battery. and he maximum external power supply capacity is: 5.1V. 2.5A. 2)As an indoor UPS power supply mode: MicroUSB plugs into a normal 5V 2A power adapter, and the external output interface(USB-A interface) can output a maximum of 5.1V.3A. Battery size: 70mm x 41mm x 9.5mm.
  • 4+2LED are designed to show the status of battery power, charge or discharge:1) 4 Battery power LEDs: Used to show the current battery voltage and power. 2)The function of the Power LED is to display whether the UPS is supplying power to the Pi, and the LED is on: it means the output is 5V. LED off: Indicates that there is no voltage at the output. 3) Charge charging indicator LED: When the UPS is externally charged via the TYPE-C USB interface, the Charge LED starts to work..
  • The UPS has overcharge and overcurrent protection functions: When the UPS externally outputs about 4A, the UPS will consider the external circuit to be in a short-circuit state and automatically cut off the outp....
Check Stock

Generic Compatible Replacement AC Adapter Charger for LEAPSTER 2 LMAX L MAX DIDJ Charger Power Cord Mains PSU

  • Wide Compatibility: AC Adapter fit for LeapPad Glo, LeapPad2 Power, LeapPad2 Custom, LeapPad2, Leapster, LeapPad1, Leapster Explorer, LeapsterGS, Leapster2, Leapster L-max, Leapster-Tv..
  • Lput voltage: 100-240 VAC, 50/60 Hz , Output : 9V 1.5A, Maximum power: 13.5W, Power Cord length: 300cm ( 6.6ft ), DC plug size: 5.5x2.1mm（Center positive).
  • Power charger output current: 9v 0-1.5a (Will adjust the output current according to different devices (maximum 1.5A), so it is a perfect substitute for all 9Volt 100mA / -1500mA power supplies).
  • Durable：Made of the finest materials, the life of the power supply is longer than other products, More energy-saving and power-saving, saving of electricity bill than ordinary equipment. making it a durable and affordable product..
  • You will get: 1 power adapter, if the product is not satisfied 30 days refund service and 12 months warranty.
Check Stock

WOWOONE 30 Types 74HCxx Series Logic IC Assortment Kit, Logic Gates, Integrated Circuits Assortment Kit, TTL, High-Speed Si-Gate CMOS IC, Low-Power

  • Input point X element x0-x7, DC24 input, low level valid. X0-5 is the high-speed counting input port (default: 12K,100KHZ optional)..
  • Output analog voltage WR3A instruction, corresponding to the value 0-4095. Intermediate relay M: M0-M3071, the power loss preservation range can be set..
  • The maximum speed current is 1A. External load common terminating + 24, the other end received the PLC output port Y..
  • Y0-Y5 is optional relay or transistor output, relay output current 5A. The transistor output DC24V, the current maximum 1A..
  • 100Ms timer: t0-t199, accumulative power off save t184-t199.
  • 10Ms timer: T200-T249, accumulative power off saving T246-T249.
  • 1Ms timer: T250-T383, where T250-255 is cumulative.
  • 16-bit counter: C0-C199, power off to save C100-199.
  • 32-bit counter: C200-C219, power off to save C220-C234.
Check Stock

Reisong - BOYUURANGE A20 Hi-Fi Intergrated Amplifier KT88 Tube Single-end Class A 4ND VU Meter

  • The new power amplifier 0.35 cores do to ensure stable power supply..
  • Output power, maximum output power of 8W+8W..
  • Output amplifier uses no big loop feedback technology to ensure high sound reduction, powerful.
Check Stock

MakerFocus Raspberry Pi 4 Battery Pack UPS, RPI Pack Standard 10000mAh Raspberry Pi Battery USB Pack Raspberry Pi Latest Version V3Plus Expansion Board Power Supply Type-C for RPI 4B 3B+ 3B 2B+

  • ...V 2.5A power supply★ The document link is obtained in the product description.
  • The link to the assembly video is available on the product page, Two power supply modes: outdoor portable type and indoor UPS power supply mode: 1) As an outdoor portable power supply, the main board is powered by a lithium battery. The maximum external power supply capacity is: 5.1V. 2.5A. 2) As an indoor UPS power supply mode: the UPS power supply interface is connected to an external 5V power supply, the power supply requires 5V 2A-3A, and the maximum output current can reach 5V 3A..
  • 4+2LED are designed to show the status of battery power, charge or discharge:1) 4 Battery power LEDs: Used to show the current battery voltage and power. 2)The function of the Power LED is to display whether the UPS is supplying power to the Pi, and the LED is on: it means the output is 5V. LED off: Indicates that there is no voltage at the output. 3) Charge charging indicator LED: When the UPS is externally charged via the TYPE-C USB interface, the Charge LED starts to work.
  • The UPS has overcharge and overcurrent protection functions: When the UPS externally outputs about 4A, the UPS will consider the external circuit to be in a short-circuit state and automatically cut off the output. The ....
Check Stock

Alpine PDX-V9, 5-Channel Extreme Power Density Digital Amplifier w/Alpine RUX-KNOB.2 Remote Bass Level Control

  • MD 12000.1 – 0.5 ohm amplifier is developed with the highest technology and performance for automotive sound systems, in white color, to make your system more sophisticated, It is mono, with a single channel with a maximum power of 12.000 Watts RMS..
  • It is a FULL RANGE amplifier, playing all frequencies in the right measure for you, Operation class Class D, Number of Channels 01, Maximum power @ 12.6 VDC – 0.5 OHM: 12,000W RMS @ 12.6 VDC – 1 OHM: 7,200W RMS.
  • Input Sensitivity 220mV, Signal to Noise Ratio >95dB, Frequency Response 10 Hz ~5 kHz (-3dB), Crossover high pass (HPF) 10 Hz ~90 Hz (-12dB/8th) Variable, Crossover low pass (LPF) 90 Hz ~5 kHz (-12dB/8th) Variable, Bass Boost Freq.: 35 Hz ~55 Hz.
  • Boost: 0 ~10dB, Efficiency 79%, Input Impedance 15K ohms, Output Impedance 0,5 ohm, Protection system Output Short circuit, Output Short circuit in relation to the GND, Low Impedance Protection / High or Low voltage Protection / Thermal protection.
  • Maximum Power Supply Voltage 16VDC, Consumption at rest 3.6A, Maximum music consumption 602.5A, Maximum consumption in sinusoidal signal 1,205A, Dimensions (H x W x D) 8.976 x 2.755 x 21.653 inches (228 x 70 x 550mm), Weight 17.526 lbs (7.95 kg).
Check Stock