Categories

Best Metal Roofing

#8 x 1/2\ Stainless Philips Pan Head Sheetmetal Screw (1/2\ to 2\ Lengths in Listing) 100 Sheet Metal Screws (#8 x 1/2 Inch)

  • Dimensions: 5/16" Hex Head and ~9/16" EPDM washer - Shaft is .242" (#14) - Length under head 1".
  • #14 Sheet Metal roofing screws are galvanized for corrosion resistance.
  • Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
  • For installing roofing on a house, porch, airplane hangar, shed, pole barn, shop, barn or lean-to.
  • Rough Estimation - regular roofing project should require 80 screws per 10 x 10 section of roofing.
Check Stock

Ames Maximum Stretch - 4.6 Gallon Waterproof Sealant Membrane - Perfect For Roofing, Repairs, Concrete, EPDM & Wood - Liquid Rubber Sealer - Up To 650% Elastic - Made in USA

  • Ames Maximum-Stretch is a white, elastomeric, acrylic, rubberized roof coating & sealant with 650% elongation to resist cracking & peeling. With 88% light reflectivity, the bright white finish reduces surface temperatures resulting in lowered cooling costs..
  • Ames Maximum-Stretch adheres to metal roofing, tar, rolled roofs and more. Use as a RV roof sealant, waterproof sealant, rubber roofing material and more. Designed for low-slope roof maintenance..
  • 650% elongation - does not flake, chip or peel - elastomeric and rubberized coating and sealant. Rubber roofing material is 88% light reflective resulting in lowered cooling costs. Brush, roll or spray on!.
  • Non-toxic, eco-friendly, low VOC & made in the USA.
  • 4.6 Gallon - Tintable White - Our waterproof roof sealant is packaged in 5 gallon Pail. Designed for low-slope roof maintenance on metal roofing, built-up roofing, rolled roofing and more..
Check Stock

#14 Metal Roofing Screws 250 Screws x 1-1/2 Galvanized Hex Head Sheet Metal Roof Screw Self Starting Metal to Wood Sheet Metal Screws with EPDM Washer for Corrugated Roofing

  • Dimensions: 5/16" Hex Head and ~9/16" EPDM washer - Shaft is .242" (#14) - Length under head 1-1/2".
  • Polyurethane coated screw head is painted to closely match many brands of metal roofing (color may vary).
  • #14 Sheet Metal roofing screws are galvanized for corrosion resistance.
  • Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
  • For installing roofing on a house, porch, airplane hangar, shed, pole barn, shop, barn or lean-to.
Check Stock

Metal Roofing Screws 250 12 x 2 ZINC/NO Paint Hex ReGrip Sheet Metal Roof Screw Sharp Point Metal to Wood siding Screws.

  • #12 Sheet Metal ROOFING SCREWS.  Sharp Point ReGrip Screws. 5/16" Hex Head, ~9/16" Washer.
  • 250 COUNT Metal-to-wood roofing screws are galvanized and zinc coated to prevent rusting.
  • Hex washer head, sharp point roof screw with EPDM washer seal, seals roofing panel to screws..
  • Corrugated roofing and corrugated siding screws for pole barns, storage shed, shops, etc..
  • Galvanized Screw is Non-Painted and gets it's Color from the Galvanizing Process and is natural gray.
Check Stock

Metal Roofing Screws: (250) 10 x 2\  Galvanized Hex Head Sheet Metal Roof Screw. Self Starting Metal to Wood siding Screws. EPDM Washer. No Paint

  • Dimensions: 1/4" Hex Head - 1/2" EPDM Washer - Shaft .19" - Width .5" - Measures 2" Under Head.
  • Metal Screws are painted to closely match many brands of metal roofing though color may vary.
  • Colored roof screws head are painted with a two part polyurethane for longer product life (Not Zinc.
  • Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
  • #10 Sheet Metal roofing screws are galvanized for corrosion resistance.
Check Stock

Metal Roofing Screws 250 10 x 1 Galvanized Hex Head Sheet Metal Roof Screw Self Starting Metal to Wood siding Screws EPDM Washer No Paint

  • Dimensions: 1/4" Hex Head - 1/2" EPDM Washer - Shaft .19" - Width .5" - Measures 1".
  • Metal Screws are painted to closely match many brands of metal roofing though color may vary.
  • Colored roof screws head are painted with a two part polyurethane for longer product life (Not Zinc).
  • Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
  • No Paint/Galvanized Zinc screws go well with many types of gray, galvanized and other colors of roofing sheet metal.
Check Stock

1 Pail, 4 Gallon Each of Roofing Latex Bonding Glue Adhesive. 100% Full Refund Guarantee Available

  • 1 - 4 gallon pail of ROOFING latex Bonding Adhesive, covers 350 sq. ft. Trowel application is the recommended application as per the instructions as a ONE surface WET LAMINATE. However, if you wish to use a paint roller, we recommend using a 9" fine nap paint approved roller. If you use the roller, and not a trowel, you need to put the adhesive on BOTH surfaces and let TACK dry for 5 minutes or so, like a 2 sided solvent contact adhesive, depending on weather and heat conditions..
  • Used to adhere construction roofing membrane to surface, Not recommended to be used in temperatures lower than 50*. Temperature needs to be above 50* for 24 hours for full cure..
  • Latex NON HAZ MAT Bonding Adhesive. Top Quality. 100% FULL REFUND GUARANTEE.
  • Bond EPDM, TPO, and PVC Roofing to Wood, OSB, Plywood, Metal and BUR Roofing.
  • Use as a SINGLE surface wet laminate adhesive to bond your roofing membrane to the substrate. This is a BONDING Adhesive to adhere or bond the EPDM or TPO to a substrate of wood, plywood, OSB or metal. This is NOT a seaming product that will seam EPDM to EPDM or TPO to TPO, you must use a SEAMING product like black seaming adhesive or vulcanizing seaming tape which we have available for that type of application..
Check Stock

Dripping In Chocolate

  • Built in easy to install 5 FT sections. 4" leg goes under the shingle with 1.5" hemmed edge on the fascia..
  • Matching 1.5" metal roofing screws, 1/4" hex bit driver, and gloves included with each order..
  • 75 degree angle fits most roof pitches with ease. Made from 26 Gauge metal roofing material with 40 year paint finish..
  • Custom sizes and shapes available. Shipping is free. All orders are shipped out same or next business day..
Check Stock

IVY Classic 11163 Roofing Knife with Blade 1/Card

  • ALL METAL CONSTRUCTION: heavy-duty metal construction. Plated for rust resistance..
  • VERSATILE: cuts roofing material and shingles. Knife swivels open for blade change after removal of wing nut..
  • ROOFERS BLADE INCLUDED: retractable bowtie shaped blade adjusts to exact position and depth of cut..
  • COMPATIBILITY: fits Ivy Classic 11176 roofers blade and other roofing blades.
  • BLADE SPECIFICATIONS: high-carbon steel bowtie shaped with 4 cutting edges, blade thickness: .024"..
Check Stock

Roof Protector Underlayment Roll - 42\ x 286'

  • Lightweight for easy handling and installation with 90 day UV exposure.
  • Superior tear resistance compared to roofing felt for increased durability.
  • Ideal for for sloped (003e= 2:12) commercial and residential roofs and roofing applications under asphalt shingles or metal cladding.
Check Stock

Uni-Solar PVL-136 Power Bond PVL 136 Watt 24 Volt 216" x 15.5" inches. Flexible Solar Panel. Easiest to Install Peel & Stick.

  • Easy to install adhered directly to metal roofing pans, no racking system is required, laminates and metal roofing can be installed in one step.
  • there are no penetrations to the roof deck It has flexible.
  • Powerbond, flexible solar panel. Peel & Stick..
  • Measures 216-inches in length by 15.5-inches width by 0.2-inches in height.
Check Stock

DEKTITE #2 (DFE102B) Square Black EPDM Flexible Pipe Flashing, Roof Jack, Pipe Boot Flashing Dektite (for OD Pipe Sizes 1/4\ - 3\)

  • Dektite Base Seals Against Uneven Metal Roofing with Ease. Pipe Flashing Will Not Break or Crack..
  • This Pipe Flashing Boot Made By Deks is Made of EPDM for Long Life Even at Extreme Temperatures.
  • Black Dektite Pipe Flashing is Rated for Continuous Service Temperature Ranges of -58˚F to +239˚ F.
  • EPDM Rubber Boot with Flexible Base (Aluminum Collar). Pipe Boot Fits 1/4" to 3" Pipe OD..
  • Metal Roofing Pipe Flashing Boot is Designed for on-site Adjustment with a base of 7" x 7".
Check Stock

National Nail 135055 250CT 1-Inch Plastic Cap Nail

  • Deformed ring shank for greater holding power electro galvanized to enhance corrosion resistance. Conforms to surfaces..
  • All hand driven caps are packaged as integral nail-cap units Cap nails round plastic burron cap ring shank lgth 1 inch count=250..
  • Flexible round head conforms to surface making it difficult for water to get under the cap. use to secure roofing felt, sheathing, building papers, etc..
  • Can be used for roofing felt, sheathing, polyethylene, roll roofing, re-roofing, chicken wire, wire lathe. Flexible plastic head..
  • Flexible round head conforms to surface making it difficult for water to get under the cap. Can be used for roofing felt, sheathing, polyethylene, roll roofing, re-roofing, chicken wire, wire lathe..
Check Stock