Categories

Best Metric Fittings

Tecmolog Brass Pipe Fittings Connector G 1/2 Female Thread (Metric BSP) to US 1/2 NPT Male Thread Pipe Fitting Converter Adapter, SBA037

  • BSP to NPT Adapter: Metric BSP 1/2" (G) female to NPT 1/2" male pipe fitting converter, easily change from standard EU metric to US inches.
  • Brass Pipe Fittings 1/2: This adapter is made of brass for resistance to corrosion, ductility at high temperatures, and low magnetic permeability.
  • Rubber Washers and Teflon Tape for a Perfect Seal: Come with an o-ring for the G1/2 side and the 1/2 " NPT side to produce a leak free connection.
  • Connect Hoses or Fittings of US plumbing: This is used to adapt the plumbing to NPT on bath or kitchen fixture, and European hose fittings.
  • Easy to Install: It has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench.
Check Stock

LockNLube Simple 90 Coupler

  • Rated to 10,000 PSI! Locks on, stays on. Does not leak once locked on..
  • Hands free - does not pop off under pressure. Easily release from fittings with the thumb lever, even at extreme pressure..
  • Fits all standard Grease Guns - 1/8 NPT fitting. Fits all SAE and Metric Zerk fittings. Simply replace your existing coupler..
  • Over 3.5" of reach. Great for shielded PTO shafts, axles, harvester heads, U Joints and other recessed grease fittings..
  • Includes rebuild kit. Easily replace seal and jaws without replacing the coupler..
Check Stock

Performance Tool W5215 Performance Tool SAE/MET Grease Fitting Assortment - 70 Piece

  • METRIC FITTINGS: 6 mm – 1 Straight (10 pcs).
  • CASE: Convenient re-sealable container for storage and transport.
  • Overall size: 23 7/8-inch x 25-inch x 31-inch.
Check Stock

LockNLube Grease Gun Coupler XL - Extra reach for recessed grease fittings

  • Rated to 10,000 PSI! Locks on, stays on. Does not leak once locked on..
  • Hands free - does not pop off under pressure. Easily release from fittings with the thumb lever, even at extreme pressure..
  • Fits all standard Grease Guns - 1/8 NPT fitting. Fits all SAE and Metric Zerk fittings. Simply replace your existing coupler..
  • Over 3.5" of reach. Great for shielded PTO shafts, axles, harvester heads, U Joints and other recessed grease fittings..
  • Includes rebuild kit. Easily replace seal and jaws without replacing the coupler..
Check Stock

POHIR Pressure Washer Adapter Set, 14-Pack Quick Connect Fittings, 3/8 Power Washer Quick Disconnect Kit with M22 Swivel to 3/8'' Quick Connect, 3/4\ to Quick Release and M22 15mm to 14mm Male

  • 14-Pack Quick Connect Kit - 4-pieces Metric M22-14 female to 3/8 quick plug, 2-pieces m22 14mm female to 3/8 quick disconnect, 2-pieces M22 14mm male to 3/8’’ quick disconnect, 2-pieces M22 14mm male thread to m22 14/15 male, 2-pieces 3/4 female to 1/2 quick connect, 2-pieces 1/2 plug to 3/4 male.
  • Easy Connect & Disconnect - M22 quick connect fittings help pressure washer hose quick connect to pressure washer pump or gun. The 3/4 quick coupler fits all 3/4" GHT (garden hose thread) watering equipment..
  • M22 Male to Male - 1x M22 15mm male to 14mm male and 1x M22 14mm to 14mm male adapter, convert the metric M22 14mm male thread to the M22 14mm or 15mm swirl as needed..
  • High-Quality Brass Quick Connect - Made of solid brass, stainless steel and engineering plastics, for a safe and leak free connection. These quick connect fittings are durable, rust proof, providing secure fittings and are convenient for frequent connection. .
  • Warm Tips: Inner diameter of M22 -14 swivel is 14MM NOT 15mm. Do NOT use the threaded 14MM to connect M22-15mm fittings, or it will cause leakage. Please lubricate the accessories before use..
Check Stock

AZUNO Hydraulic Grease Fittings 240 Pieces SAE & Metric Grease Fitting Assortment with 120 PCS Grease Fitting Caps Standard Grease Gun Fittings Perfect for Replacing Missing or Broken Zerk Fitting

  • 【240 Pieces Kit】 Total 240pcs includes 120pcs SAE and 120pcs METRIC. SAE packed with 6 kinds, 1/4” and 1/8” NPT in straight 45° and 90°.....
  • 【Build to Last】Constructed from high-strength zinc-plated steel for extra strength and rust-resistance..
  • 【Tested and Certified】Meet and exceeds ISO/TS16949 certified and industry benchmark 48 Hours corrosion resistance tested..
  • 【Grease Zerk Caps】120pcs rend and black grease fitting caps differenciated SAE and METRIC fittings. Protect grease fittings from corrosion and....
  • 【Keep Organized with Durable Case】 Thick polypropylene (PP) case with double snap locks to keep secure of grease zerk assortment..
Check Stock

Complete Grease Fitting Replacement Kit - SAE and metric Zerks multi-tools fitting caps

  • Includes most common SAE and metric grease fittings.
  • Two multi-tools allow easy removal and installation of all sizes of grease fitting, even if broken..
  • 20 plastic caps keep grease fittings clean and help them last longer.
  • Bright plastic case keep parts clean and easy to find, even on the job site, or the back of a dark truck.
Check Stock

Steel Power Steering Box Adapter Fitting 18mm-1.5 IFM/-6 AN, 80-Up GM

  • This adapter fitting is commonly used to adapt power steering boxes to AN 6 connections.
  • 18 mm-1.5 O-ring seal on one end and AN6 male on the other.
  • Inverted flare fittings are used on most GM power steering boxes 1977 and older.
  • Metric thread O-ring fittings are used on later model GM power steering boxes 1978 and newer.
Check Stock

Steel Power Steering Box Adapter Fitting 14mm-1.5 IFM/-6 AN, 80-Up GM

  • This adapter fitting is commonly used to adapt power steering boxes to AN 6 connections.
  • 14 mm-1.5 O-ring seal on one end and AN6 male on the other.
  • Inverted flare fittings are used on most GM power steering boxes 1977 and older.
  • Metric thread O-ring fittings are used on later model GM power steering boxes 1978 and newer.
Check Stock

(2 pcs) Drettyer Brass Pipe Adapter Plumbing, G Thread 1/2" Male to NPT Thread 1/2" Male Pipe Fitting Adapter 2 inch long, Seamless and Leakproof

  • ✅Size - G1/2" Male ,NPT 1/2 " Male,2 inch length..
  • ✅Material - High grade solid brass, strong and wear resistant, more durable than iron and iron galvanized pipe fittings.Brass is corrosion resistant and can be used in wet environments..
  • ✅Purpose - G1/2" Pipe fittings Male Thread Water Pipe to 1/2" NPT Adapter.It can be applied to most of the pipes or fittings adapters, or a variety of scene needs..
  • ✅Seamless Connection - Metric BSP 1/2" (G) male to NPT 1/2" male pipe fitting converter (Brass).The seamless close nipple brass fittings and the overall threaded design will make the installation seamless.This will be more beautiful..
  • ✅Tips - Drettyerr is committed to providing quality products. The deeper and smoother thread design will make the installation process easier and more efficient.(Please note, NPT Thread Size is a nominal pipe size and it does not represent the actual diameter.).
Check Stock

Frienda 12 Pieces 3/8 Inch-24 Threads Brake Line Fittings Assortment for 3/16 Inch Tube (4 Unions, 8 Nuts)

  • Fit for: the unions measures approx. 0.6 x 0.9 inch, the nut measures approx. 0.67 x 3/8 inch, fit for most common inverted flare or double flare sizes for 3/16 inch tube, for use with 3/16 inch steel, poly coated or copper brake lines.
  • Please confirm the size of the details according to the picture before purchasing.
  • Size and material: both the unions and nuts are metric 3/8-24 threads (regular 3/16 inch tube fitting size), all brake line fittings are made of quality brass to prevent rust and plated for corrosion resistance.
  • You will get: 12 pieces brake line fittings in the package, include 4 pieces unions and 8 pieces nuts, you can share them with your family and friends, these tubes unions are good fittings.
  • Inverted flare union: these unions are a nice option to join 2 (3/16 inch) brake lines together.
  • Brake line fitting connect: the nut is called the fitting for 3/16 inch tube, these unions fittings have a hex size of 3/8 inch and the threads are 3/8 inch with a thread pitch of 24.
Check Stock

Glarks 156Pcs Metric & SAE Straight and 45 Degree and 90 Degree Hydraulic Grease Brass Zerk Grease Nipple Fitting with 60Pcs M6 M10 Caps Assortment Kit

  • ☀ [What You Get]: This kit includes 12 sizes of Metric and SAE grease fittings, M6 x 1 straight for 10pcs, M6 x 1 90-degree for 7pcs, M6 x 1 45-degree for 7pcs, M10 x 1 90-degree for 10pcs, M10 x 1 45-degree for 7pcs. 1/8''-27 straight for 10pcs, 1/8''-27 45 degree for 7pcs, 1/8''-27 90 degree for 7pcs, 1/4''-28 straight for 10pcs, 1/4''-28 45 degree for 7pcs, 1/4''-28 90 degree for 7pcs. Red(M6) caps for 30pcs, black (M10) caps for 30pcs. Total 156pcs which are sorted packed in a plastic box..
  • ☀ [Premium Material]: Grease fittings are made of high-quality brass. Not only the surface is clean and shiny, but also anti-corrosion and anti-rust. They can work for a long time, use them to replace damage zerk fittings, and you will no longer have to worry fitting loss or damage..
  • ☀ [Strong Tightness]: The thread on the grease fittings is clean, tidy and deep, which can ensure that fitting is tightly engaged with grease lines, and prevent the fitting from fulling off or oil leaking form the side..
  • ☀ [Grease Fitting Cap]: Red (m6), black (m10) caps are included in the kit, different colors are convenient for you to distinguish. They can prevent dust, dirt and other pollutants from entering the nozzle, thereby extending the life of the grease fittin....
Check Stock

Beck Arnley 016-0088 Oil Drain Plug

  • OEM VERIFIED: All parts meet or exceed OEM standards.
  • STRONG, STURDY, RELIABLE: Parts made of high-strength, corrosion-resistant materials.
  • FOR FORD AUTOMOBILES: Parts engineered for use in Ford automotive fittings and applications.
  • M14-1.50 METRIC FINE THREAD: Fits an M14-1.50 fine threaded socket or hole.
Check Stock