Best Microcontroller compatible
Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board
- Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
- Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
- The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
- Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
- All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
- High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
- Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check StockKOOBOOK 2Sets HX1838 NEC Infrared IR Remote Control Sensor Module IR Receiver Module DIY Kit for arduino
- Operating voltage 5V.Output form: Digital output..
- VCC: 3.3V-5V external voltage (can be directly connected to the 5v microcontroller and 3.3v microcontroller).GND: external GND.IN: external microcontroller I/O port, I/O port has been designed 10K pull-up resistor..
- Kit theory test distance of about 5-8 meters, but the practical application depends on the ambient factors you use, as well as the middle barrier (such as diaphragm, glass, obstructions or other material blocking), receiving head with HX1838 with power work instructions lights, receive 38K frequency any remote coding data..
- remote Control Battery:CR2032 Button batteries (Not Included).
Check StockDorhea 4Pcs ESP8266 ESP-12F WiFi Serial Module Microcontroller 802.11N Development Board Wireless Transceiver Remote Port Network Module for NodeMCU MicroPython
- The ESP-12F module combines the ESP8266 microcontroller with 4MB of flash and a PCB antenna, with 16-bit Lite mode, clocked at Supports 80 MHz and 160 MHz, supports RTOS, and integrates Wi-Fi MAC/BB/RF/PA/LNA..
- The ESP-12F WiFi module supports the standard IEEE802.11 b/g/n protocol, a complete TCP/IP protocol stack. Users can use this module to add networking capabilities to existing devices or to build separate network controllers..
- The default firmware can add WIFI capability to another microcontroller, but it really shines when loaded with MicroPython, or NodeMCU..
- The ESP-12F is an improved version of the 12E, improve the peripheral circuit, the four laminates plate process, enhanced impedance matching, signal output is better, It is pin compatible with enhanced stability and a better antenna..
- Not recommended for users who are new to the ESP8266. New users should instead look at development boards with integrated USB..
Check StockEmporio Armani Mens ART3016 Analog Display Quartz Black Smart Watch
- Compatibility: android os 5.0+, iphone 5/ios 9.0+.
- connectivity: battery life: up to 1 year based on usage.
Check StockArduino Mega 2560 REV3 [A000067]
- Arduino Mega 2560 is designed for your most ambitious projects which require additional pins and extra memory.
- Based on the 8-bit AVR microcontroller ATmega2560, it has 54 digital I/O pins, 16 analog inputs and a larger space for your sketches.
- Compatible with most shields designed for the Arduino Uno.
- Arduino is an open-source hardware, software, and content platform with a worldwide community of over 30 million active users..
Check StockSparkFun RedBoard - Compatible with Arduino Breadboard-able Development board w/ R3 footprint Microcontroller serves as physical computing learning platform Connect to computer with USB Mini-B
- ATmega328 microcontroller with Optiboot (UNO) Bootloader. Compatible with Arduino IDE. R3 shield compatible..
- USB Programming Facilitated by the Ubiquitous FTDI FT232RL.
- Input voltage - 7-15V 0-5V outputs with 3.3V compatible inputs.
- You'll also need a mini-B-to-A USB cable It powers the RedBoard and allows you to upload programs to it.
Check StockDEVMO NEO-7M GPS Satellite Positioning Module with SMA Antenna Interface Compatible with Ard-uino STM32 C51 Replace NEO-6M
- ★Get 51 Ard-uino STM32 microcontroller routine..
- ★with a USB interface, you can watch the computer positioning effect directly phone line..
- ★with the passive ceramic antenna and passive antenna amplifier, make better use of the individual effects..
- ★with SMA interface can be directly connected to an active antenna SMA..
- ★TTL level, compatible with 3.3V/5V systems. TTL level, compatible with 3.3V/5V systems..
Check Stockkuman Compatible For Arduino Raspberry pi Sensor kit 37 in 1 Robot Projects Starter Kits with Tutorials Compatible for Arduino RPi 3 2 Model B B+ K5
- Professional 37-in-1 Sensor Module Kit, NOT ONLY compatible for ARDUINO, BUT ALSO compatible for raspberry pi RPi 3 2 Model B A A+ B+.
- Complete Update and common models for arduino Mega 2560 starter kit.
- Great sensor kit with tutorials compatible for Arduino and raspberry pi..
- Standard interface can be controlled directly by microcontroller ( 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Detailed tutorials including project introduction and source code CAN BE PROVIDED..
Check StockArduino Vidor 4000 [ABX00022]
- The best of the embedded world: a low power microcontroller to handle reprogramming, communication, and analog sensing, together with an FPGA to perform high speed computation, and a dual WiFi-BLE chipset for wireless communication..
- Mini HDMI output / MIPI camera input: can capture sound in real time, create a real-time computer reading sensor information,sending it to monitor or capture video, overlay sensor information on the image and send it to a screen..
- Ideal for: Industry 4.0, home automation, computer vision, aerospace, telecommunications.
- Part of the Arduino Maker Board Family for IoT Devices, easy to program with Arduino Software and Intel’s FPGA suite..
- Easy interface between the microcontroller and the FPGA at the software level..
Check StockSainSmart USB 4 Channel Relay Automation (5V)
- NOYITO 2-Channel Micro USB Relay Module is equipped with a stable USB to serial port chip and a microcontroller. It can use the serial port debugging software to send serial commands on the computer to control the opening and closing of the 2-channel relay..
- Onboard high performance microcontroller chip, CH340 USB control chip.With power LED indicator and relay status LED.On-board 2-channel 5V, 10A/250VAC, 10A/30VDC relay, long relay life, can work 100,000 times continuously..
- Module with overcurrent protection and relay diode freewheel protection..
- NOYITO 8-Channel Micro USB Relay Module ASIN:B09RGTSHHW.
- NOYITO 4-Channel Micro USB Relay Module ASIN:B09RGVQXXT.
Check StockELEGOO MEGA R3 Board ATmega 2560 + USB Cable Compatible with Arduino IDE Projects RoHS Compliant
- The Mega is 100% compatible with Arduino IDE and most of the shields are designed for the Arduino mega R3,RoHS Compliant.
- The chip is Atmega + 2560-16au and 16u2, same with the official version..
- Improved and expert version: 1. 0 pinout: added SDA and SCL pins that are near to the AREF pin.
- Stronger RESET circuit. Use 5. 5 * 2. 1mm DC barrel jack (compatible with 5. 5 * 2. 5mm DC barrel jack).
- It contains everything needed to support the microcontroller.
- simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started..
Check StockDorhea 37 in 1 Sensor Modules Kit with Tutorial for R3 Board Mega2560 Mega328 Nano Compatible with IDE Raspberry Pi
- 37 in 1 sensor module Kit is complete update and common models,compatible with arduino R3, MEGA 2560, NANO and Raspberry pi..
- All components compatible with Arduino IDE, can be used directly..
- Standard interface can be controlled directly by microcontroller ( 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)..
- Upgraded tutorial only for R3, MEGA2560 R3, NANO in CD, There are tutorials in the CD that comes with..
- Complete Update and common models for arduino NANO R3 Mega 2560 starter kit..
Check StockDiodes Incorporated Microprocessors - MPU ARM Cortex-A5 MPU 32bit, Video decoder (ATSAMA5D44A-CU)
- 1 Pcs ATTINY84A-PU 8-bit Microcontroller with 8K Bytes In-System Programmable Flash..
- MCU MICROCONTROLLER, 8 BIT, ATTINY, 20MHZ, DIP-14..
- 8K Bytes of In-System, Self-programmable Flash Program Memory.
- 512 Bytes of In-System Programmable EEPROM.
- New and original ,quality ensured , no-hassle refund if you are not 100% satisfied!.
Check Stock