Categories

Best Mmdvm Raspberry Pi 3

C4Labs DRPi-1NSX case for Raspberry Pi 3 B+, Duplex MMDVM v1.0, 2.4″ Enhanced Nextion Screen (Included) ~ (Black Ice)

  • Full body coverage for Raspberry Pi 3B (not included), Duplex MMDVM v1.0 dual antenna (not included), and 2.4" Nextion Touchscreen(included). Case kit requires assembly. Case is not waterproof..
  • Includes a 2.4″ Enhanced Nextion Touchscreen**Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • For Raspberry Pi 3B+, 3B, 2B, and B+ (not included), Duplex MMDVM v1.0 (not included), and a 2.4″ Enhanced Nextion Touchscreen (included).
  • Designed and Crafted by Local Artists at our workshop in Tacoma, WA USA.
Check Stock

C4Labs JRPi-3.5NSX Nextion Screen Case for Raspberry Pi 4B & 3B+, Jumbospot MMDVM, and 3.5\ Nextion Screen (Included)

  • If you have a Zumspot Brand MMDVM Board there is a new case model: ZRPI-3.5NSX.
  • For Raspberry Pi 4B, 3B+, 3B, 2B, and B+ (not included), JUMBOspot (a generic Chinese MMDVM board - Not included), and a 3.5″ Enhanced Nextion Touchscreen (included). Carefully designed to precisely fit these components using Laser cut components and stainless steel hardware. Full body coverage for components (not waterproof). Heat sinks and rubber feet included..
  • *Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • Note: This case does not have a fan and the Pi-4 is known to run hot under use. It is not recommended to run the Pi-4 at full power for extended periods as performance problems can arise at higher temperatures.* The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • Engineered and manufactured with Pride in Tacoma, WA USA.
Check Stock

C4Labs JRZ-1SB case Compatible with Raspberry Pi Zero/Zero W & JumboSPOT MMDVM & Waveshare UPS Hat (Black Ice)

  • Full body coverage for Raspberry Pi, Battery Hat, JumboSPOT or LoneStar N5BOC MMDVM Simplex and OLED screen (not waterproof) Note: Raspberry Pi Zero 2 has not been tested for heat issues..
  • Enough room for .96″ OLED screen to be mounted directly to JumboSPOT or LoneStar N5BOC MMDVM Simplex by customer.
  • Cut outs for easy access to SD card and camera ports.
  • Pin-hole access to boot and reset buttons on top of case.
  • No components are included. This is a Case Kit and assembly is required..
  • Designed and Crafted by local artists in Tacoma, WA USA.
  • Comes with 2 tops: one with antenna hole and one without.
  • Compatible with Lonestar N5BOC Board version 03/23/2019 1V8-1.
Check Stock

Hima MMDVM Hotspot Spot Radio Station+ Antenna + OLED with Screen Support P25 DMR YSF D-Star UHF Expansion Board WiFi Digital Voice Modem Suitable for Raspberry Pi-Zero W, Pi 3, Pi 3B+

  • The kit includes: high performance with screen ARM processor, SMA antenna connector, including antenna, 2 pins, 4 screws..
  • Support:D-STAR, P25, DMR and work with UHF.Software:Pi-Star,Suit for Raspberry Pi 3,Raspberry PI-Zero w, Raspberry Pi 3b+.The 40pin raspberry pie needs to insulate the middle 20pin pin headers for normal use..
  • Power supply: USB cable connected to your computer or laptop. The Hotspot will also work mobile in your vehicle if you Tether it to your mobile phone network..
  • Basic Setup: 433.550000MHZ DMR (Need the 2.4GHz SSID as the Pi W doesn't support 5.8GHz)..
  • Note: All designs will be contributed on MMDVM open source project.If you encounter a different version of pi zero not work, please see the picture instructions. If you have any difficult， please contact us to help you solve the problem..
Check Stock

C4Labs ZRPi-3.5NSX Nextion Screen Case – Raspberry Pi 3 B+, ZUMspot MMDVM, and Enhanced 3.5\ Nextion Screen (Included) ~ Black Ice

  • If you have a Generic Chinese MMDVM Board (Jumbospot) there is a new case model: JRPI-3.5NSX.
  • For Raspberry Pi 4B, 3B+, 3B, 2B, and B+ (not included), ZUMspot Brand MMDVM Board (Not included), and a 3.5" Enhanced Nextion Touchscreen (included). Carefully designed to precisely fit these components using Laser cut components and stainless steel hardware. Full body coverage for components (not waterproof). Heat sinks and rubber feet included..
  • *Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions..
  • Note: This case does not have a fan and the Pi-4 is known to run hot under use. It is not recommended to run the Pi-4 at full power for extended periods as performance problems can arise at higher temperatures.* The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included).
  • Engineered and manufactured with Pride in Tacoma, WA USA.
Check Stock

MMDVM Duplex Hotspot Module Dual Hat V1.3 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi with USB Port (Without OLED)

  • if the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat.
  • HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece..
  • WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion.
  • WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4..
  • Update new FW: (pi-star / expert / ssh access / user :pi-star pass:raspberry) then run sudo pistar-mmdvmhshatflash hs_dual_hat set Jumper BOOT0=1,BOOT1=0 and soler JP1 First! After upgraded finished, disconnect JP1.
  • FREQUENCY: Radio Frequency : Freq:144-148,219-225, (Main Band) 420-475,842-950 NOTE: TX =0, RX=0. Modem select: STM32-DVM/MMDVM_HS-Raspberry pi Hat(GPIO) or any other (GPIO board).
Check Stock

MMDVM Hotspot Board + Aluminium Case Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, Pi 3 (Raspberry Pi NOT Included)

  • Save electricity, High quality TCXO, stable, low BER. Note: This is NOT a completed or assembled Hotspot, it is just MMDVM Board with Aluminum case..
  • Support Raspberry Pi 3B, Pi ZERO, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model).
  • Support VHF/UHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions).
  • Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG.
  • Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules.
Check Stock

Zopsc Digital Trunk Board with Expansion Board for Raspberry Pi GS68 MMDVM DMR Repeater, Support for Upgrades via for ST-Link, USB, GPIO.

  • With USB interface, can connect for Raspberry Pi and PC, built-in PL2303 model..
  • Support MMDVM mode for DMR / YSF / P25 / NXDN / DSTAR / POCSAG..
  • The Repeater and Simplex modes can be changed at any time by changing the RX / TX board sequence..
  • Support for Raspberry Pi 3B/ 3B/ Pi ZERO, compatible with for NanoPi NEO, for Orange Pi, compatible with for BlueDV (requires USB to TTL or Bluetooth model)..
  • Support for VHF / UFH, frequency range, depending on your external radio..
Check Stock

MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Supports Digital Radio Only NXDN POCSAG P25 YSF DSTAR C4FM DMR

  • ✔➸ Added external inductor. Support VHF communication, the effect cannot reach the perfect effect of UHF.
  • ✔➸ MMDVM hotspot is a fully-assembled device..
  • ✔➸ HOTSPOT comes pre-configured for a Wi-Fi network. SSID: Pi-Star (or Pi-Star-Setup) Password: raspberry, Just connect to temporarily WIFI: pi-star then you can access the device through your web browser using Pi-Star. And then save your own house WIFI details to HOTSPOT according to the step 2 of the instruction manual..
  • ✔➸ HOTSPOT size: 2.8 x 1.3 x 0.9” inch.
Check Stock

MMDVM Duplex Hotspot Module Dual Hat with 0.96 OLED Display V1.47 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi (with OLED)

  • if the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat.
  • HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece..
  • WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion.
  • WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4..
  • EASY OPERATION: The firmware is pre-loaded and is easily upgraded via software. Onboard LEDs showing status (Tx,Rx,PTT,Mode).
  • FREQUENCY: UHF 433-900MHz, VHF 144-220 MHz. NOTE: TX =0, RX=0. Modem select: STM32_HS_GPIO.
  • To leave the screen on all the time In Pi-Star configuration, ensure you have "OLED Type 3" in the display type field at the top of the page, set Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to 1. This leaves the screen on all the time. Otherwise, it goes blank when idle.
Check Stock

Smraza Raspberry Pi 3 B+ Case with Fan, 5V 2.5A Power Supply and 3 Heat Sinks for Raspberry Pi 3 Model B+ (B Plus), 3B, 2B

  • ✓ The Latest Version 9 Layers case for Raspberry Pi 3 model B+ / Raspberry pi 3 /pi 3 model b / pi 2 / pi 2 b (Not include Pi Board).
  • ✓ Raspberry Pi Case has the layout design for the Raspberry pi 3 model b+ and will perfectly protect your pi components.
  • ✓ Easy to access all GPIO ports - Raspberry pi case with cutout to allow Pi's GPIO, HDMI, USB, SD, Power Supply and Other GPIO Ports access.
  • ✓ Made of Acrylic, the raspberry pi 3b case Won’t Block your raspberry pi's Wifi / Bluetooth Signal.
  • ✓5V 2.5A power supply with 59 Inch power cable is durable, on/off switch would cause less wear and tear on your raspberry pi's power port. Package Include: Raspberry Pi 3 B+ Case, Fan, 3 Pcs Heatsinks, 2.5A Power Supply.
Check Stock

LoveRPi Power-Over-Ethernet (PoE) HAT Kit for Raspberry Pi 3 Model B+ with Black Case

  • ULTIMATE POWER OVER ETHERNET HAT FOR RASPBERRY PI 3 B+: Deliver clean and reliable power to the latest Pi 3 Model B+ by removing the problematic MicroUSB plug altogether! Power-over-Ethernet is both simple, power efficient, and cost effective compared to having multiple power adapters..
  • BUILT FOR CLUSTER NODES: Simplify cable management and expand your on-premise cloud with POE! Power five, ten, twenty Raspberry Pi 3 Model B+ boards through a single POE switch. This PoE HAT was designed to exceed the power delivery standards set by the official Raspberry Pi PoE HAT and other products available on the market..
  • POWER OVER ETHERNET SWITCH REQUIRED: Network switch must be compliant with IEEE 802.3af PoE standard. PoE power output must be within the budget of the switch when powering multiple boards. PoE switch and Raspberry Pi 3 Model B+ sold separately..
  • ANODIZED HEATSINK AND VENTILATED CASE WITH COOLING FAN INCLUDED: Raspberry Pi 3 Model B+ gets very hot and active cooling is the only way to prevent temperatures from exceeding 150°F! This kit includes everything you need to keep your PoE powered board operating at maximum performance. Raspberry Pi 3 Model B+ sold separately!.
  • NOT COMPATIBLE WITH RASPBERRY PI 4 OR RASPBERRY PI 3 MODEL B AND OLDER MODE....
Check Stock

Seeed Studio ReSpeaker 4-Mic Array for Raspberry Pi, Raspberry Pi Microphone

  • ReSpeaker 4-Mic Array for Raspberry Pi（Pi 3/Pi 4 B +) is a 4 microphone expansion board for Raspberry Pi designed for AI and voice applications. This means that you can build a more powerful and flexible voice product that integrates Amazon Alexa Voice Service, Google Assistant, and so on..
  • Different from ReSpeaker 2-Mics Pi HAT, this board is developed based on AC108, a highly integrated quad-channel ADC with I2S/TDM output transition for high definition voice capture..
  • Besides, this 4-Mics version provides a super cool LED ring, which contains 12 APA102 programmable LEDs.With that 4 microphones and the LED ring, Raspberry Pi would have ability to do VAD(Voice Activity Detection), estimate DOA(Direction of Arrival) and show the direction via LED ring, just like Amazon Echo or Google Home..
  • This Raspberry Pi microphone support all Raspberry Pi models, including Raspberry Pi Zero, Raspberry Pi 1 B+, Pi 2 B, Pi 3 B, Pi 3 B+，Pi 4 B..
  • ReSpeaker 4-Mic array does not have audio output. If this is a requirement please consider the ReSpeaker 6-Mic Circular Array Kit For Raspberry Pi, the ReSpeaker 4-Mic Linear Array Kit for Raspberry Pi , or the ReSpeaker Mic Array v2.0..
Check Stock