Categories

Best Motor Driver Module

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

  • DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
  • STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
  • FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
  • PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
  • UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..
Check Stock

6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

  • ❃❃ The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Come with a standard interface, when used directly pluggable..
  • ❃❃ Drive Module Board Size(in): 1.37 * 1.18 * 0.6(in).
  • ❃❃ A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • ❃❃ 5 line 4 phase can be used for ordinary ULN2003 chip driver, Connect to the 2 phase, Support the development board, With convenient use, direct docking..
  • ❃❃ Great packing in a box : 6 PCS ULN2003 Stepper Motor + Driver Board (with a little gift)..
Check Stock

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE (no Wire)

  • 5pcs Stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface. A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • Motor diameter: 1.1 inches.Wire length：9.05 inchs. Stepping angle: 5.625 x 1/64.Reduction ratio: 1/6.Drive Module Board Size:1.26 inchsX1.38inchs. Cable length: about 20cm /8-inch..
  • Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board..
Check Stock

DEVMO 5pcs DRV8825 Stepper Motor Driver Module with Mini Heat Sink for 3D Printer Accessories Compatible with RepRap 4 RAMPS 1.4 StepStick

  • ★The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough..
  • ★Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step..
  • ★Simple step and direction control interface..
Check Stock

BIQU LCD 12864 Version Graphic Smart Display Controller Module with Adapter and Cable for RAMPS 1.4 Reprap 3D Printer Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock

3D Printer Controller Kit RepRap RAMPS 1.4 + 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display 3D Printer Controller Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock

sb components Raspberry Pi Pico Board with Pico Motor Driver HAT Connects 2 DC and 1 Stepper Motor DC Motor Control Module for Raspberry Pi Pico, Raspberry Pi Pico Kit

  • Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
  • It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
  • Pico Driver Motor HAT is a DC motor control module that is powered by one H-bridge IC L293D with the motor input supply range 6 V-24 V.
  • Pico Driver Motor HAT is specifically made to work with the Raspberry Pi Pico Board.
Check Stock

Eiechip® CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver 3D Printer Interface & Driver Modules

  • 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module..
  • The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers..
  • It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors..
  • Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors..
  • This shield can make quick work for managing stepper motors in your project..
Check Stock

3D Printer Heatsink Kit + Thermal Conductive Adhesive Tape, Cooler Heat Sink Cooling TMC2130 TMC2100 A4988 DRV8825 TMC2208 Stepper Motor Driver Module (22pcs)

  • Can be applied for passive cooling of Stepper Motor Module TMC2130 TMC2100 A4988 DRV8825 TMC2208.
  • With thermal conductive adhesive tape backing.
  • Stepper motor driver module is not included.
  • Dimension: 0.35 x 0.35 x 0.47 inch / 9mm x 9mm x 12mm (L*W*H), Weight: 0.04 oz / 1 gr per piece.
  • Includes 22 pieces blue aluminum heatsink.
Check Stock

AOICRIE 5Pcs L298N Dual H Bridge Stepper Motor Driver Board For Arduino (5pcs)

  • 【Package Included】- 2pcs L298N Motor Driver Controller Board Modules..
  • 【Item Condition】- Drive voltage 5V-35V, high working power to 46V. Large current can reach 3A MAX and continue current is 2A. Power to 25w.(NOTE: To avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.).
  • 【High Quality】- Use L298N as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module..
  • 【High Efficiency】- Dual-channel H-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
  • 【Easy of Use】- No assembly required. This L298N board comes ready to go. Just wire up motors and power, this thing will work wonders..
Check Stock

eMylo Smart RF Motor Controller Switch Relay Wireless Remote Control Switch 12V Motor Switch 433Mhz for Rolling Door, Electric Curtains/Locks, Water Pump, DC 5V-24V with 2 Transmitters （1 Pack）

  • ★ Motor wireless remote control switch: It is specially designed for motor. Two-channel design capable can control the forward, reverse and stop of the motor, and with long control distance..
  • ★ Technology Upgrade: the transmitters and receivers adopt non-directional wireless encoding technology, allowing independent control, without mutual interference, High-performance "TUYA "chip module, which stable performance, sensitivity..
  • ★ Easy Installation: Using the Special jointing clamp to connect the motor and wireless relay in one minute. No need any tools. Avoid opening the box during installation and ensure firm connection and safe operation..
  • ★ Stability & Safty: The relay module is with signal sensitivity and resist interference. RF motor controller can pass through walls, floors and doors to control receiver within the valid range. Made of the ABS material and flame retardant material, overvoltage protection and fire protection, safer..
  • ★ Widely Application: Structural upgrading eMylo motor driver reversing controller switch allowing independent control without mutual interference. Commonly used in rolling doors, electric curtains, electric door locks ,water pump and other motor machines. Start your smart life now..
Check Stock

HiLetgo BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit

  • 5V isolate with MCU, and effectively protect MCU.
  • Voltage indication of motor driver output end.
  • Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2).
  • isolation chip 5 V power supply (can share with MCU 5 V)..
  • Able to reverse the motor forward, two PWM input frequency up to 25kHZ.
  • two heat flow passing through an error signal output..
  • Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply.
Check Stock

8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot

  • Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
  • The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
  • Terminal driver part of the supply area VMS: +5V ~ +35V.
  • Drive part of the peak current Io: 2A / Bridge.
  • Logical part of the terminal power supply range Vss :4.5-5 .5V.
  • Logical part of the operating current range: 0 ~ 36mA.
  • The control signal input voltage range: 4.5-5.5V low 0V high.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
  • High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..
Check Stock