Categories

Best Oled I2c Arduino

HiLetgo 0.96\ SSD1306 I2C IIC SPI Serial 128X64 OLED LCD Display 4 Pin Font Color Yellow Blue

  • Works well SSD1306 library, a nice OLED for Arduino, Beaglebones, Raspberry Pi.
  • Simple 4-wire I/F makes it a snap to use, easy to get up and running.
  • Low-power, very legible and vibrant, a crisp screen, pixels stand out very well even in a brighter circumstances like full sunlight.
  • There are other I2C IIC(4Pin) and SPI (7 Pin) interfaces and two different Font Colors for your option.
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

AITRIP D1 Mini WiFi Dev Board,Mini NodeMcu Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini (Pack of 6)

  • （pack of 6 ）This D1 mini module is a mini WIFI board based on ESP-8266EX..
  • Our D1 mini development board is 100% compatible with Arduino WeMos and can be programmed in Compatible with Arduino IDE..
  • Support OTA on line.Compatible withArduino compatibility. Using Compatible with Arduino IDE for programming..
  • This WLAN board contains 11 digital input / output pins, all pins have interrupt / pwm / I2C / 1-wire and a micro-USB connection..
  • 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
  • 1 analog input(3.2V max input). Micro USB connection.
Check Stock

MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module White I2C OLED Screen Driver DC 3.3V~5V for Ar duino

  • ★ ★ Product Manual: Please get the link from the product description below.
  • 128x32 OLED display, no need backlight, self-illumination, Display Color: White. Plz note: These I2C OLED Display Modules come without pin headers..
  • The display performance is better than the traditional LCD display, also lower consumption.
  • I2C oled display, IIC (I2C communications) simplifies connections.
  • Use with Ar duino, ESP8266, ESP32, STM32, etc.
  • We have a Strong After-sales Service Team: As long as you have any questions about the product, we will resolve your issue immediately if received your email, your satisfactory purchase experience is our greatest hope! How to email us? Plz click “MakerFocus” and click “Ask a question” to email us! Looking forward to your consultation!.
Check Stock

Adafruit Power Relay FeatherWing [ADA3191]

  • High speed SPI display with digital I2C touchscreen driver.
  • Single-touch capacitive touch bonded on top.
  • 240x320 resolution, 18-bit GPU, 262, 000 color - our library uses 16 bit color mode. Ili9341 (data sheet) controller with built in video ram buffer.
  • We also have a touch screen library that detects x, Y and Z (pressure) and example Code to demonstrate all of it. The Code is written for arduino but can be easily ported to your favorite controller.
  • Works with any classic arduino '328. Solder closed three jumpers to use the icsp header for use with leonardo or Mega! 2.8" diagonal color touchscreen TFT.
  • Touchscreen controller requires I2C pins sda and Sca. Microsd pin requires digital #4.
  • That means you can use digital pins 2, 3, 5, 6, 7, 8 and analog 0-5. Pin 4 is available If not using the MicroSD.
Check Stock

ACEIRMC CJMCU-811 CCS811 Low Power Carbon Monoxide Air Quality Monitoring Digital Internal Gas Sensor Module Control Board I2C

  • Digital sensor for measuring changes in VOCs, in particular Carbon Dioxide (CO2).
  • Simply supply power, connect WAK to Ground, and connect the SDA and SCL pins to the I2C pins on your Arduino, ESP8266, Raspberry Pi, etc..
  • Operating voltage of 3~5VDC. 2C address 0x5A.
  • Easy to use on a breadboard with the included 8-pin header.
  • CCS811 Carbon Monoxide (CO) Breakout Board for Arduino Raspberry Pi ESP8266 I2C 3~5VDC CJMCU-811 CCS801.
Check Stock

AITRIP 12PCS TCA9548A I2C IIC Multiplexer Breakout Board Module 8 Channel Expansion Development Board for Arduino

  • The TCA9548A adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use.There are 8 I2C interfaces on one expander, and there are eight bidirectional transfer switches that can be controlled by I2C bus. This means that after 1 expander is transferred, 8 identical addresses can be connected to the same I2C port..
  • Expansion board TCA9548A compatible with IIC bus and system management bus (SMBus), active low reset input, support for hot insertion, low standby current, no glitch during power-up, support for voltages between 1.8V, 2.5V, 3.3V and 5V buses Level shifting, TCA9548A I2C IIC multiplexer breakout board depending on the contents of the programmable control registers, any single SCn/SDn channel or combination of channels can be selected..
  • 12pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino.
Check Stock

SunFounder 2004 20x4 LCD Module IIC I2C Interface Adapter Blue Backlight Compatible with MEGA2560 Arduino R3 Raspberry (2 Pack)

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each. (2 Pack).
  • Compatible with Arduino R3/Mega2560 board..
Check Stock

SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield Compatible with Arduino R3 Mega2560

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each..
  • I2C Address: 0x27 or 0x3F.Compatible with Arduino R3/2560 board. http://wiki.sunfounder.cc/index.php?title=I2C_LCD2004.
  • Professonal Support: SunFounder customer service team are always willing to solve any question from our customers .Any problem, please contact us on Amazon..
Check Stock

ACEIRMC 6pcs PCF8575 IO Expander Board Module I2C to 16IO IIC I2C I/O Extension Shield Module 16 bit SMBus I/O Ports for Arduino R3 (6pcs)

  • I2C address: 0x20(default),can be modified by soldering A1 and A2 selection pads..
  • Each pin configurable for input or output..
  • Open-drain interrupt output pin for input change interrupt..
  • New Open-Smart PCF8575 IO Expander Board Module I2C to 16IO for Arduino R3 and other MCU to control simple relay, buzzer, button, led..
Check Stock

DORHEA 10PCS 0.91 12832 IIC I2C OLED Display Module 0.91inch I2C 128x32 SSD1306 LCD Display Module White I2C OLED Screen Driver DC 3.3V/5V with 4 Pin Headers for Ardu ino

  • 0.91 inch OLED display, no need backlight, self-illumination, Display Color : White, Resolution: 128 x 32..
  • The I2c OLED display performance is better than the traditional LCD display, also lower consumption, high resolution OLED for any of your micro....
  • The 0.91 display performance is better than the traditional LCD display, it uses the very common I2C bus, and runs on the SSD1306 display driver..
  • 0.91 oled compatible with Ardu ino, ESP8266, ESP32, STM32, etc.
  • The 12832 display can run on 3.3v. It is legible, even with 4 lines of text. Highly recommended for projects that require some form of user interface..
Check Stock

HiLetgo MCP4725 12 Bit I2C IIC DAC Development Board Breakout Board Internal EEPROM Store Settings for Arduino

  • The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC)..
  • A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller..
  • On board are SCL, SDA, VCC, and another GND for your basic I2C pinout..
  • If you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.store settings.
  • Digital to analog converters are greInternal EEPROM to store settingsat for sound generation, musical instruments, and many other creative projects!.
Check Stock