Categories

Best Pcb Antennas

Yellow Sanwa LB35 Balltop for JLF Joysticks

  • Original Sanwa Denshi TP-MA Replacement PCB with Microswitches.
  • Replacement microswitch PCB for Sanwa JLF series Joysticks.
  • Often the PCB is the first to go out on a Sanwa JLF in a few years. Restore it to brand new by getting the Sawa TP-MA PCB assembly. This replaces the entire set of microswitches and PCB, and housed in very easy to install module..
  • Installation: Remove the Sanwa JLF lever restricted Remove the TP-MA board that comes from the Sanwa JLF lever Place the new board pointing in the same direction as the previous one. Finally place the restrict again.
  • Package include One pcs Original Sanwa TP-MA PCB with Microswitch.
Check Stock

VIGURTIME AM/FM Radio Kit | Soldering Project DIY Kit for Practicing Teaching Electronics | Stereo | Great STEM Project and Gift | Upgraded Version VT-16

  • 2 Kinds of Mode – AM and FM, give you more choices. Two IC chips, the main IC chip and related configuration of the radio kit have been fully upgraded, which means the radio effect would be much better..
  • A Great STEAM Project - Complete parts kit and full color instruction manual, let you or your kids can learn how to solder, get familiar with more components, learn radio schematics, and more. Not only is it a great soldering project kit, it's also a really cool radio kit when done!.
  • Stereo Effects - Yes, it comes with 2 speakers (8Ω1W) and has stereo! Flick the silver knob and are you ready to enjoy some great music from the blue stereo radio kit?.
  • Long Antennas - 4.7"/120mm long AM magnetic rod antenna for better AM reception. At the same time, the length of the FM antenna is 13.7"/350mm, which can be retracted, changed direction, more convenient for you..
  • Easy to Soldering - 16X12cm large PCB board with clear marks, clear circuit traces, high-quality components, and full-color manuals make soldering part very easy..
Check Stock

9dBi Magnetic Base Dual TS9 Antenna for Netgear Nighthawk M1 MR1100 LB1120 LM1200 Verizon Jetpack 8800L Mobile Hotpots Router MiFi Mobile AT&T T-Mobile Hotspot 4G LTE Router, Eifagur

  • Compatible with M2 (MR2100), M1 (MR1100), AC790, AC810, LB1120, LB1121, LB2120 LM1200 . Verizon JetPack AC791L, MiFi 6620L, 7730L, 8800L any 3G/4G/LTE Router, Modem or Hotspot with TS9 Antenna Jack.
  • Cable Length: 3meter/10ft Low Loss Cable.
  • Compatible Carrier Network: Verizon, AT&T, T-Mobile, Sprint and etc.
  • 4G LTE Mobile Hotspot, MiFi Router, Wireless CPE Router, Cellular Mobile Broadband Modem, USB Modem Dongle Adapter, Feature: Magnetic Base Mounting(Easy to install).
  • High-performance PCB board is used inside the antenna, and its performance is better than other copper array antennas.
  • Don't worry about any problems, we have carefully checked each product, we are willing to provide 30 days free replacement and Free return,100% Satisfaction Guarantee.
Check Stock

Arcade Fight Stick Street Fighter Arcade Joystick Keyboard control Fighting box PXN X8 For Nintendo Switch/PS4/PS3/XBOX Series X/S/XBOX S/X,PC

  • Original Sanwa Denshi TP-MA Replacement PCB with Microswitches.
  • Replacement microswitch PCB for Sanwa JLF series Joysticks.
  • Often the PCB is the first to go out on a Sanwa JLF in a few years. Restore it to brand new by getting the Sawa TP-MA PCB assembly. This replaces the entire set of microswitches and PCB, and housed in very easy to install module..
  • Installation: Remove the Sanwa JLF lever restricted Remove the TP-MA board that comes from the Sanwa JLF lever Place the new board pointing in the same direction as the previous one. Finally place the restrict again.
  • Package include One pcs Original Sanwa TP-MA PCB with Microswitch.
Check Stock

4X Prototype PCB for Arduino Mega 2560 R3 Shield Board DIY

  • Prototype PCB for Arduino Mega 2560 R3 Shield Board DIY..
  • PCB Dimension: 101.6mm x 53.34mm / 4" x 2.1".
  • PCB Thickness: 1.6mm / 0.063", Material: high quality FR-4 glass fiber PCB..
  • All holes are plated through. Top and bottom side are identical copper layers. Pads grid (pitch) 2.54mm / 0.1", hole diameter 0.9mm..
Check Stock

Zorveiio 50 Pcs PCB Board Mounting Feet with Screws, PCB Spacer Kit PCB Feet Plastic PCB Standoffs for Arcade Gaming Board Console Motherboard

  • 【Premium Material】Our pcb board mounting feet are made of high quality insulating plastics, which is sturdy, strong enough and durable in use. Such reliable plastic spacer can stay firmly on PCB Board, good insulation with long service life..
  • 【Pacakge & Suitable Size】 You will receive 50pcs L type pcb feet and 100pcs mounting screws (Each foot comes with 2 pieces screws). Each pcb standoff measures approx. 0.8" x 0.8"/21.2mm x 20.3mm, can secure the board tightly. Sufficient enough for you to satisfy using and replacing daily needs..
  • 【Widely Usage】Our plastic pcb feet are suitable for PCB packaging and stacking applications. Specially for fixing gaming boards, game console motherboard, video board, arcade gaming board ect and work well. Serve as ideal replacement hardware parts and offer you much convenience in your daily life..
  • 【Easy to install】 These pcb spacer kit is easy to install and use, you just need to tighten mounting screws in a breeze, will not need a lot of labor. It can secure the circuit board to other surfaces effortlessly..
  • 【100% Risk-Free Shopping】 Zorveiio's products are backed by incredible customer service to make sure your satisfaction is guaranteed. If you have any other questions about it, please do not hesitat....
Check Stock

Gardner Bender GSW-26 Electrical Door Switch, SPST, Normally On- Mom OFF, 16 A/125V AC, (Repl. for GSW-SK)

  • Tealio switches come in 1 variant. The spring weight is rated at "bottom out" force, not actuation! Our Tealio switches have been tweaked with wobble reduction and improved smoothness compared to regular Gateron linears..
  • 67g - Transparent, Light Teal-Blue Stem, PCB Mount [Linear].
  • Please note that PCB mounted switches can still be used in many plate mounted keyboards. As long as your PCB underneath has 2 extra holes next to the center post, it will support PCB Mounted switches and add extra rigidity to your build. If your PCB does not have the extra holes, then you can simply cut the small plastic legs off to make them Plate-Mount!.
Check Stock

GK61 GK61x RGB Hot Swap Independent Driver Tyce-C ANSI Replacable Space Cherry MX Switches Mechanical Keyboard DIY Kit Case Plate PCB

  • Package Included:Case + Feet + Screws + GK61 Hot Swap PCB + Alu Plate + USB Cable + Switch Removal Tool.
  • Pls note:The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place..
  • The chipset is MCU 32 bit,8M Flash,3 pcs 256*256*256 RGB drive to support full 16.8 million RGB..
  • PCB has RGB presoldered,it's under per switch.PCB RGB can support by music..
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again..
Check Stock

ANLI TA-1UHF Antenna Trunk Mount For SO-239 Thread Antennas

  • UHF or SO-239 Thread Trunk mount accepts Optional Antennas having a PL-259 " UHF , M or PO " base thread..
  • For Standard Sedan type Trunks. Includes 15ft RG-58A/U Coax cable with PL-259 Connector..
  • Great for Amateur radio & Two way mobile antennas having an UHF base thread..
  • Fits ANLI WH-713 and WH-717 DualBand antennas, & other " UHF" ( SO-239 ) type base thread antennas..
  • Heavy Duty with 4 Allen bolt connecton and Ability for slight angle Adjustment.
Check Stock

GK64 GK64x Keyboard kit CNC Wood Wooden Case Wired PCB Plate Stabilizers Walnut Wired PCB

  • Package Included: CNC Case + Feet + Screws + GK64x PCB + Plate + Plate stabilizers.
  • CNC Wood Case and the stabilizers is Genuine plate mounted stabilizers.
  • Built-in microphone under spacebar, support External sound source play.
  • The plate is FR4 plate which more soft and silent.You need to attach plate with PCB by switches.Install 4-5 switches to plate then to PCB socket at....
Check Stock

PCB Drill Bits Set, Micro Drill Bits Set, 50pcs PCB Drill Bit Set Spiral Flute Carbide 0.3mm-1.2mm Drill Bits for Dremel Print Circuit Board Jewelry CNC Engraving (5PCS Each) by BOOTOP

  • This PCB Drill Bit Set contains 10 different size drill bits diameter: 0.3mm, 0.4mm, 0.5mm, 0.6 mm, 0.7 mm, 0.8 mm, 0.9 mm, 1.0 mm, 1.1mm, 1.2mm. And each size have 5 pcs. Varies sizes to meet different needs..
  • This micro drill bits are designed to drill and engrave on print circuit board and other precise work. The PCB Drill Bits are made of high quality tungsten steel, highly wear resistance, high hardness, bending strength, anti-impairment, highly working efficiency. Seismic design on the blade edge enables it to stay stable during engraving..
  • PCB Drill Bits Set are great for punching at printed circuit boards, 3D Printer Nozzle Cleaning, CNC engraving plexiglass, Amber beeswax, bakelite, jewelery, metal plastic and other precision drilling.
  • cutting and engraving and worked on Acrylic, PVC, Nylon, Resin, Fiberglass,etc..
  • PCB Drill Bit With sharp cutting edge, milling groove and clean surface, these sets of tool work quickly and cleanly, no glitches or scrap left. Package with high quality plastic box, easy carry and better protection keeps the blade tip goods in the delivery from being damaged..
  • 180 Days warranty. If you are not satisfied with our products,feel free to contact us for a replacement or refund. The PCB Drill Bits may also know as micro d....
Check Stock

YMDK GK61x GK61xs GK64x GK64xs Anodized Aluminum CNC Case (Only Aluminum Case)

  • Package Included: CNC Case + Rubber Feet + Screws.
  • New GK61x GK61xs GK64x GK64xs plate and PCB can install in directly..
  • Old GK61 GK64 plate can't use since the size is bigger than normal 60 case.You can just replace a GH60 size customized plate is ok.The plate need to be compatible with GK61 PCB..
  • How to judge old and new edition: Old GK61 GK64 PCB is white and only support single 6.25u space New GK61x GK61xs GK64x GK64xs PCB is black and can support split space and single space at the same time..
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.If little keys not working,check the switch pin whether it's bent at first.Especially Kailh switches.
Check Stock

Pieces 4 Pin LED Light Strip Connectors Set Including Screw Fixing Clips, 4 Pin LED Connectors, Cuttable T, L and X Shape PCB Board for SMD 5050 RGB LED Strip Lights Gapless Solderless Connector

  • ...e to stand up to 4A current and 0 - 24V (5V, 12V, 24V) voltage, the heat resistance level is -20℃ - 100℃, so they are suitable for most non-waterproof 4 pin SMD 5050 RGB lights in 0.39 inch/ 10 mm width.
  • Note: you should pay attention to use them correctly for ensuring safety and extending service life.
  • Cuttable PCB board: the PCB board is cuttable, so you can use a cutting tool to cut T-shaped, L-shaped and X-shaped PCB board into any shape you want to facilitate the connection of various forms of light strips.
  • Just use your imagination to DIY a special light strip.
  • Please cut the LED strip according to the cuttable mark when you want to change the shape of PCB board.
  • Simple to install: the LED strip connector clip can be easily opened and closed, you can quickly slide RGB strip into the connector clip without any tool, please make sure connector + - polarity in line with + of strip before you connect it.
  • Wide range of usages: the 5050 LED strip connectors are suitable for standard density strips or DIY LED lights, for corner connection, and able to decorate Christmas trees, parties, birthdays, weddings, parties and other scenes according to your own needs.
  • Sufficient quantity: the package comes with 40 pieces 4 pin LED connectors, 15 pieces L-shape....
Check Stock