Categories

Best Pipe Heating Cable

HEATIT JHSF 60-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

HEATIT JHSF 120-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

HEATIT JHSF1 Self Regulating Pre-Assembled Heating Cable 75-feet 120V Roof deicing and Pipe freeze Protection

  • 6 ft. water pipe heating cable, 42 watt, black color.
  • Stops metal and rigid plastic pipes from freezing down to -40°F — built-in thermostat automatically turns heating on when pipe temperature is below 42.8° F (close to freezing) and turns heating off once pipe is warmed to 55.4° F (well above freezing).
  • A single 6 foot heating cable is suitable for 6 foot to 8 foot long pipes that are 3/8 inches to 3/4 inches in diameter, or for 6 foot long pipes that are 1 to 1-1/2" in diameter. NOTE: Use only for water filled plastic (including PEX) or metal pipes. Not for use with anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines, and so on..
  • Features grounded plug with indicator light.
  • Pre-assembled, easy to install using the included instructions. Materials required (not included) are: aluminum foil (recommended for plastic pipe), fiberglass plumbing pipe insulation, fiberglass tape or similar with temperature rating 175° F or higher..
Check Stock

Easy Heat AHB-112 Cold Weather Valve and Pipe Heating Cable, 12-Feet

  • Easy Heat pipe heating cable installs quickly and easily to keep water flowing.
  • Includes grounded plug, built in thermostat, and instructions.
  • Each cable consists of tough PVC inner insulation, a continuous ground braid, and weather-resistant PVC outer jacket.
  • AHB units are activated and de-activated by an integral energy-saving thermostat.
  • Approved for rigid plastic and metal pipe.
Check Stock

HEATIT JHSF 12-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • ...ture is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com)..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
  • Testing the cable before the installation. Uncoil the cable, plug in....
Check Stock

HEATIT JHSF 6-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • ...ture is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com)..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
  • Testing the cable before the installation. Uncoil the cable, plug in....
Check Stock

HEATIT JHSF 80-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • ...ture is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com)..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
  • Testing the cable before the installation. Uncoil the cable, plug in....
Check Stock

HEATIT JHSF1 Self Regulating Pre-Assembled Heating Cable 125-feet 120V Roof deicing and Pipe freeze Protection

  • ETL approved. HEATIT is registered Trademark by zhukeshi(We didn't authorize other sellers in Amazon.com). Suitable for use on plastic and metal water pipes( including inlet pipe,drain pipe, sewer, palm tree frost protection etc). Industrial grade self regulating heating cable. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Protect pipes up to 2 1/2” in diameter. For a better freeze protection, at least 1/2 inch thick or thicker insulation material is recommended, especially for extremely cold weather. If the ambient temperature is lower than -20°F(-29°C), please use 1” thick insulation material. ETL approved. 50 degrees F for pipe freeze protection.3 ft 18/3 cold lead with grounded plug..
  • Roof deicing application: HEATIT JHSF1 was designed to prevent the ice dam formation not to melt the ice dams which were already formed. Please turn on the cable at the beginning of snowing. Can be used on flat roofs, metal roofs, asphalt roofs, rubber roofs, slate roofs, stone roofs, metal roofs, ceramic....
Check Stock

HEATIT Mobile Home 100-feet HEATIT HTM Braid Self Regulating heating cable Water Line Freeze Protection

  • The self-regulating pipe heating cable system is designed for mobile home and other dry applications etc. Can be used on residential metal or plastic water supply and drain pipe freezing protection..
  • ETL approved. Tinned copper braid as the out jacket as well as electrical ground. Self regulating heating cable just deliver the heat where is need. The cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Additional tools which you may need: High quality electrician’s tape such as HEATIT glass cloth tape, 1/2” thick fiberglass insulation with vapor seal, wire cutters or heavy scissors, Phillips#2 slotted screw drivers, Ruler or measuring tape..
  • HEATIT HTM connection kit is necessary for the pipe freeze protection application. Please purchase this kit separately.If you also need the cable to be used on the valve you may need longer cable. The Maximum cable length is 75 feet. Use of longer length may cause the internal fuse to blow..
  • Quick test: Once insulation is finished, plug the cable into a 120V AC outlet. Don’t use any of the water for about 1 hour. After that turn on the tap on HEATIT HTM p....
Check Stock

HEATIT JHSF 24-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • ...ture is below 37F/3 degree C. Please test the cable in a cold environment. HEATIT is registered Trademark by zhukeshi(We didn’t authorize other sellers in Amazon.com)..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable. No worry about the overheat risk. More Safe. Can be used by straight, spiral and overlap. More functional..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off), and instructions. 120 volt, 3 watts/ft at 50 degrees F. Energy-efficient. Protect pipes up to 2″ in diameter. For a better freeze protection, at least 1/2 inch thick insulation material is recommended, especially for extremely cold weather..
  • ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. The minimum bending radius is 1 inch.Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
Check Stock

PipeMate Self-Regulating Heating Cable for Pipe Freeze Protection, 120V, 5Watts/Ft. (3 Feet)

  • Material: The roof deicing cable is made of plastic + copper core, the self-regulating temperature design is safer and energy saving, easy and reliable to use on your roof..
  • Features: Pipe heating cable 50ft(15.24 meters), no need for thermostat, this heated cable can self-limiting temperature of 65℃, greatly reducing energy waste. (no heating when the internal temperature reaches 65℃). Three pulgs in US standard to meet the circuit use of most households..
  • Function: Designed to prevent pipes from freezing and water damage caused by ice dams, from forming on roofs, gutters and downspouts. Protect your roof from damage and leaking, keep the water flowing in gutters with our heat trace cable roof..
  • Use Places: This heat trace cable is perfectly for roofs, gutters and downspouts, easy heat roof de-icing cable..
  • Installation: Can be installed by spiral, crossing, straight, etc. Easy and safe to follow instructions, no overheat risk, and will not short or burn out if the pipe heating cable is overlapped..
Check Stock

DEWENWILS Roof Heat Cable, 18ft Heat Tape for Pipe, Gutter, Roof, Self-Regulating Cable Pre-Assembled, UL Listed

  • Designed for water filled plastic (including PEX) and metal supply pipes only. Do not use on drain lines, fuel lines, hoses, empty water pipes, steam lines or gutters. Three year limited warranty. If you have any question about the product, please contact us and we will try our best to help you..
  • Quick and easy to install. Minimum pipe length is 3 feet. Cable will be applied straight along the pipe, and will protect pipe from 3/8" to 1 1/2" in diameter..
  • Save energy. 120 Volt, 7 watts/ft. 2 ft 18/3 cold lead with plug.The build-in thermostat automatically turns the heating cable on below 42.8° F (6° C) and off above 55.4° F (13 ° C)..
  • UL approved. Durable polyurethane as inner insulation and weather resistant PVC (high-low temperature) for outer protective jacket. Never allow heating cable to touch, acorss , spiral or overlap itself at any point..
  • Testing the cable before installation. Uncoil the cable, plug in the cable. Wrap a bag of ice around the thermostat. The thermostat will turn the cable on when the temperature below 42.8° F. Wait about 20 minutes. The cable should now feel warm to touch. Then turn it off..
Check Stock

TOPDURE JHSD 3-feet Pipe Heating Cable Built-in Thermostat

  • ROOF HEAT CABLE - keeping your pipe/water lines/roofs/gutters from freezing during the winter,functioning perfectly for plastic and metal pipes, all kinds of roofs, keep the water flowing in gutters.
  • SELF-REGULATING TECHNOLOGY - the cable output will change automatically depend on the ambient temperature, the output goes up when the temp is low and goes down when it's high, saving energy and electricity for you, illuminated plug lets you see if the heat cable is working from a distance.
  • HEAVY DUTY CABLE - 6FT cold lead and 6FT/18FT heat cable is commercial grade for long-time and heavy-duty usages, PVA out jacket, 5W/ft under 50°F for heating pipes.
  • EASY TO INSTALL - pre-assembled for quick installation, the heat cable can be straight-traced or spiral on the pipe, be aware that the lowest installation temperature is 14°F and the maximum exposure temperature is 221°F.
  • RELIABLE FOR HEATING PIPES - UL and ETL cerfied, illuminated plug lets you see if the heat cable is working from a distance, please test the cable before the installation, 1 Year warranty provided.
Check Stock