Categories

Best Plc Interface Module

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA)，PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock

WSDMAVIS 2Pcs PWM to Voltage Module 0% -100% PWM Converted to 0-10V Voltage Digital Analog Signal Converter for PLC Signal Interface Switching

  • The PWM transfer voltage module LC-LM358-PWM2V converts the PWM digital signals into 0 to 10V analog signals.Allowable error:5%..
  • It can be used as signal interface switching for PLC or other industrial control boards. The output voltage is regulated by adjusting the duty ratio of the PWM..
  • The modules are small in size and easy to use in different places.Easy to operate, fine tuned by potentiometer..
  • MCU embedded technology.Work Voltage:DC 12V-30V(Power requirements:> 100MA).
  • Select the PWM signal input level range through short-circuit.The peak of 4.5V to 10V level. The short cap install in ‘5V’. This level is used for normal controller or 5V MCU.
  • The peak of 12V to 24V level, so inserted in 24V. The short cap install in ‘24V’. This level is used for normal PLC controller..
Check Stock

Kuuleyn Frequency to Voltage Converter Module,1-3KHZ 0-10V PWM Signal to Voltage Converter Module Digital Analog Board

  • This module is easy to wire and convenient to use.
  • PWM converts digital signals into analog signal (0 to 10V).
  • Input digital signal can be 5V or 24V level 0-100% PWM signal.
  • Output analog signal can be 0-10v voltage or 0-5v voltage.
  • Can be used for industrial control panel PLC or other signal interface switching.
Check Stock

Isolation Amplifiers 4.5 - 5.5 SV 8 dB (50 pieces)

  • ★【WORKING PRINCIPLE】Effectively avoid system instability caused by mutual interference..
  • ★【EXCELLENT QUALITY】Made of high-quality electronic components, stable and reliable performance..
  • ★【PROTECTIVE FUNCTION】Can be used to protect PLC internal relays.Effectively protected the output nodes of the PLC..
  • ★【PERFECT REPLACEMENT】Can directly replace traditional relays, reducing maintenance time and costs..
  • ★【EASY TO USE】Hole punching and PCB module mounting are more convenient..
Check Stock

1pcs 1-Bit AC 220V Optocoupler Isolation Module

  • Output TTL level can be detected with the microcontroller. The power supply can be 3-5V.
  • the PLC input terminal of the PLC COM power supply 24V input termination of the board signal output OUT, optocoupler board GND power negative.
  • When the power module in the power of the board after the white wire frame can not touch any device .. because it is high voltage. Note the safety of electricity.
Check Stock

Fafeicy 12-Channel DC12-36V PLC Signal Amplifier Board Isolation Relay Module Amplifier Board with NPN Input PNP Output

  • Protection function: The relay can effectively avoid system instability caused by mutual interference, effectively protect the output node of the PLC, ensure the normal transmission of the signal, and thereby protect the relay..
  • Uses: The relay module can be used to protect the PLC internal relays, which can directly replace traditional relays, reducing maintenance time and cost.
  • Stable performance: The signal amplifier is made of high-quality electronic components with stable and reliable performance..
  • Easy to install: It is recommended to design to make drilling and module installation more convenient..
  • After-sales service: We strive to provide you with the highest quality product and the best customer experience, if you're not entirely satisfied, please just feel free to contact us at any time..
Check Stock

WinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR

  • 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
  • Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
  • Standard interface can be directly connected with microcontrollers..
  • Red working status indicator for power on indication.Green working status indicator for relay the switch..
  • It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

Xiuxin 2pcs 5V 8 Channel Relay Module Board for Arduino PIC AVR DSP ARM

  • 2pcs/lot 8 Channel relay module board, Working voltage: 5V.
  • This board is for Arduino PIC AVR DSP ARM.
  • Support all single-chip microcomputer control,Industrial circle,PLC controller,Household intelligent control.
  • Relay output maximum contact is AC250V 10A and DC30V 10A.
  • Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

YVO Optocoupler Isolation Board,4 Channel Optocoupler Isolation Module PLC Signal Level Voltage Conversion Board,Can be Used for Signal Isolation,Signal Level Voltage Conversion (24V to 5V)

  • 【Widely Use】: Our optocoupler isolation board can be used for signal isolation, PLC signal level converting, level conversion between single-chip microcomputer, PLC and other signals, PNP / NPN signal to NPN signal, signal level voltage conversion and other purposes..
  • 【20K Limit Switching Frequency】: The maximum switching frequency of our optocoupler isolation is 20K..
  • 【Easy To Recognise】: Each channel of our optocoupler isolator module has been equipped with indicator, easier to recognise the working status..
  • 【Size Parameters】: Module Dimensions: 72*55*18mm (length*width*height). Mounting Hole Size: 64*47mm. Mounting Hole Diameter: 3mm..
  • 【SHOPPING WITH CONFIDENCE】: We are committed to providing you with quality services. If you have any question, please feel free to contact us by sending emails.We will provide after-sales service until you are satisfied..
Check Stock

DC12-36V 16 Channel PLC Amplifier Board,PLC Signal Amplifier Board,Isolation Relay Module,NPN Input PNP Output,Drilling,PCB Module Rack Installation

  • Can be used to protect PLC internal relays..
  • Effectively avoid system instability caused by mutual interference..
  • Effectively protected the output nodes of the PLC..
  • Can directly replace traditional relays, reducing maintenance time and costs..
  • Hole punching and PCB module mounting are more convenient..
Check Stock

Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp

  • ★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
  • ★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
  • ★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
  • ★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
  • ★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..
Check Stock

XpressKit XKLOADER2 2nd Gen Computer Programming tool

  • Xpress Kit USB Computer Interface between PC and Programmable Vehicle Interface Module (DEI Install Bypass Essentials.
  • 2nd Generation XPRESSKIT Computer Programming Tool.
  • USB Computer interface acts as a bridge between your PC and an upgradeable vehicle interface module.
  • XKLOADER2 is the 2nd generation USB computer interface (Bootloader) that acts as a bridge between your PC & an XPRESSKIT upgradeable vehicle interface module..
  • More powerfulencryption scheme, faster download speed and higher current outputDirect Plug and playcompatible with the newCANMAX400 and CANMAX400DEI SeriesPlug &XKLOADER2 is the 2nd generation USB computer interface (Bootloader) that acts as a bridge between your PC & an XPRESSKIT upgradeable vehicle interface module..
  • More powerful encryption scheme, faster download speed and higher current outputDirect Plug and play compatible with the new CANMAX400 and CANMAX400DEI SeriesPlug &.
Check Stock

ElecLab Raspberry Pi Touchscreen Monitor 7.4 Inch HDMI Capacitive LCD Display 1280x400 Speaker Case for Raspberry Pi 4B 3B+ 3B 3A+ 2B B+ (7.4inch 1280x400)

  • This display only supports the Raspberry Pi DSI interface, and the Raspberry Pi can be easily installed on the back of the monitor through 4 positioning holes. The display provides power to the Raspberry Pi through the power adapter board, and the two XH2.54 sockets can supply power to fans or other peripherals..
  • DSI interface 7-inch LCD 800x480 resolution and 5-point capacitive touch screen, display brightness can be adjusted by potentiometer and software PWM, integrated audio amplifier and 2W dual channel stereo speakers and volume potentiometer..
  • Reserve an SSD adapter PCB mounting location for running Raspbain directly from a USB3.0 SSD, or as a high-speed mass storage device as a media library for NAS or Volumio..
  • Integrated with CH340E chip and DB9 male header, RS232 or RS485 function can be selected by DIP switch. The TXD/RXD signal has LED indicators to show the communication process of sending and receiving. Can be connected to PLC, stepper/servo drive, LORA module....
  • The display is equipped with 2 damping shaft brackets, the display angle can be adjusted arbitrarily, and the brackets can also be removed to install the case. The STL file for the 3D printed case is available under eleclab-rpi/7INCH_DSI_DISPLAY, and the fan case STL file is ....
Check Stock