Disconnect Clip Set for Pipe Fitting - Push Fitting Tool for Slip Removal - Disconnect Clip Removal Tool Set - 1/2", 3/4", 1/4", 3/8" and 1" Slip Fitting Removal Tools (Pack of 5)
- : This push fitting removal tool does not require any additional materials or equipment for the installation process. Achieve a connection devoid of leakages in mere seconds..
- - : This TigerBite plumbing tool can be used for a variety of different pipes. Whether you need to work on copper tubing, PEX fitting or CTS CPVC, this tool will work without any issues..
- : The package of plumbing tools you receive includes a 1” disconnect clip, 1/4” disconnect clip, a ¾” disconnect clip, a 3/8” disconnect clip, as well as a ½” disconnect clip and a push-fit installation tip..
- : With the help of this lead-free TigerBite plumbing tool set, you can re-use fittings and valves and even rotate the fixtures so that you can reassemble them to install them in tighter places..
- : TigerBite fittings are certified up to 93 degrees Celsius and can be used at 200 PSI. They are also certified to ANSI/NSF T61 and ASSE 1061..
Check StockTecmolog Brass Pipe Fittings Connector G 1/2 Female Thread (Metric BSP) to US 1/2 NPT Male Thread Pipe Fitting Converter Adapter, SBA037
- BSP to NPT Adapter: Metric BSP 1/2" (G) female to NPT 1/2" male pipe fitting converter, easily change from standard EU metric to US inches.
- Brass Pipe Fittings 1/2: This adapter is made of brass for resistance to corrosion, ductility at high temperatures, and low magnetic permeability.
- Rubber Washers and Teflon Tape for a Perfect Seal: Come with an o-ring for the G1/2 side and the 1/2 " NPT side to produce a leak free connection.
- Connect Hoses or Fittings of US plumbing: This is used to adapt the plumbing to NPT on bath or kitchen fixture, and European hose fittings.
- Easy to Install: It has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench.
Check StockISPINNER 15pcs 1/2 Inch Stainless Steel PEX Cinch Clamps, Crimp Rings Pinch Clamps for PEX Tubing Pipe Fitting Connections, Pack of 15
- HIGH QUALITY MATERIAL - Made of 304 Stainless Steel, has good corrosion resistance, heat resistance, low temperature strength and mechanical properties..
- 360-Degree SEAL PROTECTION - These interlocking rings form a complete 360- Degree watertight seal, provide reliable and fast connection of all PEX pipes fittings..
- WIDE APPLICATION - Widely used in all plumbing system, such as water heater, air condition system, pipeline system, hydronic heating system, electrical plumbing etc..
- EASY INSTALLATION - Slip these pex clamps over the tubing, then slip tubing onto insert fitting. Use the correct cinch tools to close the clamp ear until it is fully engaged. Providing a strong, leak-free and reliable crimp fitting connection..
- SIZE - 1/2 inch PEX clamps, fit for 15.0-17.5mm outside diameter pipe. Width x Thickness of 1/2 inch clamp is 7.0 x 0.8mm..
Check StockCVS 50 PCS 3/4 Inch PEX Cinch Clamp Rings, Stainless Steel Pex Fittings Crimp Rings Pinch Clamps for PEX Tubing Pipe Fitting Connections (3/4 Inch)
- HIGH QUALITY - Meet ASTM F2098 requirements. Made of 304 Premium Stainless steel material. Salt resistant, anti rust, anti-corrosion..
- EASY INSTALLATION - Slide the 3/4 inch PEX cinch clamp ring over the pipe, push the pipe onto the fitting and squeeze with your clamp tool. Providing a strong, leak-free and reliable crimp fitting connection..
- WIDELY USED - Conversancy Brand products’ quality and performance is field-proven. Special design for all PEX pipe connection fittings. Universal used in any brand of crimp PEX pipe fittings or tubing..
- CERTIFIED - Meet the same standards for all commercial and residential plumbing applications - Hydronic heating system, air condition system, water heater, Telecommunications electrical plumbing, food pipeline system etc..
- SIZE - 3/4 inch (23.3mm) PEX clamps, fit for 3/4 inch PEX pipe..
Check StockBeduan Brass Compression Fitting, Insert Tube Support Compression Sleeve Fitting 1/4\ Tube ID (Pack of 10)
- ...ing in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
- ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing..
- ✅[QUALITY AFTER-SALE SERVICE] If you do not satisfy with our products or if you have any questions, please come to us for help. We would work out a satisfactory solution to your problem. 12 hours response service!.
Check StockHilitchi 8Sizes Tube OD 4mm-16mm Brass Compression Sleeves Ferrules Compression Fitting Kit Metric 220Pcs
- ...ng in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
- ✅ [APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing..
- ✅[QUALITY AFTER-SALE SERVICE] If you do not satisfy with our products or if you have any questions, please come to us for help. We would work out a satisfactory solution to your problem. 12 hours response service!.
Check StockHilitchi 3Sizes Tube OD 1/4 5/16 3/8 Brass Compression Sleeves Ferrules Compression Fitting Kit (SAE, 105Pcs)
- ...ing in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
- ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing..
- ✅[QUALITY AFTER-SALE SERVICE] If you do not satisfy with our products or if you have any questions, please come to us for help. We would work out a satisfactory solution to your problem. 12 hours response service!.
Check StockJeemiter Castle Nut Removal Wrench for Nut Removal and Tighten for pipe fitting and collet nut
- Material: Heat Treated High Carbon Steel / Case Hardened and Black Powder coated.
- Fits all commercial and standard Castle nuts with a 1 1/4” OD and plumbing..
- Commonly used for plumbing, pipe fitting, fishing rods, safes, automotive suspension, and hitch.
- Very easy to hang on you with the O ring end, smart and handy to use with a circle edge bar.
Check Stock100 PCS 3/4 Inch PEX Cinch Clamps, 304 Stainless Steel PEX Fitting Clamps Pinch Clamps Ring Crimp Rings for PEX Tubing Pipe Fitting Connections (Silver -3/4inch(100PCS))
- ...l design for all PEX pipe connection fittings, Interlock Rings with 360 Stepless Design. This stepless ear clamp conforms to the ASTM International F2098 standard for securing PEX tubing to insert fittings. Universal used in any brand of crimp PEX pipe fittings or tubing..
- ✔【WIDE APPLICATION】Widely used in all plumbing systems, such as water heater, air condition system, pipeline system, hydronic heating system, electrical plumbing, etc. PEX barb fittings are compatible for potable water distribution and hydronic heating applications. Providing a strong and reliable crimp fitting application..
- ✔【EASY INSTALLATION】Pex clamp rings slide the 3/4 in. clamp ring over the pipe, push the pipe onto the fitting and squeeze with your clamp tool to make a secure connection..
Check StockiSpring WSP-50SL Reusable Spin Down Sediment Filter/w Siliphos, Alternative Descaler or Softener, Hot Water System Protector, 50 Micron
- High impact stainless steel mesh filter screen with a pore size of 50 microns. The ideal first line of defense for finer filters, or expensive plumbing appliances..
- Includes Siliphos to help prevent scale and stop corrosion, greatly extending the life of your plumbing fixtures. It is recommended that the filter to be replaced every 3-6 months to prevent scale from building up..
- See through housing offers easy visual monitoring.
- Stainless steel body with 1-year warranty. Lifetime support from iSpring in Alpharetta, GA at (678) 261-7611.
- Double threads on both ends: 1 inch MNPT and 3/4 inch FNPT, flush out valve has garden hose barb fitting.
Check StockJeemiter Castle Nut Removal Wrench for Removal and Tighten Collet Nut Floor Heating Pipes Cars Walnut and Pipe Fitting
- Fits all commercial and standard Castle nuts with a 1 1/4” OD and plumbing..
- Material: Heat Treated High Carbon Steel / Case Hardened and Black Powder coated.
- Commonly used for plumbing, pipe fitting, fishing rods, safes, automotive suspension, and hitch.
- Very easy to hang on you with the O ring end, smart and handy to use with a circle edge bar.
Check StockVinco s - OsteoSheath4 - 120 Tablets by Vinco
- Package Including: 20 Ft Braided Fuel/Oil/Gas Line Kit(10pcs 6AN hose fitting + 20Ft AN6 Stainless Steel Oil line).
- Universal Application: The fuel line hose is capable of handling nearly every plumbing task on your car and is safe to use with fuel, oil, water,gas....
- Hose Material: Nylon and Stainless Steel Braided + CPE Synthetic Rubber.
- The fitting is made of T6061 Aluminum,high strength and good durability..
- Working Temperature: -40 F to +248 F. Working Pressure:500 PSI.
- Excellently Sealed,100% no leaking .Exchange or return if leak..
Check Stock
Compression Sleeve Puller Tool Remove Ferrule & Nut Of Pipe, Ferrule Puller For 1/2” Copper Water Compression Sleeve & 1/2-Inch Copper Tubing, Plumbing Tools Compression Ring Removal Tool
- ... walls, which effortlessly pulls the nut and ferral off of the pipe. This compression sleeve puller removes 1/2-inch copper water compression sleeve. If you are in need of replacing a quarter turn valve on a dishwasher, sink or toilet that has compression fittings, buy this tool and make your life easy. Designed by plumbing professionals. Precision machined plumbing tool..
- 【Not Need To Cut Off The Pipe】Saves a lot of time around cutting old pipes. Re-designed bullet nose will not pull off and is easy to use in relatively tight spots. Especially if you don’t have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. No damage to the copper. Makes removing a ferrule simple, and makes plumbing work simple..
- 【Work On Corroded & Frozen】Even such as the existing valve was severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe. Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. Easy and fast solve the problem of compression valves failing with small....
Check Stock
