Categories

Best Poe Pse Module

UCTRONICS PoE hat for Raspberry pi

  • For Pi 4 and 3 B+: This PoE HAT can be used to deliver clean and reliable power to the raspberry pi 3 model B+ and raspberry pi 4 model B (not included)..
  • Intelligent Temperature Control: the 25mm×25mm brushless cooling fan will turn automatically when the temperature of the processor is high..
  • Smaller Size: Save more space than the official HAT, can be held in the most case for Raspberry Pi.We recently released a new version of PoE HAT with fan, which can support 48V non-standard switches, please search B09MCGFX12.
  • NOTE: The network switch or power sourcing equipment (PSE) is needed to supply the PoE signal, and they must be compliant with the IEEE 802.3af or 802.3at PoE standard, particularly section 33.4.1 with regards to PSE electrical isolation of the leads. For the non-isolated switch, such as some Ubiquiti switches can not provide proper isolation, they can only work with CAT 5E and CAT 6E network cable..
Check Stock

StarTech.com 1 Port 2.5Gbps PoE Network Card, PCIe Ethernet Card w/RJ45, 30W 802.3at PoE NIC for Desktops/Servers, Network PoE LAN Adapter w/Low-Profile Bracket, NBaseT, Windows/Linux (ST1000PEXPSE)

  • 2.5G NETWORK CARD WITH POE: This PCI Express x1 Network Card enables 2.5Gbps network speeds and supplies (PSE) 30W PoE over a single CAT5e (or later) cable - Leverage existing copper cabling without the use of a Power over Ethernet (PoE) injector.
  • POE+ COMPLIANT: Card provides up to 30W PSE and 25.5W PD at 48V DC to a connected device - Supports IEEE 802.3af (PoE) and 802.3at (PoE+) to power remote devices such as access points, RFID readers, and IP cameras.
  • MULTI-GIGABIT CONNECTIVITY: The Network PoE Card features 2.5GBASE-T (802.3bz) and will auto negotiate to the connected device's highest possible speed - The PCIe Network Card supports Wake-on-LAN and RealWoW for remote wake up of the host computer.
  • TECH SPECS: 2.5Gbps/1Gbps/100Mbps/10Mbps - NBASE-T - 1x RJ45 Port - Realtek RTL8125B - IEEE 802.3af/at - 802.3az EEE - PCIe 2.1 x1 - SATA & SP4 Power Connectors - Link/PoE LED Indicators - 16K Jumbo Frame - VLAN - PXE Boot - Full and Low-Profile Brackets.
  • VERSATILE POE NETWORK CARD: The PCIe Ethernet Adapter supports Windows and Linux - Variable speed options and includes a low-profile bracket for Small Form Factor (SFF) systems ensures compatibility of the PoE NIC with current and legacy devices.
Check Stock

NOYAFA Advanced Network Cable Tester With PoE& NCV & Lamp For CAT5e/CAT6/CAT6a, Multifunction Wire Tracker Cable Tester For Tracker Underground Telephone Line Finder Home Repair

  • Main Function : Detecting PoE voltage, current, power, PSE standards Power supply modes, Verify RJ45 cables.
  • 1. Three scan modes selectable: AC filter mode/ Analog mode/ PoE mode.
  • 2. Detect AC voltage presence (50V-1000V). Test physical status for STP, UTP lan cable..
  • 3. Measure cable length accurately , the range is 120m..
  • 4. Hub blink for locating network port by the flashing port light on Hub / Switch. Available to 10M/100M/1000M Hub/ switch..
  • 5. PoE testing : identify which pins are providing power and detect how much voltage, identify which the type of PSE (at/af standard).
Check Stock

Cisco SG250-08HP Smart Switch | 8 Gigabit Ethernet GbE Ports | 45W PoE | Limited Lifetime Protection SG250-08HP-K9-NA

  • ETHERNET PORT CONFIGURATION: 8-port 10/100/1000.
  • POWER OVER ETHERNET: 8 PoE ports with 45W total power budget, PoE, PoE plus, PoE PD/PSE port.
  • CONFIGURATION AND CONTROL: Easy-to-use on-box WebUI, CLI offers basic plus capabilities, SNMP, Cisco FindIT Network Manager, PnP, auto-discovery,....
  • L2 plus FEATURES AND SECURITY: Static routing, VLANs, QoS, Voice VLAN, MSTP, IGMP Snooping Access Control List (ACL), 802. 1X, DoS prevention, SSH/SSL.
  • PEACE OF MIND: Limited lifetime , one year of technical support, and free software fixes for the term of the.
Check Stock

LoveRPi Compact PoE HAT with PWM Fan Controller for Raspberry Pi 4

  • COMPACT RASPBERRY PI 4 POE HAT: Ideal for non-grounded installation, this NON-ISOLATED PoE HAT features optimized footprint. Must be used with a standards compliant IEEE 802.3af PoE or 802.3at PoE+ switch that complies with Section 33.4.1 for power sourcing equipment (PSE) electrical isolation. "Passive PoE" (DC 24V or 48V) is not standards compliant and may cause damage to equipment if connected improperly. Some Ubiquiti switches are not properly isolated and require isolated PoE HATs..
  • GROUND LOOPS WARNING: Do not use this device with grounded USB peripherals, HDMI displays, and attachments. Please use the professional PoE model with isolation transformer to prevent electrical loops. In non-controlled PoE applications, ALWAYS use the professional PoE model..
  • INTEGRATED PWM FAN CONTROLLER: Based on the EMC2301 SMBus compliant fan controller, this PoE HAT is fully programmable over I2C to control standard 4-pin PWM fans. Set user-space or device-tree based temperature or event triggers for complete fan control from off to maximum RPM. Fan speed tach also provides stall detection, spin-up control, and ramp rate control with 1% accuracy from 500-16K RPM..
  • VENTILATED CASE WITH FAN HIGHLY RECOMMENDED: Do not use this product in an enclosed case without acti....
Check Stock

UCTRONICS PoE HAT for Raspberry Pi 4 with Case, 802.3at Power Over Ethernet Expansion Board for Pi 4 B Board, with Cooling Fan

  • Perfect for Pi 4: This PoE HAT can be used with Raspberry Pi 3 model B+ and Raspberry Pi 4 model B (not included). Please contact us if you received wrong pieces, we will send you a new case kit ASAP..
  • Higher Output Power: DC 5V (3A Max) / 12V (2A Max) via on-board terminal block.
  • Over-temperature Protection: The 25mm×25mm brushless cooling fan will turn automatically when the temperature of the processor is high..
  • Well-ventilated Case: Cut-outs for every port of Pi 4 board and PoE hat, easy to access to all ports as well as supplying well-ventilated environment..
  • NOTE: PSE (Power Supply Equipment) is needed to supply PoE signal to the Raspberry Pi, such as a PoE switch or injector..
Check Stock

Tenda 8 Port Fast Ethernet Switch（S108）| Desktop Ethernet Splitter | Ethernet Hub | Plug and Play | Fanless & Quiet | Unmanaged

  • 6 kV Lightning Protection: The switch offers various safety and protection types, including 6 kV lightening protection, PSE short-circuit protection, PoE overload protection, surge current protection etc..
  • Dual Uplink Port: With two 10/100Mbps uplink ports, the switch can meet the current demand for uplink bandwidth with NVR and router connection..
  • Standard PoE Power Supply: The switch support IEEE 802.3at/af standards. The entire switch offers a maximum PoE power output of 58 W, and 30 W for a single port, to supply power to and data transmission with IP cameras..
  • 250 m Data Transmission:I t supports extend mode and one-key VLAN. The hardware DIP mode switch makes long distance transmission effortless..
Check Stock

POE IP Camera POE Network Camera ModuleBlueFishcam IP Security Board Camera for DIY/Repair/Upgraded (2MP, 3 Lenses)

  • 2MP 1080P POE IP board Camera network Security camera module 2.8mm,3.6mm & 6mm fixed lenses Hidden Camera Indoor Security Surveillance Motion Detection for DIY/repair/upgrade.
  • Advanced H.265X/H.264 video compression,Super low rate,high definition quality of image.
  • Support various mobile monitoring(iPhone,Android).
  • Support POE IEEE8023af/at, And it's with additional assisted power supply. Power supply required: 12V 2A or above 2A.
  • Package content: 1 piece of POE mini IP board camera/network camera module..
Check Stock

Network Cable Tester, Poe Cable Tester for CAT5e/CAT6/CAT6a, Ethernet Network Tester with NCV, NF-8209 Network Cable Tracker, Test Fault Distance Location and Length Measurement by TDR

  • ▶【Three scan modes】AC filter mode/ Analog mode/ PoE mode.
  • ▶【PoE testing】Test the information of standard PoE device, such as POE voltage, power supply polarity, power supply mode and also the type of PSE(af or at standard)..
  • ▶【Hub blink】Locate network port by the flashing port light on Hub / Switch. Available to 10M/100M/1000M Hub/ switch..
  • ▶【Length measurement】Cable length testing accuracy can be up to 98% and 200 m..
  • ▶【Cable continuity testing & NCV】Test physical status for STP, UTP lan cable. Detect AC voltage presence (50V-1000V)..
Check Stock

AuviPal 802.3af/at Compliant PoE Splitter (2 Pack), PoE to Micro USB 5V Power and 100Mbps Ethernet Adapter for Raspberry Pi, Fire TV Ethernet Adapter, Chromecast, Wyze Cam v2, Arlo 2 Pro, NanoPi

  • Deliver DC 5V 2.4A Power and up to ultra-fast 100M Ethernet data for raspberry pi simultaneously, No need for a nearby AC outlet anymore..
  • Original from AuviPal with 10/100Mbps wired fast speeds which gives you a full speed of your internet, Ideal for providing both power and Ethernet for Raspberry Pi 1B, 1B+, 2B, 3B, Not for latest model 3B+, Please search "B07PNQC25X" on amazon for 3B+..
  • It utilizes the optimal PoE module solution with Isolation transformer + Standard PD (Powered Devices) chip. Run your Raspberry Pi more stable and safer when compared with others cheap non-isolated transformer and diode PD module..
  • PoE HAT Alternative - a cost savings way to achieve POE function for your Raspberry Pi instead of buying an overpriced PoE HAT, What’s more, no need to dismount raspberry pi case or add-on screen anymore by using AuviPal PoE Splitter..
  • Fully complies with IEEE 802.3af/at standard, Work with all IEEE 802.3af/at compliant PoE switch and PoE Injector (Not included). Plug and play, no extra effort or configuration required, Set it up in seconds..
Check Stock

Tenda Layer-3 Managed PoE Switch|24 Port GE Ports| 4x1G Base-X SFP| 1 Console Port | VLAN | QoS | DHCP Snooping TEG5328P-24-410W

  • 【Layer-3 routing protocol】：Supports Layer-3 static routing protocol, meeting the demand of the 3-layer networking environment in which Layer-3 networks should be interconnected while Layer-2 networks should be isolated, thus realizing an efficient and fast layer-3 routing forwarding.
  • 【410W PoE power supply】：Offers 24 gigabit PoE ports complaint with IEEE 802.3af and IEEE 802.3at. With a maximum 370 W PoE output power of the whole switch, and a maximum 30 W PoE output power of a single port, the switch helps provide stable power and data transmission for gigabit WLAN and high definition digital monitoring devic-es.
  • 【Sound security features】：Supports IP address filtering, MAC address filtering, ARP filtering, DoS attack defense, and ACL access control list, improving network security.
  • 【Dual 6 kV professional lightning protection】：Provides dual 6 kV port and power lightning protection, and supports multiple protection features, such as PSE short circuit protection, PoE overload protec-tion, power over-temperature and overvoltage protection, and surge current protection.
  • 【Lifetime free tech-support】 - Tenda provides an industry-leading 3-year with FREE lifetime 24/7 dedicated tech-support team Call us at (800) 570-5892 or email us....
Check Stock

waveshare Original Raspberry Pi Compute Module 4 IO Board for All Variants of Compute Module 4,with Real-Time Clock Dual MIPI DSI/CSI Interfaces,USB Connectors

  • The Compute Module 4 IO Board is a companion board for all variants of Raspberry Pi Compute Module 4(supplied separately). It is designed for use both as a development system for Compute Module 4 and as an embedded board integrated into end products..
  • The Compute Module 4 IO Board is designed to allow you to create systems quickly using off-theshelf parts such as HATs and PCIe cards, which might include NVMe, SATA, networking, or USB. The major user connectors are located along one side to make enclosures simple..
  • Connectors: Standard Raspberry Pi HAT connectors with PoE support. Standard PCIe Gen 2 x1 socket. Various jumpers to disable specific features, e.g. wireless connectivity, EEPROM writing..
  • RTC : Real-time clock with battery socket and ability to wake Compute Module 4 Video: 2 x MIPI DSI display FPC connectors (22-pin 0.5 mm pitch cable) Camera: 2 x MIPI CSI-2 camera FPC connectors (22-pin 0.5 mm pitch cable).
  • USB: 2 x USB 2.0 connectors. Micro USB socket for updating Compute Module 4. Ethernet: Gigabit Ethernet RJ45 with PoE support..
Check Stock

8MP POE IP Camera with IR-Cut POE Network Camera Module BlueFishcam 4K IP Security Board Camera for DIY/Repair/Upgrade (8MP-4K, 3.6mm)

  • 4K Board IP camera module 8MP POE camera network Camera Module with 3.6mm fixed lens for DIY.
  • 1/2.8” Ultral Low-illumination Progressive Scan CMOS, 4K 8MP high resolution3840*2160 @ 20fps..
  • Embedded Web Server, support Internet Explore monitoring, configuration, upgrade, H.265/H.264 high compression , two simultaneous video streams.
  • Package: 1 piece of POE IP board Camera for DIY. It's with POE function, you can use normal power supply,too. Power required: DC 12V 2A.
Check Stock