Categories

Best Power Led Module Strip

DC 12V LED Power Supply Driver Transformer - Lustaled 15W Waterproof IP67 120VAC to 12V DC Converter Constant Voltage LED Switching Power Supply for LED Strip Lights, G4 MR11 MR16 LED Display (2-Pack)

  • [DC 12V LED Power Supply]: Mini size 15W LED driver transformer, Input: AC100-265V, Output: DC 12V.
  • [Wide Application]: Our 15W LED power supply driver is suitable for most of devices with DC12V such as CCTV, Illuminated Module Signboard, Cabinet Lights, LED Strip Lights, LED Display, LED Module, Indoor/Outdoor Deck Lights, Indoor Stair Step Lights, LED Light Bulbs like G4, MR11, MR16 LED bulbs..
  • [Good Heat Dissipation]: LED 12V transformer is made of aluminum, easy for heat dissipation and ensure stability. 100% Waterproof IP67 protect for outdoor use.
  • [Safer Design]: This DC 12V LED driver is flicker-free output, thermal overload, over current, over voltage and short circuit protection built in.
  • [Note]: Please confirm whether the input voltage (AC100-265V) can work in your place before purchase the 12V switching converter, please make sure the power is lower than or equal to the rated power supply, otherwise it may burn..
Check Stock

GPIO Status LED Terminal Block Breakout Board for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

  • GPIO status LED and power 5V / 3.3V indication..
  • GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
  • Support for Raspberry Pi A+, 3A+, B+, 2B, 3B, 3B+, 4B.
  • Terminal block pitch 3.5mm, wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion pin header, height 8mm..
  • Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not include Raspberry Pi module).
Check Stock

Electronics-Salon Screw Terminal Block Breakout Module, for Arduino MEGA-2560 R3.

  • Terminal Block Breakout Module - for Arduino MEGA-2560 R3. the item has been soldered and assembled..
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
  • With power on LED indicating. red reset button on the side. with a ICSP adapter connect header..
  • FR-4 fiber glass PCB, dual copper layers..
  • NOTE: the item not include Arduino Mega module.
Check Stock

Screw Terminal Block Breakout Shield Module for Arduino UNO R3

  • Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
  • Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
  • With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
  • NOTE: the item not include Arduino Uno module..
Check Stock

30 Channel DMX decoder 512 RGB LED Strip Controller DMX dimmer DC9V-24V 2A/CH

  • 2A each channel max 60A , Maximum power load: 720W (12V) 1440W (24V).
  • RGB 30 Channel,8 group, use for LED strip,LED module,LED light.
  • 100% SATISFACTION SERVICE - No matter what reason cause dissatisfaction, we’ll send replacement or reimburse you back!.
Check Stock

GIDERWEL 12 Channel DMX Decoder RGB LED Controller 60A PWM DMX512 Dimmer Driver for RGB LED Strip and LED Module Light DC12V-24V

  • Receives standard DMX-512 digital control signal and transformrd it into PWM signal to adjust LED Lights.
  • Automatically adapt to DC5V-24V,Maximum power load: 300W (5V).
  • Aluminium housing,And High Power Output Max 60A For 5A Each Channel (5A*12 CH).
  • The DMX address can be set through dip switch,And You could connect with DMX digital console to achieve RGB dimming functions.
  • Easy Use for 4 Group RGB LED Strip,LED module And LED lights..
Check Stock

POWLAB SMD5050 Storefront Lights, 120Ft Store Window LED Lights 240Pcs 3 Led Module Light RGB Storefront Window Strip Light Super Bright Waterproof for Business Store Light Letter Advertising

  • Super Bright LED Module Light- The led storefront light uses 3pcs premium SMD5050 LED beads for each module, which offers stable & bright lights to your store front, shop, advertisements or advertising letter signs. There are 7 colors with the light: red, green, blue, purple, yellow,white, light blue..
  • Commercial LED Light- IP68 waterproof LED module lights with sticky Self-Adhesive tape on the back of each module, It is convenient for you to install with sticky self-adhesive tape on the back of each module. You can also hang them on anywhere you want with optional screw holes.DIY your own LOGO or Lighted Store Signs..
  • Store Decorative Light - Upgrade 5050 SMD module are brighter. With ABS plastic material, The Waterproof LED module lights can work normally when it rains or snows, and it will not cause a short circuit. But you should pay special attention to the positive and negative poles of the wire to avoid short circuit. Besides, the color of the plastic will not gradually become yellow after long-term using..
  • Energy-saving LED Light- The working voltage of this super bright LED light is DC 12V.
Check Stock

CZH-LABS Screw Terminal Block Breakout Board Module for BeagleBone Black.

  • Terminal Block Breakout Module - for BeagleBone, BeagleBone Black, BeagleBone AI, BeagleBone Black Wireless, BeagleBone Green, BeagleBone Green....
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
  • With power on LED indicating, with Power, Reset and Boot buttons on the side. The item has been soldered and assembled..
  • NOTE: the item not include BeagleBone Black moudle..
Check Stock

iJDMTOY (1) 12V Wired Control Module w/ Solid, Strobe and Flash Features Compatible With Car, Boat, Household LED Strip or LED Bulb

  • Solid light up function (LIGHT), (4) Strobe flashing patterns (MODE), Flashing speed control (SPEED/BRIGHT).
  • Simply tap the LED (+/-) side to LED strip or any LED lights and then tap the 12V (+/-) side to 12V power.
  • Module Box Size: 1.75" (L) x 0.50" (W) x 0.15" (H).
Check Stock

LED Driver 100 Watts 24V DC Low Voltage Transformer， Waterproof IP67 LED Power Supply, Adapter with 3-Prong Plug 3.3 Feet Cable for Any 24V DC led Lights, Computer Project, Outdoor Light

  • LOW VOLTAGE TRANSFORMER: LED Driver Power Supply 12V, 36 Watt, Input: AC100-240V, Output: DC 12V, Size: 4.92*1.38*0.91 inches, IP20 Waterproof..
  • GOOD HEAT DISSPATION: The Constant Voltage LED Driver is made of heat-resistant material and it also has overheating protection device inside. Easy for heat dissipation and ensure stability..
  • SAFER DESIGN: 120V to 12V Transformer is flicker-free output, thermal overload, over current, over voltage and short circuit protection built in. No noise isolation protection safety..
  • WIDE APPLICATION: 36W LED Driver can be applied to all kinds of LED devices, such as LED light strips, LED hard light strips, cabinet light, LED display, security camera, LED module, indoor LED deck light, puck light, rigid strip light, G4 bulb, MR11 bulb, MR16 bulb ect..
  • NOTE: Please confirm the input voltage (AC100-240V) can work in your place before purchase the 12V LED Switching Power Supply, and please make sure the power is not over 36W, otherwise it may burn..
Check Stock

HCDC RPi GPIO Status LED & Terminal Block Breakout Board HAT for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

  • The item has been soldered and assembled. Support for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B.
  • GPIO status LED and power 5V / 3.3V indication. GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs....
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion....
  • Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not....
Check Stock

EAGWELL Module Lights, 100 FT LED Window Lights Waterproof Storefront Light Business Decorative Lights 12V 5050 RGB LED Lights for Advertising Signs Business Store Light with SM-4P Connectors

  • 【Enough Brightness】3 LEDs for each module light, which ensure the brightness of your store, advertisements or any other attractive signs. There are 7 colors with the light: red, green, blue, purple, yellow,white, light blue. which can be switched between these 7 colors through the remote control. All Accessories are included (10 strands of LED Lights 100 feet long in total, 2 Power Plug, 2 Remote controller)..
  • 【Easy to Use】Easy installation With Super Sticky Self-Adhesive tape on the back of each module, you can stick or hang on anywhere you like.There are sm-4p connectors on the end of each strand of LED module light. It will be much easier for you to connect the lights. Just plug. No need to male female connectors any more. Please pay special attention to the positive and negative poles of the connectors to avoid short circuit..
  • 【Energy-saving】High energy efficient 5050 SMD module 30 watt and 200 Lumen for each, provides extreme energy saving solution and brightness for your business. The led window module light is powered by a 12V DC power supply and is driven by a constant current, which greatly reduces the fluctuating power efficiency, low powe....
Check Stock

Second Chance for Christmas: A Sweet Romantic Comedy Novella

  • 1 set of remote control RGB LED knight rider flashing light strip kit with 7 kinds of color and 130 distinct flash patterns, for car interior and exterior decoration..
  • 7 colors for option, Red (R), Green (G), Blue (B), Yellow (G+R), Magenta (R+B), Cyan (B+G), White (R+G+B)..
  • 130 Distinct flashing patterns.Flashing color and speed adjustable.
  • This LED scanner light bar can be commonly used on vehicles under hood, front grille, tailgate, trunk, cargo area, under spoiler, etc...
  • Package includes: 1x 48-SMD RGB type LED strip, 1x control module and 1x wireless remote control.
Check Stock