Categories

Best Pulley Shaft Key

AA Performance Products 88 x 69mm 1700cc Slip-in Piston & Cylinder Kit, Fits VW

  • [Shaft Sleeve Adapter Kit] This stainless steel shaft sleeve adapts a crankshaft for 5/8" x 3/4" x 3" diameter.It comes with 2.01" step key..
  • [ ] Made from stainless steel, precision machined and tumbled, high durability. It is durable in use, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage..
  • [Applications] Alters motors with a different diameter shaft. Alters pulleys for a different speed or belt. Reduces the necessity of buying a new motor or pulley to maintain existing components and speed/power requirements. Adapts larger wheel bores to smaller axles. Works with Gas Engine Crank Shafts to enlarge the crank diameter to fit pulleys, gear boxes etc..
  • Perfect Performance] Allows you to use your old clutch or pulley on a new engine, you may need to use a small hammer to gently tap it in to place for tightly fit..
  • [Package Include] 1 Set Shaft Sleeve Adapter Kit.
Check Stock

BEMONOC HTD3M 50 Teeth 25 Teeth Timing Belt Width 15mm Timing Pulley Belt Set kit Reduction Ratio 2:1

  • Aluminum Big Pulley: 50 Teeth, bore 14mm.
  • Aluminum Small Pulley: 25 Teeth, bore 6mm.
  • ✔If you need other pulleys and bore, pls contact us freely, there are many types of pulleys in our store..
  • 003cbr003eThe Package Listing Includes as Follow: 1pcs * 50 Teeth Timing Pulley + 1pcs * 25 Teeth Timing Pulley + 1pcs * 276mm Closed-loop Timing Belt + 4pcs x Setscrews + 2pcs x Allen Key.
Check Stock

X AUTOHAUX 1\ to 1 1/8 Inch -1/4\ Engine Shaft Sleeve Adapter Kit with Step Key for Car

  • [Shaft Sleeve Adapter Kit] This stainless steel shaft sleeve adapts a crankshaft from 1" to 1 1/ 8 inch -1/4" diameter. It comes with 2.05" step key..
  • [ ] Made from cold rolled stainless steel, precision machined and tumbled, high durability. It is durable in use, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage..
  • [Applications] Alters motors with a different diameter shaft. Alters pulleys for a different speed or belt. Reduces the necessity of buying a new motor or pulley to maintain existing components and speed/power requirements. Adapts larger wheel bores to smaller axles. Works with Gas Engine Crank Shafts to enlarge the crank diameter to fit pulleys, gear boxes etc..
  • Perfect Performance] Allows you to use your old clutch or pulley on a new engine, you may need to use a small hammer to gently tap it in to place for tightly fit..
  • [Package Include] 1 Set Shaft Sleeve Adapter Kit.
Check Stock

Bapmic Mechatronics Sealing Sleeve and Double D Gasket Compatible with BMW E60 E65 E66 E70 E71 E90 335i

  • [Shaft Sleeve Adapter Kit] This stainless steel shaft sleeve adapts a crankshaft from 3/4"to 7/8" inch diameter. It comes with 2.01" step key..
  • [ ] Made from stainless steel, precision machined and tumbled, high durability. It is durable in use, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage..
  • [Applications] Alters motors with a different diameter shaft. Alters pulleys for a different speed or belt. Reduces the necessity of buying a new motor or pulley to maintain existing components and speed/power requirements. Adapts larger wheel bores to smaller axles. Works with Gas Engine Crank Shafts to enlarge the crank diameter to fit pulleys, gear boxes etc..
  • Perfect Performance] Allows you to use your old clutch or pulley on a new engine, you may need to use a small hammer to gently tap it in to place for tightly fit..
  • [Package Include] 1 Set Shaft Sleeve Adapter Kit.
Check Stock

Crank Shaft Sleeve Adapter， 7/8" to 1" inch Gas Engine Pulley Crank Shaft Sleeve Adapter with Step Key Steel Silver 7/8 to 1 inch shaft adapter with clutch 7/8 centrifugal clutch crankshaft sleeve 7/8

  • ... of applications and can meet your various needs. Please confirm whether the product is Replacement before placing an order. for 7/7" to 25mm shaft adapter 7/8 centrifugal clutch.
  • PROFESSIONAL USE: The crankshaft sleeve adapter allows you to use the old clutch or pulley on the new engine, you may need to use a small hammer to gently tap it into place to make it Replacement tightly for 7/8 blade pulley crankshaft sleeve 7/8 to 1 in.
  • EASY TO INSTALL: Contains an adapter and keyway, the wider part of the key is located in the adapter. The installation is very simple and can be completed in a few minutes. It is your ideal accessory. for 7/8 to 1 inch shaft adapter 7/8 to 1 crankshaft adapter.
  • PARAMETER INTRODUCTION: The crankshaft sleeve adapter is about 3 inches long and includes the step key required from 1/4 keyway to 3/16 keyway. An adapter and keyway, the wider part of the key is located in the adapter, convenient and practical for briggs and stratton crankshaft adapter.
Check Stock

Martin SH 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.871\ OD, 1.31\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SDS 2 Quick Disconnect Bushing, Ductile Iron, Inch, 2\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 0.43\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SK 7/8 Quick Disconnect Bushing, Sintered Steel, Inch, 0.87\ Bore, 2.812\ OD, 1.93\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SDS 1 1/8 Quick Disconnect Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SF 1 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 1.44\ Bore, 3.125\ OD, 2.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SK 2 1/2 Quick Disconnect Bushing, Ductile Iron, Inch, 2.5\ Bore, 2.812\ OD, 1.93\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock