Categories

Best Relay Type Avr

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock

Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp

  • ★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
  • ★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
  • ★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
  • ★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
  • ★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..
Check Stock

Youngneer 5v Relay Board Raspberry Arduino Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
  • 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
  • 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
  • 【Wide Application】- These 5v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
  • 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check Stock

AEDIKO 4pcs Relay Module DC 5V Relay Switch 1 Channel Relay Board with Optocoupler Isolation Support High or Low Level Trigger

  • Fault-Tolerant Design: Fault Tolerant Design, Even if the Control Line is Broken, the Relay will not Operate.
  • All Interfaces of Relay can be Wired Out Through the Terminals Directly,Normally Open and Normally Closed.
  • Optocoupler Isolation:1 Channel Relay Board use Optocoupler Isolation that has Strong Driving Ability and Stable Performance ,The Isolation Circuit Prevent Damages to I / O Port by Relay Switch Current.
  • Jumper Design: The Relay Module has a Jumper That You Can Set Rather the Unit State Changes with High or Low Signal. Has Screw Terminals for Relay (NC,C,NO) and for Input.
  • Wide Application: DC 5V Relay Module Works Well with ARM /PIC /AVR /MCU/Raspberry/CNC Machine/ PS4 etc..
Check Stock

ELEGOO 8 Channel DC 5V Relay Module with Optocoupler Compatible with Arduino UNO R3 MEGA 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • 5V 8-Channel Relay interface board, each one needs 70mA Driver Current.
  • Equiped with high-current relay, AC250V 10A.
  • Each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • With power indicator,8-way road has a status indicator. With a relay coil to absorb the diode protection..
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
  • The 8 channels are optically isolated, safe, reliable, anti-interference. Widely used for all MCU control, industrial sector, PLC control, smart home control。For a complete data sheet for this relay board, please download it from: http://dwz.win/UhW.
Check Stock

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

  • This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
  • These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
  • Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
  • And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
  • Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Check Stock

WinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR

  • 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
  • Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
  • Standard interface can be directly connected with microcontrollers..
  • Red working status indicator for power on indication.Green working status indicator for relay the switch..
  • It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

3v Relay Board Raspberry Pi Arduino Relay Module 1 Channel Opto-Isolate High Level Trigger for IOT ESP8266 Microcontrollers Development Board

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Main Specification】- The 3v Relay 1 Channel power switch module compatible with 10A 250VAC and 10A 30VDC load.4pcs * 2.5 mm Fixed Bolt Hole..
  • 【Adopted Optocoupler Isolation】- 3V/3.3V power relay module supports photocoupler isolation control and dual power supply input ensure high anti-interference ability. Fast response time less than 20ms and long life time up to 100,000 times snap action with diode freewheel protection..
  • 【Jumper Caps】You can select whether the relay and the signal use the same power supply or not by removing the jumper caps on the pins. And It is better to share the same power supply, because that is more convenient for using..
  • 【Wide Application】- These 3v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/IOT/ ESP8266 module etc..
Check Stock

ALMOCN 6Pcs DC 5V 1 Channel Relay Module With Optocoupler Isolation Support High or Low Level Trigger

  • The Relay Board Maximum load: AC 250V/10A, DC 30V/10A.
  • Using SMD optocoupler isolation, strong driving capability, stable performance..
  • Can be set high or low level trigger with jumper cap, to meet the demand of more trigger applications..
  • Fault-tolerant design, even if the control line is broken, the relay will not move..
  • Wide Application,The relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
Check Stock

Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10

  • 【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
  • 【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
  • 【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
  • 【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • 【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
Check Stock

AOICRIE 12V 16-Channel Relay Interface Board Module Optocoupler LED LM2576 Power for Arduino DIY Kit PiC ARM AVR

  • ★12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • ★Equipped with high-current relay, AC250V 10A.
  • ★The control signal voltage range: the trigger signal is low 0-2V.
  • ★Standard interface that can be controlled directly by microcontroller (for Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • ★DC 12V 16 Channel Relay Module Interface Board With Optocoupler Protection LM2576 Power for Arduino DIY Kit.
Check Stock

Xiuxin 2pcs 5V 8 Channel Relay Module Board for Arduino PIC AVR DSP ARM

  • 2pcs/lot 8 Channel relay module board, Working voltage: 5V.
  • This board is for Arduino PIC AVR DSP ARM.
  • Support all single-chip microcomputer control,Industrial circle,PLC controller,Household intelligent control.
  • Relay output maximum contact is AC250V 10A and DC30V 10A.
  • Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock