Categories

Best Rf Signal Analyzers

YWBL-WH Logarithmic Power Detector Meter AD8317 1M-10GHz 60dB RF Power Meter Logarithmic Detector Controller for Amplifier 50 Ohms

  • AD8317 CHIP---The logarithmic power detector is designed by using AD8317 chip, and is used for RF signal power detection.
  • -55dBm to 0dBm---The logarithmic power detector can detect power in -55dBm to 0dBm of an RF signal, so that the RF signal is converted to DC voltage output.
  • APPLICATION AREAS---The logarithmic power detector could be used for RF transmitter PA set point control and level monitoring.
  • Power monitoring in a radio line transmitter.
  • RSSI measurements in base stations, WLAN, WiMAX, and radar.
  • 55dB---The greater the amplitude or power of the RF signal, the higher the output voltage, and the output voltage is directly proportional to the logarithm of the input signal amplitude, thus expanding the dynamic range of the detected signal, which ranges reach 55dB.
  • WIDE APPLICATION---The logarithmic power detector could be widely used radio frequency signal detection, signal power measurement, environmental field strength detection, or as a part of automatic gain control and automatic level control.
Check Stock

Bindpo RF Logarithmic Detector, 1M-10000MHz AD8317 Radio Frequency Logarithmic Detector Power Meter, for RF Signal Power Detection/Radio Frequency Signal Detection

  • The product is designed by using AD8317 chip, and is used for RF signal power detection..
  • Can detect power in -55dBm to -0dBm of an RF signal, so that the RF signal is converted to DC voltage output..
  • The greater the amplitude or power of the RF signal, the higher the output voltage, and the output voltage is directly proportional to the logarithm of the input signal amplitude, thus expanding the dynamic range of the detected signal, which ranges reach 55dB..
  • It can be widely used in radio frequency signal detection, signal power measurement, environmental field strength detection..
  • It can also be used as part of automatic gain control and automatic level control..
Check Stock

Portable TinySA Spectrum Analyzer, SEESII Upgraded V0.3.1 Tiny Frequency Analyzer with Antenna SMA Male to UHF Female Cables, 100kHz to 960MHz MF/HF/VHF UHF Input, 2.8'' Touchscreen Signal Generator

  • ...-in Calibration Signal Generator】When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration..
  • 【Tiny Spectrum analyzers】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range. Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use..
  • 【PC Control】Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer.The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel..
  • 【Package List】1x Tiny Spectrum Analyzer.
  • 1 x SMA Telescopic Antenna.It's very useful as an antenna analyzer for your ....
Check Stock

HDMI to RF Coaxial Converter Box, 1080P Video Adapter Support Input HDMI Resolution: 480I/480P/576I/576P/720P/720I/1080I/1080P(US Plug)

  • 【HDMI to RF Converter】The RF converter can easily help you convert HDMI signal to RF signal, easy to use. HDMI to Coaxial Cable Adapter for TV. With the remote control, you can adjust the output screen and amplitude including brightness, contrast, and chroma..
  • 【HDMI Source Devices to Your Old TVs】Display DVD/game/set top box (HAMI signal source device) on normal or old TV, long distance signal transmission via coaxial cable. The converter outputs an analog signal instead of ATSC format..
  • 【How to Use it】The output TV/RF signal frequency is 61.25MHZ. Please use the search channel function of the TV to get the signal, then press "SYS" to adjust the format (PAL or NTSC) and correspond to the TV until you get clear picture and sound..
  • 【Note】The output image quality will be lower than the RF analog signal (more like 480p). This device cannot work in reverse. Support input HDMI resolution:480I/480P/576I/576P/720P/720I/1080I/1080P..
  • 【After Sales Service】If there are any using problems or unsatisfactory with our products, please feel free to contact us, our professional customer service team will consult the issues with sincerity. Thanks for purchasing from us..
Check Stock

4 Pack 3DHeaven Rechargeable 3D Glasses Compatible with EPSON ELPGS03 3-D Glasses

  • [RF 3D Glasses] The active shutter 3D glasses use RF to transmit signals, works without emitter. Compared with traditional IR signal transmission, the RF signal connection is faster, and the continuity is more stable. Pack of 2, super saving!.
  • [Compatible Devices] The RF 3D active shutter glasses suitable for most of RF 3D signal TVs and 3D projectors. Compatible 3D RF projector: EPSON, Sony, JVC, xiaomi2, Lenovo and other more.
  • Compatible 3D HD TVs: Epson, Samsung, Sony, Panasonic, Sharp, Toshiba, Konka, TCL, Haier and more. Can replace these models of 3D glasses: TDG-BT500A, TDG-BT400A, SSG-5100GB, TY-ER3D4MU, AN3DG40 and more. [PLEASE NOTE: Device before 2012 is not compatible with this remote control.].
  • [Easy to Use] Rechargeable design 3d RF glasses, with ON/OFF switch. Auto 5 seconds Stand by and 5 minutes Shut Off. Not throwaway 3D glasses. High definition, no ghosting images, no flickering, clearer and more stable than IR signal connection. Providing you a superior 3D visual experience!.
  • [Quickly Pairing] When pairing, please make sure that the distance between the 3D glasses and the 3D device is less than 19.5 inches/50 cm. Press the switch button, the green LED indicator will stay on for 3 seconds, the glasses are in the power-on state, then s....
Check Stock

AD8317 Logarithmic Detector, RF Log Detector Logarithmic Detector, Logarithmic Detector RF Signal Log Output Power Meter 1M-10000MHz Controller

  • [Main function]: This logarithmic detector is designed for ADI's AD8317 chip and is used for RF signal power detection..
  • [Detection frequency range]: The detection frequency range of the logarithmic detector is 1M-10GHz, and it can detect RF signals with a power of -55dBm to -0dBm, and convert the RF signal into a DC voltage output..
  • [Excellent performance]: The greater the RF signal amplitude or power, the higher the output voltage, and the output voltage is proportional to the logarithm of the input signal amplitude, which will expand the dynamic range of the detected signal by 55dB..
  • [Wide use]: The logarithmic detector is widely used in radio frequency signal detection, signal power measurement, environmental field strength detection, and can also be used as a component of automatic gain control and automatic level control..
  • [Stable and durable]: This logarithmic detector can withstand high and low temperatures, is stable and durable, with a temperature measurement range of 0°C to 1024°C, and a converter temperature resolution of 0.25°C..
Check Stock

Professional RF Cable TV Signal Amplifier with High 40dB Gain

  • Professional-grade cable TV and antenna signal amplifier with high 40dB output level. Supports TV coax cable signal from cable outlet, cable TV box, antenna, DTV, CCTV DVR, MATV or all other RF modulated TV system. Designed for large multi-dwelling units(MDU) that require precise RF amplification with gain and slope adjustments for a professional installation..
  • High-power amplification to compensate for the attenuations of the passive TV distribution components like cable, taps, splitters and cable outlets. Advanced CATV hybrid circuitry providing extremely low-noise figure and minimum distortion. Adjustable gain control and tilt control allows for easy system balancing..
  • Solution in solving the problems of noise, interference and weakness after distribution. Boost RF coax signal with ease for more than 1700FT or 500m if RF TV source signal has fair 70/75dB strength to start with. Boosts the existing CATV or antenna signal strength for greater distance with minimum loss for more TV distribution..
  • Adjustable gain/attenuation to reduce overdriving. Adjustable tilt compensation to allow large CATV systems to be properly balanced and mixed with other CATV or existing RF distribution system. Supports full TV frequency range from 40MHz to 860MHz for analog/di....
Check Stock

Shure PA411 Four Port Antenna Combiner

  • Distributes DC power and RF signal while reducing rack clutter for up to four PSM300 systems.
  • Features a wideband 470-865 MHz frequency range.
  • Main RF output connector connects to any antenna with a BNC connector.
  • RF LED indicators display signal present and signal overload per input.
  • Power output distributes DC power to PSM transmitters (accessory power cable required).
  • Includes PA411, rack mount and hardware kits, 1/4 wave antenna, BNC bulkhead adapter, BNC cable, power supply, power splitter cable, and user guide.
Check Stock

Richer-R HDMI to Coax RF Converter Modulator for TV, HDMI to RF Coaxial Converter Adapter Box with Remote Control, Support 480I/480P/576I/576P/720P/720I/1080I/1080P (100-240V)(US)

  • 【Converter】The RF converter can easily help you convert HDMI signal to RF signal, easy to use.The converter outputs an analog signal instead of ATSC format.Display DVD/game/set-top box (HAMI signal source device) on normal or old TV, long-distance signal transmission via coaxial cable..
  • 【Input HDMI Resolution】The output TV/RF signal frequency is 61.25MHZ. Please use the search channel function of the TV to get the signal, then press "SYS" to adjust the format (PAL or NTSC) and correspond to the TV until you get clear picture and sound..
  • 【Output Image Quality 】The Quality will be lower than the RF analog signal (more like 480p). With the remote control, you can adjust the output screen and amplitude including brightness, contrast, and chroma..
  • 【Input HDMI Resolution】Support : 480I/480P/576I/576P/720P/720I/1080I/1080P.This device cannot work in reverse..
  • 【Tip】Any questions,Please feel free contact us,we will provide you with high quality after-sales service..
Check Stock

DLP LINK 144 Hz Ultra-Clear HD 2 PACK 3D Active Rechargeable Shutter Glasses for All 3D DLP Projectors - BenQ, Optoma, Dell, Mitsubishi, Samsung, Acer, Vivitek, NEC, Sharp, ViewSonic & Endless Others!

  • [RF 3D Glasses] The active shutter 3D glasses use RF to transmit signals, works without emitter. Compared with traditional IR signal transmission, the RF signal connection is faster, and the continuity is more stable. Pack of 2, super saving!.
  • [Compatible Devices] The RF 3D active shutter glasses suitable for most of RF 3D signal TVs and 3D projectors. Compatible 3D RF projector: EPSON, Sony, JVC, xiaomi2, Lenovo and other more.
  • Compatible 3D HD TVs: Epson, Samsung, Sony, Panasonic, Sharp, Toshiba, Konka, TCL, Haier and more. Can replace these models of 3D glasses: TDG-BT500A, TDG-BT400A, SSG-5100GB, TY-ER3D4MU, AN3DG40 and more. [PLEASE NOTE: Device before 2012 is not compatible with this remote control.].
  • [Easy to Use] Rechargeable design 3d RF glasses, with ON/OFF switch. Auto 5 seconds Stand by and 5 minutes Shut Off. Not throwaway 3D glasses. High definition, no ghosting images, no flickering, clearer and more stable than IR signal connection. Providing you a superior 3D visual experience!.
  • [Quickly Pairing] When pairing, please make sure that the distance between the 3D glasses and the 3D device is less than 19.5 inches/50 cm. Press the switch button, the green LED indicator will stay on for 3 seconds, the glasses are in the power-on state, then s....
Check Stock

Portable TinySA Spectrum Analyzer,SEESII Upgraded V0.3.1 Handheld Tiny Frequency Analyzer 100kHz to 960MHz MF/HF/VHF UHF Input,Signal Generator with 2.8 inch Touch Screen with ESD Protect Function

  • ...-in Calibration Signal Generator】When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration..
  • 【Tiny Spectrum analyzers & ESD Function】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range. Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use.The performance of the 2021 latest version 3.1 will be more stable and sensitive, with a new ESD protrcted function enable the product to have a higher antistatic level and a longer service life..
  • 【PC Control】Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer.The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel..
Check Stock

HDMI to RF Conversion Box,HDMI to RF Coaxial Converter Adapter,Output TV/RF Signal Frequency is 61.25MHZ,Long-Distance Signal Transmission,Remote Control to Adjust Output Data

  • REMOTE TRANSMISSION: View DVD / games / set-top box (Hami signal source devices) on regular or old TV and remote signaling is not possible over coaxial cables. The converter outputs analog signals instead of the ATSC format..
  • OUTPUT FREQUENCY: The output frequency of the TV / RF signal is 61.25 MHz. Please use the TV's channel search function to get the signal, then press "SYS" to set the system (PAL or NTSC) to match the TV until you get a clear picture and sound..
  • SUPPORT RESOLUTION: The RF converter can easily help you convert the HDMI signal to the RF signal, easy to use. This device cannot work backwards. Supported HDMI input resolution: 480I / 480P / 576I / 576P / 720P / 720I / 1080I / 1080P..
  • ADJUST THE DATA: The output image quality is lower than that of the analog RF signal (more like 480p). Use the remote control to adjust the output image and amplitude including brightness, contrast and chroma..
  • NOTES AND CUSTOMER SERVICE: If you have any questions or dissatisfaction with our products, please feel free to contact us, we will advise sincerely..
Check Stock

Wifi Signal Strength Meter

  • Detects all three types of EMF pollution: AC magnetic, AC electric, and RF/microwave.
  • Displays signal level, peak level, and a fast indicator bar (for pulse monitoring).
  • AC magnetic, AC electric, RF/Microwave (measures total RF signal but NOT frequency).
  • AC fields: can measure standard measurements or weighted (proportional to current induced in the human body).
Check Stock