Categories

Best Round Die Tap Set

BSP BRITISH STANDARD PIPE BSPP PARALLEL TAP AND DIE SET - 8 SIZE 1/8 TO 1

  • BSP/BSPP (British Standard Pipe) Tap and Die Set - 24 Piece.
  • 1 taper tap, 1 bottom tap and 1 die in each size below:.
  • Taps are 1/8" - 28, 1/4" - 19, 3/8" -19, 1/2" -14, 5/8" - 14, 3/4" - 14, 7/8" - 14, 1" - 11 TPI.
  • Dies are 1", 1-1/2" and 2" OD Round Dies..
Check Stock

WASTOREEL 12mm x 1.25 HSS Metric Right Hand Thread Tap and Die Set M12 x 1.25mm Pitch

  • MODEL: M12 x 1.25 Metric Tap and Die set, Material: HSS.
  • ROUND THREAD DIE: Not easily broken tooth chip fast, abrasion resistance and long service life..
  • THREAD TAP: debris rapidly discharged in the tank. No blocking, fast efficiency and high efficiency..
  • CHARACTERISTICS: Heat treated and tempered for file hard threads and a long, useful life..
  • PACKAGE INCLUDES: 2pc M12 x 1.25 Metric TAP & 1pc M12 x 1.25 Metric DIE.
Check Stock

uxcell Tap and Die and Drill Bit Set M14 x 2 Left Hand Thread Milling Tap and Round Die 12mm Cobalt High Speed Steel Twist Drill Bit

  • Compatibility: M14 x 2 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
  • Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
  • Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
  • 12mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
  • Tips: Recommended feed rate: general steel: 6-15m/min.
  • cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Check Stock

uxcell Tap and Die and Drill Bit Set M12 x 1.75 Left Hand Thread Milling Tap and Round Die 10.2mm Cobalt High Speed Steel Twist Drill Bit

  • Compatibility: M12 x 1.75 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
  • Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
  • Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
  • 10.2mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
  • Tips: Recommended feed rate: general steel: 6-15m/min.
  • cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Check Stock

Neiko 00916A 45 Piece SAE Tap & Die Set, SAE Tap and Die Set, Tap Set, Rethreading Kit, Pro-Grade Large Tap and Die Set, Titanium Threading Tools, Thread Chaser Set, Tap & Die Set Standard

  • HEAVY DUTY TAP & DIE SET: Titanium cutting edges hold sharpness up to 20x longer than steel, making this a perfect SAE tap and die set for any project, big or small..
  • VERSITILE: Create new threads or repair damaged threads on most metals like carbon steel, cast iron, aluminum, brass, copper, and stainless steel with this tap and die kit..
  • DURABLE STORAGE CASE: This large tap and die set standard is fully equipped in a heavy-duty molded case for easy identification, storage, and portability for all your jobs on the go..
  • PREMIUM MATERIAL: Our SAE thread chaser set is made of a professional grade steel, highly durable and built to last for multiple uses. This tap set is perfect car repairs, DIY projects, and much more..
  • COMPLETE SET INCLUDE: This rethreading kit comes with the most popular SAE taps & dies. T-handle tap wrenches, adjustable die wrench, screwdriver, and thread pitch gauge..
Check Stock

Toolly 32pcs Tap and Die Set, Metric Hardened Steel Tool Set, Essential Threading & Rethreading Tool with Storage Case Perfect for Auto and Machinery Repair

  • 【32pcs Tap and Die Set】The package includes 28pcs (each size including 1x taper tap, 1x second tap, 1x plug tap and 1x die): M3 X 0.5, M4 X 0.7, M5 X 0.8, M6 X 1.0, M8 X 1.25, M10 X 1.5, M12 X 1.75.
  • 1 x Tap Wrench, 1 x Die Stock Wrench, 1 x Thread Pitch Guage, 1 x Screwdriver, to cover all your needs..
  • 【Product Function】Tap and die set in metric is perfect for rethreading fasteners, fastener holes for auto and machinery repair. Threading tool with storage case, can greatly increase your productivity and act as an important part to your work..
  • 【Tapered Teeth Design & Versatility】Taps (for internal threads) and Dies (for external threads) feature with tapered teeth that start threading more easily. Perfect for creating new threads or repair damaged threads on most metals like carbon steel, cast iron, aluminum, brass, copper and stainless steel..
  • 【High Quality & Durable】Tap and die set adopts premium hardened steel material. The screw thread tapping tool is durable to use. The better the material the tougher the tap and die so they ensures durability and tool longevity to withstand professional uses..
  • 【SIZE LABLED】All of them are clearly labled with size for you to find quickly, and be able to pull the right size out of the box when you ....
Check Stock

Muzerdo 115PCS Sae and Metric Bearing Steel Tap and Die Rethreading Kit with Metal Box

  • Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more.
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of course then you don’t have t.
Check Stock

Muzerdo 110PCS Standard Sae and Metric Bearing Steel Tap and Die Rethreading Kit

  • CUT & RENEW THREADS: The ABN | Metric Tap and Dies Set 110-Piece Metal Threading Kit cuts and renews external and internal threads to exact standards.
  • Ideal for professional machinists and DIY weekend warriors alike to rethread existing auto and machinery fasteners, remove screws/bolts, cut raw material.
  • Tap wrench fits the different sizes of taps, thread taps are used to process internal thread, thread die set is for external thread, plug taps suitable for cleaning and rethreading.
  • FITS YOUR APPLICATION: Metric – Taper taps (2x0.4, 3x0.5, 4x0.7, 5x0.8, 6x7.5, 6x1, 7x0.75, 7x1, 8x0.75, 8x1, 8x1.25, 9x0.75, 9x1, 9x1.25, 10x0.75, 10x1, 10x1.25, 10x1.5, 11x0.75, 11x1, 11x1.25, 11x1.5, 12x0.75, 12x1, 12x1.25, 12x1.5, 12x1.75, 14x1, 14x1.25, 14x1.5, 14x2, 16x1, 16x1.5, 16x2, 18x1.5,).
  • Tap wrenches (M3-M12 x 1/16”-1/2”, M6-M20 x 1/4”-3/4”).
  • Die wrenches (25mm x 1”, 38mm x 1-1/2” OD).
  • BUILT TO LAST: Constructed from chromium-coated high carbon steel for maximum strength and corrosion resistance.
  • Metric tap set has 3-4 flute abrasive cutting edges each so you can easily clean/repair and cut materials such as aluminum, iron, cast iron, alloy steel, carb....
Check Stock

ATOPLEE Spiral Point Plug Threading Tap ,5pcs HSS 6542 Titanium Coated Metric Right Hand Thread Taps,M3-M8

  • Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more materials and they will stay sharper for longer..
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of cour....
Check Stock

3/4-20 HSS Tap And Die Set， UNEF Machine Thread Tap And UNEF Round Thread Die Right Hand

  • Size : 3/4"-20 thread tap and thread round die , Pitch:20 , Material : HSS..
  • Tap : Chip removal, high efficiency, debris rapidly discharged in the tank. No blocking, fast efficiency..
  • Round Die: Not easily broken tooth chip fast, abrasion resistance and long service life..
  • HSS tap offers precision cut threads, accurately formed for consistent, exact threading..
  • Advantage : Heat treated and tempered for file hard threads and a long, useful life..
Check Stock

45 Pc Tap & Die Set Metric Mm Titanium Tungsten Steel Jumbo Thread Renew Tool

  • 86 Piece Tap and Die Set Bearing Steel Sae and Metric Tools, Titanium Coated with Metal Carrying Case.
  • Size:14.8 x 10.7 x 2.2"inch / 37.6 x 27 x 5.6cm. Weight:12lb / 5.4kg. Material upgrading:Alloy Steel 55¡ã- 60¡ã, Sizes Stamped Engraved-etched On the Metal.
  • SAE TAP SIZES and SAE DIE SIZES: 1/8"-27NPT, 4-40, 6-32, 8-32, 10-32, 10-24, 12-24, 1/4"-20, 1/4"-28, 5/16"-18, 5/16-24, 3/8"-16,3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18.
  • METRIC TAP SIZES and METRIC DIE SIZES: M3-0.5, M4-0.7, M5-0.8, M6-1.0, M7-1.0, M8-1.0, M8-1.25, M9-1.25, M10-1.5, M10-1.25, M11-1.5, M11-1.25, M12-1.75, M12-1.5, M14-2, M14-1.5, M16-2, M16-1.5.
  • Ideal for rethreading fasteners and fastener holes for auto and machinery repair. Perfect set for the professional craftsman Tap and die set is designed to thread cutting: tap is used to process internal thread, while the die is for external thread.
  • Easy Storage: Heavy-duty plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
Check Stock

86-Piece Tap and Die Set Combination Tap Die Set Metric Tungstem Steel Titanium SAE Standard for Cutting

  • Tap Material: High Speed Steel, Die Material: Alloy Tool Steel..
  • Application: Process Steel, Iron, Aluminum, Copper and other metals, widely used in thread repair and other processing..
  • Package Include: 1 x 1/2"-28 UNEF Tap & 1 x 1/2"-28 UNEF Round Die..
Check Stock

Lathe Tailstock Sliding Tap Die Holder MT2 Shank - Tapping Threading Reaming Drilling - 2MT

  • Lathe Tailstock Sliding Tap Die Holder MT2 Shank - Tapping Threading Reaming Drilling - 2MT.
  • ​​​A Tail Stock Tap Die Holder Should Be Among The First Accessories a Machinist Makes For His Lathe, Since Threading With A Hand Held Die Stock....
  • 3 Die Holders Are Interchangeable & Can Hold Die Sizes of 13/16" + 1" + 1-1/2"..
  • 3 Tap Holders Are Interchangeable & Can Hold Taps 0" to 1/4" + 1/4" to 1/2" + 1/2" to 3/4".
  • EXCLUSIVE - TAP AND DIE HOLDER SET - OTHER SIZE MT1 AND MT3 IN OUR SHOP !.
Check Stock