Categories

Best Serial To Ethernet Module Board Adapter

Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino

  • Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
  • Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
  • The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
  • There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
  • Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
Check Stock

SainSmart USB 4 Channel Relay Automation (5V)

  • NOYITO 2-Channel Micro USB Relay Module is equipped with a stable USB to serial port chip and a microcontroller. It can use the serial port debugging software to send serial commands on the computer to control the opening and closing of the 2-channel relay..
  • Onboard high performance microcontroller chip, CH340 USB control chip.With power LED indicator and relay status LED.On-board 2-channel 5V, 10A/250VAC, 10A/30VDC relay, long relay life, can work 100,000 times continuously..
  • Module with overcurrent protection and relay diode freewheel protection..
  • NOYITO 8-Channel Micro USB Relay Module ASIN：B09RGTSHHW.
  • NOYITO 4-Channel Micro USB Relay Module ASIN：B09RGVQXXT.
Check Stock

Intel Server System SR1530HCLSRNA

  • 1u Rm Sr1530hcls Dp 3x Hs Sas 45nm 400wType Server Form Factor Rack-mountable - 1U Approximate Dimensions (WxDxH) 16.9 in x 20 in x 1.7 in Localization North America.
  • Server Scalability 2-way Processor No CPU RAM 0 MB (installed) / 12 GB (max) - DDR II SDRAM - ECC Storage Controller Serial Attached SCSI ( Serial Attached SCSI ).
  • IDE Server Storage Bays Hot-swap 3.5" Hard Drive None..
  • Monitor None. Graphics Controller ATI ES1000 - 16 MB Networking Network adapter - Ethernet, Fast Ethernet, Gigabit Ethernet - Ethernet Ports : 2 x Gigabit Ethernet.
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

CP2102 6 in 1 USB to TTL Serial Adapter Module USB to TTL 485 232,TTL to 232 485,RS232 to 485 + 4P Dupont Cable Jumper Wire Female to Female for Nextion Display Beitian GPS Arduino Windows

  • -cp2102 serial adapter module supports usb to ttl, usb to rs232, usb to rs485, ttl to 232, ttl to 485, 232 to 485..
  • -USB specification 2.0 not 3.0, compatible with arduino,Windows XP/7/8/10 32bits/ 64bits, Linux etc..
  • -You need to set the dip switches for different conversion purpose..
  • -Before make 6 in 1 usb to ttl module work, you need to install cp2102 driver..
  • -cp2102 usb to ttl adapter widely used with nextion display, beitian gps, esp-01s adapter, sim7000a board etc..
Check Stock

waveshare Original Raspberry Pi Compute Module 4 IO Board for All Variants of Compute Module 4,with Real-Time Clock Dual MIPI DSI/CSI Interfaces,USB Connectors

  • The Compute Module 4 IO Board is a companion board for all variants of Raspberry Pi Compute Module 4(supplied separately). It is designed for use both as a development system for Compute Module 4 and as an embedded board integrated into end products..
  • The Compute Module 4 IO Board is designed to allow you to create systems quickly using off-theshelf parts such as HATs and PCIe cards, which might include NVMe, SATA, networking, or USB. The major user connectors are located along one side to make enclosures simple..
  • Connectors: Standard Raspberry Pi HAT connectors with PoE support. Standard PCIe Gen 2 x1 socket. Various jumpers to disable specific features, e.g. wireless connectivity, EEPROM writing..
  • RTC : Real-time clock with battery socket and ability to wake Compute Module 4 Video: 2 x MIPI DSI display FPC connectors (22-pin 0.5 mm pitch cable) Camera: 2 x MIPI CSI-2 camera FPC connectors (22-pin 0.5 mm pitch cable).
  • USB: 2 x USB 2.0 connectors. Micro USB socket for updating Compute Module 4. Ethernet: Gigabit Ethernet RJ45 with PoE support..
Check Stock

Geekworm KVM-A3 Kit with Raspberry Pi 4 Case Compatible with PiKVM ATX HDMI CSI for Raspberry Pi 4 Model B Only(Not Include Raspberry Pi)

  • 【What is it】This kit allows user to realize a PiKVM / KVM project with raspberry pi 4 which can control a computer using a web browser!.
  • 【Compatiblity】for use with Raspberry Pi 4 Model B 8GB / 4GB / 2GB / 1GB only, the metal case only support Raspberry Pi 4..
  • 【Function】Remotely turn on/ turn off / restart your computer.
  • reinstall the OS using the Virtual CD-ROM or Flash Drive.
  • Simulate a keyboard, mouse, and a monitor and presented in a web browser, etc..
  • 【How to Power】Power Input: 5.1Vdc +/-5% , ≥3A.
  • Power Via USB Type-C port of X630-A3. (DON'T power via Raspberry Pi's TYPE-C port, because it is occupied as USB OTG.) Recommend to use Geekworm UL listed 20W 5V 4A USB Type-C power adapter (ASIN:B09J856PND)..
  • 【Cooling Solution】X630-A3 with a on-board 3007 cooling fan for heat dissaption of Pi4.
  • 【What Included】1 x KWM-A3 Metal Case with Accessories, 1 x X630-A3 V1.2 Expansion Board with Accessories, 1 x X630-A5 V1.0 Adapter Board with Accessories, 1 x X630 HDMI to CSI-2 Module with Accessories, 1 x Ethernet Cable(1m length), 1 x0.96 inch OLED Module.
  • 【Extra Needed】Raspberry Pi 4, TF Card, HDMI Cable, Power Adapter.
Check Stock

Aoicrie 16x2 2004 LCD Display Module with IIC/I2C/TWI Serial Interface Adapter, IIC I2C TWI 1602 Serial LCD Module Display, for Mega 2560

  • IIC I2C TWI 1602 Serial LCD Module Display for R3 Mega 2560 16x2..
  • Easy to use. Less I/O ports are occupied, only four - VCC, GND, SDA (serial data line), SCL (serial clock line)..
  • Support IIC protocol. The I2C LCD1602 library is provided, so you can call it directly..
  • With a potentiometer used to adjust backlight and contrast.Power supply: +5V, Address of the module: ox27..
  • Widely Applications: LCD display module based on the popular HD44780 controller, works great with for Mega2560 board and other micro-controllers..
Check Stock

Chase Research IOLAN DS1 1-Port Device Server (04030124)

  • Nonstandard baudrates supported with high precision.
  • Port buffers for storing serial data when the Ethernet is offline.
  • Supports IPv6 / Ethernet redundancy (STP/RSTP/Turbo Ring) with network module.
  • Modular design for scalability / DES/3DES/AES for highly secure data transmissions.
Check Stock

HiLetgo 1602 LCD Keypad Shield 1602 LCD Expansion Shield Board Blue Backlight 4.5-5.5V for Arduino Duemilanove Robot

  • ☆ Premium Quality: Made of premium material, this lcd module display is sturdy, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage.
  • ☆ TFT LCD Serial Port Module : The lcd display module is a new 2.8 inch serial SPI color display module. Designed with one socket for sd card and PCB adapter for LCD.
  • ☆ Come With PCB Plate: With PCB plate (including power supply IC, SD), pcb display module is compatible with 5110 interface. Resolution: 128x160.
  • ☆ Support Analog & Hardware SPI: This tft display module supports analog SPI and hardware SPI, less I/O port need. It can be driven by 8051 / AVR / PIC /ARM/STM32. It can be driven with at least four IO.
  • ☆ What You Will Get: If you need the document to download, please contact us. We stand behind all of our them with a 100% product guarantee and promise to give you the best in customer care.
Check Stock

Geekworm KVM-A4 Kit Compatible with PiKVM HDMI CSI for Raspberry Pi Zero 2W/Zero W Only(Not Include Raspberry Pi)

  • ...sink for heat dissipation of Raspberry Pi Zero 2 W. C296 also compatible with Raspberry Pi Zero W by using thermal pads of different thicknesses..
  • 【What Included】1 x X630-A4 V1.1 Expansion Board with Accessories, 1 x X630-A5 V1.0 Adapter Board with Accessories, 1 x X630 HDMI to CSI-2 Module with Accessories, 1 x Ethernet Cable(1m length), 1 x0.96 inch OLED Module.
  • 【Extra Needed】Raspberry Pi Zero 2W/Zero W, TF Card, HDMI Cable, Power Adapter.
Check Stock

2Pcs NRF24L01+PA+LNA RF Wireless Transceiver Module with SMA Antenna 2.4G 1100m & Wireless Module with Breakout Adapter On-Board 3.3V Regulator

  • NRF24L01+PA+LNA Wireless Transceiver Module is a 2.4GHz ISM band transceiver, compatible with Raspberry Pi. Auto-acknowledge and auto-retransmit abilities.
  • Support up to six channels of data reception.
  • the transceiver come with power amplifier and SMA antenna, which make the effective communication distance has been greatly expanded..
  • A host microcontroller can communicate and configure the nRF24L01+ over a 4-pin Serial Peripheral Interface (SPI). The configuration registers are accessible through the SPI connection. Configurable parameters include frequency channel (125 selectable channels), output power, and data rate (data rates: 250kbps, 1Mbps, and 2Mbps)..
  • RF24L01+ Breakout Adapter: Small power on SMD LED indicator, On-board 3.3V voltage regulator, which accepts +5V power supply input and provides 3.3V for the attached "nRF24L01+" module..
  • Applications:It can be wildly used in wireless remote control such as RC planes/vehicles, wireless audio, wireless voice transmission such as VoIP, wireless networks, smart home,somatosensory devices, RFID, NFC etc..
  • Package Included:2 x NRF24L01+PA+LNA Wireless Transceiver Module+2 x SMA Antenna+2 x NRF24L01+ Breakout Adapter.
Check Stock

AITRIP 3PCS 2004 20x4 LCD Module IIC I2C Interface Adapter Blue Backlight Compatible with Arduino R3 Raspberry MEGA2560 (Blue)

  • LCD display module based on the popular HD44780 controller, works great with for Arduino / for Mega2560 board and other micro-controllers..
  • It only takes two I/O port thus saving more for other usages. You can adjust the contrast by the potentiometer at its back. If you don’t want the back light, you can also unplug the jumper cap at the LCD back..
  • No need to buy the adapter extra, this kit contains a IIC/I2C/TWI Serial Interface Adapter, with witch you can start your project at any time..
  • With this shield, you can display whatever you want by programming the for Arduino board. Therefore, this is a perfect choice to make your project more interesting and vivid! Totally display 20 characters in one row, 4 rows can display 80 characters..
Check Stock