Categories

Best Servo Extender Board

15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

  • You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
  • Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
  • Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
  • Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
  • Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.
Check Stock

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

  • Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
  • Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
  • 2.You should connect higher power supply for higher-power servo.
  • 3.Make sure servo are connected properly, otherwise they will not move..
  • Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
  • Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..
Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

  • 10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
  • Great for jumping from board to board or just about anything else..
  • There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
  • Length:100mm Type:JR Plug Servo Extension wire (Male to Male).
Check Stock

6Pcs ShareGoo JR Style Servo Splitter Cable, 2.75' Servo 1 Male to 2 Female JR Y Harness Y Cable Extension Wire for RC Models Car Airplane Helicopter Drone Boat

  • Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
  • This servo Y-cable allows you to control two servos with one radio channel..
  • Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
  • 3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
  • Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..
Check Stock

Arduino Uno 3 Ultimate Starter Kit Includes 12 Circuit Learning Guide

  • This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
  • Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
  • Includes a total of over 190 electronic parts and components.
Check Stock

sb components Motor Driver Board for The BBC Micro bit 2 Channel DC Motors and 3 Channel Servos Motors Motor Driver for Micro bit BBC microbit Motor Driver Board

  • micro:bit edge connector, directly pluggable.
  • 2x DC motor interfaces, 3x servo interfaces.
  • Integrates 5V regulator, up to 3A output current.
  • Onboard multi connector options for DC motors in different specifications, onboard standard servo headers.
Check Stock

KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino

  • This expansion board can directly stack on the controller R3 board and can drive up to 16 servos.
  • Uses I2C input, just occupy A4 and A5 interface on the control board.
  • Contains PCB double sided holes, can direct to solder with components to build up prototyping circuits.
  • Servo power supply independent V + input up to 6V.
  • How to use: Search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product..
Check Stock

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

  • MKS servo42C is a product developed by MKS to meet market demand. The closed-loop motor uses the motor's rotation angle feedback to the drive circuit to detect whether every step that should be taken has been taken to prevent losing steps. If a closed loop occurs, the motor will make up or lose steps through the feedback information, and the blue LED on the closed loop module will light up..
  • Support 1-256 subdivision,odd subdivision (such as 11 subdivision) is also available. And support motors with 0.9 degree or 1.8 degree. Maximum speed 1000RPM. With usart interface, you can connect the computer by serial port, for parameter adjustment and query..
  • Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
  • Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
  • Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User metho....
Check Stock

[3-pack]VINTAR 3-Outlet Adapter Wall Tap Outlet Extender Portable Travel Mini Plug Grounded Indoor AC Outlet White,ETL Listed.

  • [Multi Outlet Extender]-Get more out of your wall outlet with the VINTAR 3-Outlet Adapter Wall Tap that can expand one plug into three.This wall tap....
  • [No Blocking Design] – Vintar wall outlet extender with 3 AC outlets in 3 different directions accepts the standard American 3 prong flat pin plug....
  • [Compact &Lightweight Design] - Easy to carry with mini-size for you put into your briefcases. This electrical outlet extender provides a convenient....
  • [Cruise Ship Must Have] - Most cruise ships don’t allow surge-protected power strips on board for safety reasons. This plug extender has NO surge....
  • [Safety Guaranteed]- Fire-resistant PC shell, and high-quality component can improve durability and safety. And our wall outlet extender is certified....
Check Stock

Barnabas Robotics Servo Motor Tester Kit | 180 Degree 9g Servo Motor + RC Servo Tester Controller + 6V Battery Holder

  • [CONVENIENT, ALL-IN-ONE KIT FOR TESTING SERVO MOTORS] Experiment with servo motors with this all-inclusive kit. Includes 9g servo motor + servo tester controller + 6V battery holder at a low price!.
  • [9G Servo Motor] 180 degree range of motion. Includes 3 types of servo horns..
  • [4 CELL x AA BATTERY HOLDER] Fits 4 x AA batteries, which produces 6V for your servo tester and servo motors..
  • [SERVO TESTER] Includes 3 modes to test servo motors or ESC.
  • [GREAT FOR RC APPLICATIONS] Use as a power source for robotics, RC cars, helicopters, planes, boats and or any hobby projects.
Check Stock

WEISHUJI 25T Servo Horn Steering Arm, Servo Horn 25T Steering Arm, Aluminum 25T Servo Horn Steering Arm for Traxxas TRX4 Axial SCX10 Tamiya 1/10 RC Crawler Truck (Red-Black)

  • 25T Servo Horn Steering Arm fits for Traxxas TRX4 Axial SCX10, SCX10 ii 90046 1:10 scale rc crawler, and Servo Horn 25T Steering Arm is CNC machined..
  • 25T Servo Horn Steering Arm has 18mm and 22mm threaded mounting holes for adjustability, and Servo Horn 25T Steering Arm is of high quality..
  • 25T Servo Horn Steering Arm is Red-Black, and Aluminum 25T Servo Horn Steering Arm is of small size and lightweight..
  • 25T Servo Horn Steering Arm works on Futaba, Savox, Emax, HSP, Power HD, Xcore, Aluminum 25T Servo Horn Steering Arm works on other popular prand servos motor (Except Hitec and JR Servos)..
  • Package of 25T Servo Horn Steering Arm includes: 1 x 25T Servo Arm (Red-Black), Servo Horn 25T Steering Arm, Aluminum 25T Servo Horn Steering Arm.
Check Stock

WEISHUJI 10PCS 25T Aluminum Servo Horns Arms, M3 Threads Metal Steering Arm for Towerpro, HSP, HD power, Futaba, Axial, Savox, Xcore, Standard Servos Motors, MG995 MG996R MG946R, S3003 etc servo (Red)

  • 25T Aluminum Servo Horns Arms are suitable for mostly 25T Standard Servo Motor, and M3 Threads Metal Steering Arm is compatible with Towerpro HSP HD power Futaba Axial Savox Xcore Standard Servos Motors MG995 MG996R MG946R S3003 etc servo..
  • 25T Aluminum Servo Horns Arms are made of strong aluminum, 25T Aluminum Servo Horns M3 Threads are hard to break..
  • 25T Aluminum Servo Horns Arms are of dimension 35x15x6mm, and Metal Steering Arm behaves very well on your RC models..
  • 25T Aluminum Servo Horns Arms are djustable type servo arm, and M3 Threads Metal Steering Arm have two steel bolts to secure the split-clamp onto the servo output..
  • Package of 25T Aluminum Servo Horns Arms include: 10 x 25T Aluminum Servo Horn-Red, M3 Threads Metal Steering Arm, 25T Aluminum Servo Horns M3 Threads some hardware.
Check Stock

WEISHUJI Aluminum Servo Horns,25T Aluminum Servo Horns,Aluminum servo Horn 25T Servo Horn Extension Steering Arm Server Rocker for RC Car Truck Buggy 5Pcs

  • Aluminum Servo Horns are made of High Quality CNC Machined Aluminum, sturdy and durable..
  • 25T Aluminum Servo Horns are compatible with Futaba, Savox, Orion, & Other Popular Servos (25T Aluminum Servo Horns Will Not Work On Hitec Or JR Servos)..
  • Aluminum servo horn 25t Dimension:aluminum servo horn 25t Length: 37mm/1.462 inches..
  • Distance from Servo Horn Extension Steering Arm Server Rocker hole center to Servo Horn Extension Steering Arm Server Rocker hole center：8mm, 11mm, 14mm, 17mm..
  • Package List of Aluminum servo horn 25t includes: 5 * Aluminum servo horn 25t.
Check Stock