15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

  • You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
  • Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
  • Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
  • Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
  • Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.
Check Stock

AITRIP 12PCS TCA9548A I2C IIC Multiplexer Breakout Board Module 8 Channel Expansion Development Board for Arduino

  • The TCA9548A adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use.There are 8 I2C interfaces on one expander, and there are eight bidirectional transfer switches that can be controlled by I2C bus. This means that after 1 expander is transferred, 8 identical addresses can be connected to the same I2C port..
  • Expansion board TCA9548A compatible with IIC bus and system management bus (SMBus), active low reset input, support for hot insertion, low standby current, no glitch during power-up, support for voltages between 1.8V, 2.5V, 3.3V and 5V buses Level shifting, TCA9548A I2C IIC multiplexer breakout board depending on the contents of the programmable control registers, any single SCn/SDn channel or combination of channels can be selected..
  • 12pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino.
Check Stock

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

  • Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
  • Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
  • 2.You should connect higher power supply for higher-power servo.
  • 3.Make sure servo are connected properly, otherwise they will not move..
  • Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
  • Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..
Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

  • 10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
  • Great for jumping from board to board or just about anything else..
  • There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
  • Length:100mm Type:JR Plug Servo Extension wire (Male to Male).
Check Stock

6Pcs ShareGoo JR Style Servo Splitter Cable, 2.75' Servo 1 Male to 2 Female JR Y Harness Y Cable Extension Wire for RC Models Car Airplane Helicopter Drone Boat

  • Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
  • This servo Y-cable allows you to control two servos with one radio channel..
  • Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
  • 3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
  • Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..
Check Stock

waveshare for Raspberry Pi Pico Evaluation Kit B Include Pi Pico Board with Pre-Soldered Header,1.14inch RGB Color LCD, 10DOF IMU Sensor Module,Dual GPIO Expander,Breadboard

  • Raspberry Pi Pico Evaluation Kit inlclude Raspberry Pi Pico with pre-soldered header ,1.14inch LCD Display Module,10-DOF IMU Sensor Module,Dual GPIO Expander ,830 Quality Breadboard etc.
  • Raspberry Pi Pico Board,a tiny, fast, and versatile microcontroller board,Built Using RP2040 Microcontroller Chip Designed By Raspberry Pi.
  • 1.14" LCD Display Module for Pico ,Embedded ST7789 Driver, Using SPI Bus.
  • 10-DOF IMU Sensor Module,an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I2C bus for communication..
  • Dual GPIO Expander for Pico,Two Sets Of Standard Raspberry Pi Pico GPIO Male Headers.
Check Stock

Treedix TCA9548A I2C Multiplexer Breakout Board 8 Channel Expansion Board with pi Header for Arduino

  • The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
  • TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
  • The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
  • In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
  • The chip is compatible with 3V and 5V and can be used with any logic level.
Check Stock

KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino

  • This expansion board can directly stack on the controller R3 board and can drive up to 16 servos.
  • Uses I2C input, just occupy A4 and A5 interface on the control board.
  • Contains PCB double sided holes, can direct to solder with components to build up prototyping circuits.
  • Servo power supply independent V + input up to 6V.
  • How to use: Search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product..
Check Stock

Arduino Uno 3 Ultimate Starter Kit Includes 12 Circuit Learning Guide

  • This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
  • Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
  • Includes a total of over 190 electronic parts and components.
Check Stock

Zeyitian Cup Holder Expander for car beker car Cup Holder for Organizer Adapters Holders Universal Compatible with 2.6 \ o 4.5\ diameters and Most 12-Ounce to 46-Ounce Bottles&Cups

  • FIT: 2.5in x 1.8in cup holder base. The base's retaining block also extends 0.72 inches outwards. This cup holder expander for car works best in cylindrical cup holders.Three clips can hold (2.6 "to 4.5" diameter) bottles. With an adjustable rubber base, our cup holder expander for cars expander is mounted into the car in one step, aligned with your car's cup holder and pushed. The cup holder expander for cars base can be adapted to any shape of the cup holder..
  • AVOID NOISE: The cup holder expander for car is made of solid, thick plastic, and rubber sheets around the top hold the cup firmly in place, preventing it from tipping or spilling over on the road. No tilting or splashing. Rubber pads at the bottom protect the cup and eliminate cup holder expander for cars noise..
  • USAGE TIP: This cup holder expander for car works best in cylindrical cup holders, but some cup holder designs do not work. Be sure to check the product dimensions in the picture and compare them to your specific application before purchasing. For suitable models, we recommend buying a pair. Easy to use and closer to our bodies, the seat three-claw cup holder expander for cars allows your drinks to be at your fingertips..
  • MORE COMPATIBILITY: Suitable for almost anything cup holder expa....
Check Stock

sb components Motor Driver Board for The BBC Micro bit 2 Channel DC Motors and 3 Channel Servos Motors Motor Driver for Micro bit BBC microbit Motor Driver Board

  • micro:bit edge connector, directly pluggable.
  • 2x DC motor interfaces, 3x servo interfaces.
  • Integrates 5V regulator, up to 3A output current.
  • Onboard multi connector options for DC motors in different specifications, onboard standard servo headers.
Check Stock

SYMOTTEC 1/18'' to 3-1/2'' Exhaust Tail Pipe Expander Muffler Spreader Tool Set Compatible with Most Vehicles and Trucks

  • This Exhaust Pipe Expander Muffler Spreader Tool Set is designed to quickly and easily straighten clamp dents and clamp marks in mufflers and tail pipes, and stretch pipe openings or fix damaged pipe ends. Can be use with a hand ratchet or breaker bar and also a hand wrenches..
  • This Tail Pipe Expander set includes three different expander sizes, can work with all 1-1/8inch to 3-1/2inch ID thin-wall pipes and compatible with most vehicles and trucks..
  • Drop forged and heat treated steel construction for strength and hardness and through strict quality inspection. Suitable for family and professional mechanic. Plug and play, you can buy it with confidence..
  • Kit Includes 1 x small expander: 1-1/8" to 1-3/4", 1 x medium expander: 1-1/2" to 2-1/2", 1 x large Expander: 2-1/8" to 3-1/2, 6 x extra O-rings..
  • IMPORTANT NOTICE!!! (1) When expanding, the beveled steel cones of the expander must be fully inserted into the pipe, not half.
  • (2) Try to use a manual ratchet or manual wrench to turn the pipe support tool to expand the pipe, rather than electric Ratchet.
Check Stock

ABN Exhaust Pipe Expander Tool - Tail Pipe Expander Exhaust Expander, Exhaust Pipe Stretcher Kit 1-5/18 to 4-1/4 Inch

  • [Increase Engine RPM]: Expanding your tailpipe with the ABN Exhaust Tube Expander Tailpipe Expander Kit to increase exhaust volume and to give you more power for your engine.
  • [Easy to Use]: Lubricate all parts of the exhaust pipe bender stretch tool and attach correct sleeve.
  • Insert pipe spread tool into pipe, connect to existing drill, and expand.
  • Pipe might need to be warmed during winter months to prevent damage while using exhaust flare tool.
  • [Expand Most Metals]: Tailpipe expander tool kit great for all types of pipes, from aluminum to stainless steel.
  • Exhaust pipe expanding tool can expand piping from 1-5/18 to 4-1/4 inches (3.3 to 10.8cm).
  • [Easy Storage]: HVAC pipe expander parts come in a plastic storage case to keep the steel and copper pipe expander kit organized.
  • [Contents]: Exhaust pipe expansion tool kit includes a 3/4-inch and 1/2-inch (1.9 and 1.3cm) shank collet expander chuck, 5 expander sleeves, and 2 packs of black rubber O ring replacements.
Check Stock