Categories

Best Servo To I2c Board

AITRIP 12PCS TCA9548A I2C IIC Multiplexer Breakout Board Module 8 Channel Expansion Development Board for Arduino

  • The TCA9548A adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use.There are 8 I2C interfaces on one expander, and there are eight bidirectional transfer switches that can be controlled by I2C bus. This means that after 1 expander is transferred, 8 identical addresses can be connected to the same I2C port..
  • Expansion board TCA9548A compatible with IIC bus and system management bus (SMBus), active low reset input, support for hot insertion, low standby current, no glitch during power-up, support for voltages between 1.8V, 2.5V, 3.3V and 5V buses Level shifting, TCA9548A I2C IIC multiplexer breakout board depending on the contents of the programmable control registers, any single SCn/SDn channel or combination of channels can be selected..
  • 12pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino.
Check Stock

HiLetgo 5pcs Nano I/O Expansion Sensor Shield for Arduino UNO R1 Nano 3.0 Duemilanove 2009

  • 14 I/O Pin (servo type with GND, power and signal).
Check Stock

ACEIRMC 8pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino

  • The adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use..
  • TCA9548 TCA9548A 1-to-8 I2C 8 -way multi-channel Expansion Board IIC Module Development Board.
Check Stock

AITRIP 10PCS PCF8574 PCF8574T IO Expansion Board I/O Expander I2C Evaluation Develop Module

  • The PCF8574 IO Expansion Board provides general-purpose remote I O expansion via the two-wire bidirectional I2C-bus (serial clock (SCL), serial data (SDA)..
  • The main resources: PCF8574, I2C interface, the 8-bit parallel.
  • Typical applications: for I / O resource constraints the MCU I / O expansion.
  • PCF8574T expansion board applicable to a variety of platforms including AVR / ARM.
  • PCF8574T PCF8574 IO expansion board support I2C bus cascade (by pin header row seat docking methods can be used simultaneously multiple I2C modules).
Check Stock

SunFounder Raspberry Pi Pico Ultimate Starter Kit with Detailed Online Tutorials, 320+ Items, 113 Projects, MicroPython, Piper Make and C/C++ (Compatible with Arduino IDE)

  • 【Ultimate Raspberry Pi Pico Kit】Contains over 320 items and 113 online projects for all Arduino and Raspberry Pi users, from beginners to advanced programmers..
  • 【320+ Items】Besides the Pi Pico board, it also comes with an ESP8266 module for projects involving the Internet of Things. There are all the necessary components included: Sensors (MPU6050, DHT11, Ultrasonic, etc), Actuator LEDs, I2C LCDs, WS2812 RGB LED strips, Servo Motor, and Pump, etc..
  • 【Pre-soldered Raspberry Pi Pico Included】The Raspberry Pi Pico is a high-performance microcontroller board with flexible digital that features the RP2040 with a dual-core ARM Cortex-M0+ processor..
  • 【Provided 113 Projects】This Pi Pico Kit contains 113 professional projects of varying complexity. In each lesson, we provide circuit diagrams, a description of how it works, and an explanation of the code..
  • 【3 Programming Languages】Raspberry Pi Pico Ultimate kit features three programming languages to meet the needs of programmers of every level: 59 MicroPython lessons, 38 lessons in C/C++, and 16 lessons in Piper Make..
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

SunFounder Raspberry Pi Pico W Ultimate Starter Kit with Online Tutorials, 450+ Items, 117 Projects, MicroPython, Piper Make and C/C++ (Compatible with Arduino IDE)

  • 【Ultimate Raspberry Pi Pico W Kit】Contains over 450+ items and 117 online projects for Arduino and Raspberry Pi Pico W users, from beginners to advanced programmers..
  • 【450+ Items】Aside from the Pi Pico W boards, all the necessary components are also included: Sensors (MPU6050, DHT11, Ultrasonics), Actuators, LEDs, I2C LCDs, RGB LED strips, Servo motor, and Pump,etc..
  • 【Pre-soldered Raspberry Pi Pico W Included】The Raspberry Pi Pico W is an RP2040-based microcontroller board with wireless (802.11n)..
  • 【Provided 117 Projects】The Pi Pico W Kit contains 117 professional projects varying in complexity.It contains 9 examples of IoT protocols for IFTTT, MQTT,etc..
  • 【3 Programming Languages】Raspberry Pi Pico W Ultimate kit features three programming languages to meet the needs of programmers of every level: 62 MicroPython lessons, 39 lessons in C/C++, and 16 lessons in Piper Make..
Check Stock

OSOYOO Smart House IoT Starter Kit for Arduino MEGA2560,Learning STEM Electronic Engineering Coding Programming, DIY Home Automation Building Set for Teens Adults

  • ...ERYTHING YOU NEED: Includes Everything You Need To Build & Engineer Your IoT Home Kit: Wooden House Model, OSOYOO MEGA2560 Board, MEGA IoT Extension Board with an ESP12s wi-fi module, and various home automation devices: RFID, Flame Detection Modules,LED, Temperature & Humidity, PIR Motion Ultrasonic, Micro Servo Motor, 1602 I2C LCD Module, Button Modules, RGB Photosensitive, Buzzer, PnP Jumpers, Cables, & More..
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

HiLetgo MCP4725 12 Bit I2C IIC DAC Development Board Breakout Board Internal EEPROM Store Settings for Arduino

  • The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC)..
  • A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller..
  • On board are SCL, SDA, VCC, and another GND for your basic I2C pinout..
  • If you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.store settings.
  • Digital to analog converters are greInternal EEPROM to store settingsat for sound generation, musical instruments, and many other creative projects!.
Check Stock

Aoicrie 5pcs PCA9685 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit, for Robot or for Raspberry pi Shield Module servo Shield

  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)..
  • Communication Interface: IIC, PCA9685 contain an I2C-controlled PWM driver with a built-in clock..
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs..
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate..
  • 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or for Raspberry pi shield module servo shield..
Check Stock

Clock Splitter, Electronic Component Stable for Home for Industry

  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
Check Stock

SparkFun Qwiic Single Relay-Up to 5.5A at 240VAC Multiple I2C addresses Available Turn on/Off high Power Device from Low Power microcontroller No Soldering Large Power Loads w/Simple I2C Commands

  • Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino compatible board or another low powered microcontroller? No soldering needed to get started. Plug and play. Code available. Small footprint..
  • The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!.
  • The Qwiic Relay comes with a default I2C address of 0x18 but can be changed with a simple command allowing you to control over 100 Qwiic Relays on a single bus (but please be aware that toggling lots of relays on a 3.3V bus can cause voltage spikes so an external power supply will be required)!.
  • In addition, there is an address jumper on the back of the board. Closing this jumper with solder will change the address to 0x19..
  • Operating Voltage: 1.7V-3.6V. Coil Resistance: 23.5Ω. I2C Address: 0x18 (Default), (Jumper changes to 0x19). Max Current (Through Relay): 5.5A (240 VAC).
Check Stock