Categories

Best Servo To Pwm Converter Board

ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire

  • ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
  • FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
  • This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Check Stock

CURT 59236 Weather-Resistant Multi-Function Splice-in Trailer Tail Light Converter Kit, 4-Pin Wiring Harness

  • FULLY SEALED. This trailer light converter features an epoxy-filled, potted enclosure that seals off the electrical components from moisture and vibrations, promoting increased longevity.
  • HIGHLY VERSATILE. This multi-functional taillight converter can be used to convert 2-wire, 3-wire, PWM ST and PWM STT systems to standard 2-wire trailer wiring. It is also compatible with low-voltage operation as low as 7 volts.
  • PROTECTED. This multipurpose tail light converter is equipped with a microcontroller that senses current to rapidly respond to overload. It also offers improved short-circuit and thermal protection.
  • STANDARD OUTPUT. This tail light converter provides a standard 4-way flat socket to connect the taillights, brake lights and turn signals for towing.
  • READY TO INSTALL. This trailer light converter comes ready to install on your vehicle. It includes a wiring kit to establish a connection to the vehicle battery, as well as snap locks for secure connection of the wires. No heavy-duty flashers required.
Check Stock

Aoicrie 5pcs PCA9685 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit, for Robot or for Raspberry pi Shield Module servo Shield

  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)..
  • Communication Interface: IIC, PCA9685 contain an I2C-controlled PWM driver with a built-in clock..
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs..
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate..
  • 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or for Raspberry pi shield module servo shield..
Check Stock

ALAMSCN 5PCS SG90 9g Servo Motor + 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit DIY Kit for RC Robot Arm Helicopter Airplane Car Boat Remote Control for Arduino for Raspberry pi

  • These SG90 9G micro servo motors have a completely new redesigned PCB and control system to provide more accuracy..
  • Its internal gearing and motor are also upgraded to improve dead bandwidth and centering..
  • For SG90 9G micro servo motor is far more accurate and safe to use in aircraft which require precise servo movements and perfect centering..
  • Apply to remote control helicopters, micro robot, robot arm and boats. Fit for ALL kind of R/C Toys and also make electronics DIY based on Arduino ,Raspberry Pi..
  • Package includes: 5PCS SG90 9g Micro Servo + 1PC PWM Servo Motor Driver. Cost-effective kit to meet your DIY needs..
Check Stock

ZOSKAY 1X DS3218 Update servo 20KG Full Metal Gear Digital servo Baja servo Waterproof servo for Baja Cars(Control Angle 180)

  • DS3218 20KG Large Torque Digital Servo with precision potentiometers,stable,low noise,waterproof: IP66.
  • High-precision metal gears with hard anodizing, CNC aluminium middle Shell, Dual ball bearings.
  • Large Torque&speed – 18.5kg.cm (0.16S/ 60°)@5V,maximum 21.5 kg.cm (0.14S/60°)@6.8V Operating travel:180°（PWM 500-2500μs）.
  • High performance digital standard servo for any crawler.
  • and for robot joint activities,TRX 4 Traxxas， SMT10 Mega Truck， SCX10 II，ARRMA Nero 1/8…..
  • Package Included: 1 x Digital Servo 1.58x0.79x1.60inch (40x20x40.5mm).
  • Weight: 60g (2.12oz) 1 x 25T Adjustable metal servo arm.
Check Stock

HiLetgo 5pcs Nano I/O Expansion Sensor Shield for Arduino UNO R1 Nano 3.0 Duemilanove 2009

  • 14 I/O Pin (servo type with GND, power and signal).
Check Stock

Treedix 2pcs ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Treedix ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter with Cable

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Analog Voltage to PWM Signal Converter, 0-5V/0-10V Analog Input Voltage to 0-100% PWM Signal 2KHZ-20KHZ Converter Module,for PWM Motor Speed Control Interface Circuit Activity

  • Voltage to PWM Signal Converter Module: This module can convert 0-5V or 0-10V analog input voltage into 0-100% PWM signal..
  • Wide Application: This module is widely used for PWM motor speed control interface circuit, instrumentation AD interface conversion, and other applications that need convert voltage to PWM signal..
  • PWM Signal Frequency Range: The PWM signal frequency range is 2KHZ-20KHZ, maximum is 20KHZ, default minimum is 2KHZ,Hyuduo is committed to providing customers with high-quality products and thoughtful service..
  • Setable Output Frequency: The default function of this module is converting 0-10V into 0-100% 2KHZ PWM signal, but the output frequency can be set by adjusting potentiometer as needed,stable and reliable performance, practical, easy to operate and use, has a long service life..
  • Two Kinds of PWM Signal: There are two kinds of PWM signal, PNP-PWM output and NPN-PWM output. The PNP-PWM output is only 5V level, NPN-PWM output is 5V and 24V level,If you have any problem,please contact us, we will strive to provide you with satisfactory service!.
Check Stock

QWinOut 8CH Receiver PWM to PPM Sbus Dbus S-Bus Encoder Signal Converter Module Compatible for DJI Phantom 2 Xaircraft Minix Superx V2

  • Effective Picture Only, Product Do Not Include The Receiver!.
  • With This Signal Converter, You Can Be in Average ELF With Ordinary Remote Receiver and Remote Control, and Don't Have to Use Average of Original Remote Control.
  • With This Signal Converter, You Can Put The Average ELF Remote Control Used in The Ordinary Plane (ELF SBUS For The Remote Control Receiver Signal is Converted Into Common PWM Signal Available To Ordinary Electric Harmonic Steering Gear).
  • With This Signal Converter, You Can Put The Ordinary Ppm Signal Of The Remote Control Interface (Coach) Into PMW Signal (The Equivalent of a Cable Receiver, Converted To Ordinary PWM Signal Available to Ordinary Electric Harmonic Steering Gear).
  • Compatibility:  compatible for DJI S.Bus Flight Control and Gimbal, Xaircraft Minix or Superx V2.
Check Stock

AEDIKO MG996R Servo Motor Control 180 Angle Metal Gear Servo Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter 2-Pack (MG996)

  • Positioning Speed Without Load: 0.17s / 60 degrees 4.8V.
  • Compliant with Futaba, Hitec, Sanwa, GWS, etc ..
  • Latest Version: MG996R Servo Motor Which Updated from SG90 and MG90S Micro Servo Motor,Made of High Precision Potentiometer and High Resolution Digital Chip to Ensure Stable Performance and Solve Problems:Unsuitable R / C and Slow Response Time.
  • Gear Type: All Metal Gear RC Servo Can Control the Angle Range from 0 to 180, with Precise Control and Gears are Consistent,Which Can Rotate 360 Degrees When Power Off.
  • Application: Analog Servo Motor Great for RC Helicopters, Micro Robots,Robotic Arms and RC Rock Crawler, RC Boat Motor,Truck, Boat, Racing Car,Various Remote Control Toys and Arduino Experiments.
Check Stock

15 Pieces Servo Extension Cables Servo Extension Male to Female RC Servo Extension Cord Wire Cable Compatible with RC JR Futaba RC Car Airplanes (3.9 Inch,5.9 Inch,11.8 Inch,19.7 Inch,23.6 Inch)

  • Wide application: these servo extension s are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also nice for remote control car, RC car and more.
  • Appropriate sizes: the servo extension cord measures approx. 3.9 Inch, 5.9 Inch, 11.8 Inch, 19.7 Inch, 23.6 Inch in length, different size for your use, the color is black and red.
  • Package includes: this package includes 15 pieces of male to female servo extension cables, enough quantity for you to use and replacement, providing more convenience for you.
  • Feature: this male to female servo extension cord featured with female connector on one side, and male connector on the other side, can be connected to the receiving set and steering engine.
  • Useful function: the servo extension wire is suitable for jumping from board to board, or can be applied to control panel cable remote control, which is male to female.
Check Stock

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA)，PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock