Best Single Ended Triode Amplifier

Taidacent AD8130 Differential Receiver Amplifier Module Differential to Single-ended High Common-mode Rejection Ratio Low Noise Low Distortion

• Name: AD8130 Differential Amplifier Size: 43mm X 38mm Supply voltage range: ±5V~±12V.
• The differential-to-single-ended amplifier, which has a 270-MHz bandwidth and a very high common-mode rejection ratio (CMRR) at high frequencies, can also be effectively used as a high-speed instrumentation amplifier or to convert a differential signal to a single-ended signal..
• Differential amplifiers can process single-ended inputs as interactive differential outputs or treat differential inputs as differential outputs. These amplifiers have two independent feedback loops that control the differential and common-film output voltages, respectively..
• Chip features 1. High speed AD8130: 270 MHz, 1090 V/us (G= +1) AD8129: 200 MHz, 1060 V/us (G= +10) 2. High Common Mode Rejection Ratio (CMRR) 94 dB (minimum, DCE100 kHz) 80 dB (minimum, 2 MHz) 70 dB (10 MHz) 3. High input impedance: 1 MQ differential 4. Low noise AD8130: 12.5 nV/Hz AD8129: 4.5 nV/vHz.
• 5. Input common mode range: ±10.5V 6 low distortion, 1V peak-to-peak (5 MHz): AD8130, -79 dBc (Worst Harmonic, 5 MHz AD8129, -74 dBc (Worst Harmonic, 5 MHz) 7. User adjustable gain G= +1 without external components 8. Supply Voltage Range: +4.5V to ±12.6V 9. Power saving mode.

MUZISHARE X7 KT88 x4 Vacuum Tube Integrated Amplifier Push-Pull Power Amp MM Phono Tube Amplifier Balanced XLR 2022 Remote

• MUZISHARE X7 Upgraded version. Upgraded the internal coupling capacitor, is the designer to debug the custom-made silver film capacitor, relative to the classic version of the extension, control, density is better..
• MUZISHARE X7 is an integrated Amplifier. This is also a Power Amplifier (there is a group pre-amp input), a Headphone amplifier and this is a amplifier for Phono player too, direct link your phono player to this amplifier to output to speakers..
• Pure Handmade,point to point hand welding using two high-quality wide-frequency high-quality Japanese EI output transformer using a high-power Z11 core toroidal power transformer dedicated designed for the machine ， voltage amplification and promote are used tube 5AR4 for rectifier power supply..
• Use 12AX7 and 12AU7 vacuum tube for voltage amplification and phase inversion,use KT88 vacuum tube to do AB1 push-pull power amplification.
• Mute delay function when turn on the amp(about 30 seconds) ；the choice of Japanese ALPS motor potentiometer.
• Provide Triode and Ultralinear selection function: Triode work mode. soft. pure and sleek. suitable for enjoying vocals. strings Music and other types of music.
• Ultralinear work. the sound of open. unrestrained. the momentum is good. for large scenes. large dyn....

Tim Burton's The Nightmare Before Christmas

• This amplifier can be used with KT88 or EL34 vacuum tube, and there is a Red selection button on the Back of the amp to switch. The default matching tubes of this machine is KT88. If you need EL34 tubes, please purchase separately..
• Pure hand-made, the whole machine is welded with scaffolding..
• Can be used as an Integrated amplifier, power amplifier or Headphone amplifier.
• Triode and ultra-linear selection are available, which can be switched by the button on the amplifier.
• With a remote control,Vacuum tube protective cover,Fuse and an English manual..

Taidacent THS4131 Fully Differential Input/Output Low Noise Amplifier Module Single Ended to Differential Single Ended Input Double Ended Output

• Name: THS4131 Fully Differential Amplifier Size: 45mm X 34mm Supply Voltage Range: 5V Single Supply ±15V Dual Supply.
• This module can implement single-ended to differential, single-ended input, and double-ended output. Has high performance, low noise, wide power supply voltage range and other advantages..
• The THS413x consists of a true fully differential signal path from input to output. This design produced excellent common-mode noise suppression wells that improved total harmonic distortion..
• Chip features High performance 150 MHz - 3 dB bandwidth (VCC = ±15V) 51V/us slew rate -100dB third harmonic distortion (250kHz) 2. Low noise 1.3 nV/vHz Input Reference Noise Differential input/cent output Balanced Output Suppresses Common Mode Noise Reduce second harmonic distortion from dry differential output.
• Wide supply voltage range VCC-5 V Single Supply to ±15V Dual Supply ICC (SD) = 860 u A Shutdown Mode (THS4130) Chip application Single-ended to differential conversion Differential ADC Driver Differential antialiasing Differential transmitters and receivers Output Level Translator.

Willsenton R8 KT88/EL34 x4 Tube Integrated AMP Power Amplifier Headphone Replaceable Basic Meter (Black)

• This amplifier can be used with KT88 or EL34 vacuum tube, and there is a Red selection button on the Back of the amp to switch. The default matching tubes of this machine is KT88. If you need EL34 tubes, please purchase separately..
• Pure hand-made, the whole machine is welded with scaffolding..
• Can be used as an Integrated amplifier, power amplifier or Headphone amplifier.
• Triode and ultra-linear selection are available, which can be switched by the button on the amplifier.
• With a remote control,Vacuum tube protective cover,Fuse and an English manual..

HIFIMAN EF400 Desktop Balanced Headphone DAC& Amplifier with Himalaya R2R DAC, 3.5/4.4/6.35mm Output for Home Audio

• ...c signal transmitted by the most common IIS (Integrated Interface of Sound) audio interface, with a maximum resolution of 24Bit..
• Full Balance: The four-channel differential structure features a DAC, buffer and active filter that add up to unbeatable fully balanced output for stunning performance from a Class AB DAC/amplifier. The four-channel fully differential amplifier circuit features a maximum output of 10.7 Vrms (THD.
• 4-level Function Switch: High Gain NOS, High Gain OS, Low Gain OS, Low Gain NOS ★Headphone Out (Front Panel): 6.35mm Single-ended.
• XLR 4-Pin Balanced Output. ★Line Out (Rear Panel): CANNON Balanced Output.
• RCA (Single-ended).★ Input: USB Type C.

Triton Audio FetHead in-Line Microphone Preamp

TRITON AUDIO FetHead Phantom In-Line Microphone Preamp

TRITON AUDIO FetHead Filter In-Line Microphone Preamp

SMSL HO200 Hi-Res Balanced Headphone Amplifier Low Noise 4xPLFC RCA/XLR Input 6.35mm 4.4mm XLR Balanced Output HiFi Preamp Headphone Amplifiers with High Mid Low Gain Control for AO200

• √ High Power Output: SMSL HO200 not only can be used as a headphone amplifier, but also can be used as a Hi-End Pre Amplifier. At the output power of 16 ohms power up to 6W, 32 ohms at 3w!.
• √ Low Noise Headphone Amplifier: 4 x PLFC ultra-low distortion precision linear feedback circuits are used. Distortion as low as 0.00006%, signal-to-noise ratio up to 140dB!.
• √ Balanced / Single-ended Output: HO200 provides 4 core XLR balanced, 4.4 balanced and 6.35 single-ended headphone output interface respectively, to meet the needs of different headphones!.
• √ Three-step Gain Switching Switch: Using the classic toggle switch rotary button, there are high, medium and low three-step gain switching switch. More convenient to switch gain control, where the low gain is optimized for IEM only!.
• √ Streamlined Design: Anodized technology, external aluminum CNC machining shell, fine workmanship, ultra-compact design, simply the top of the desktop headphone system!.

Digital Microphone Amplifier, Reverberation Board Low Noise for Audio Equipments

• For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples..
• Cond over I2C,The chip can be configured as 4 single-ended input channels, or two differential channels..
• As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range..
• We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 12 bit converter..
• The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed , you can have up to 4 ADS1015's connected on a single 2-wire I2C bus for 16 single ended inputs..

Taidacent INA114 Instrumentation Amplifier 1000 Times Gain Adjustable Single-Supply Operation Single-Ended/Differential Input

• INA114 is a low-cost, high-precision instrumentation amplifier that only requires an external resistor to set the gain, and the gain range is 1 to 10000..
• the weak signal detection effect is excellent, and can input single-ended signals or differential signals..
• Chip features: Offset voltage 50uV, drift 0.25μV/℃, and high common mode suppression, 115dB when G=1000.
• Module application: bridge amplifier, thermocouple amplifier, RTD sensor amplifier, medical equipment, data acquisition front end.

Willsenton R8 KT88/EL34 x4 Tube Amplifier Integrated AMP Power Headphone Replaceable Basic Meter(Silver)

• One amplifier can used wiht tube EL34, KT88 or 6550, so, you can get 3 kinds of sound from different models tubes. The default matching tubes of this machine is KT88. If you need another 2 new sets of tube, please purchase in addition. There is a Red selection button on the Back of the amp to switch..
• Pure hand-made, the whole machine is welded with scaffolding..
• Can be used as an Integrated amplifier, power amplifier or Headphone amplifier.
• Triode and ultra-linear selection are available, which can be switched by the button on the amplifier. With a remote control,Vacuum tube protective cover,Fuse and an English manual..
• We recommend that you spend 100-300 hours to RUN-IN this amplifier to get a better sound. Generally, you could get a better and stable sound after 100 hours, and you could get the best sound after accumulating more than 300 hours..