Categories

Best Spi Equipment

HiLetgo 1602 LCD Keypad Shield 1602 LCD Expansion Shield Board Blue Backlight 4.5-5.5V for Arduino Duemilanove Robot

  • ☆ Premium Quality: Made of premium material, this lcd module display is sturdy, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage.
  • ☆ TFT LCD Serial Port Module : The lcd display module is a new 2.8 inch serial SPI color display module. Designed with one socket for sd card and PCB adapter for LCD.
  • ☆ Come With PCB Plate: With PCB plate (including power supply IC, SD), pcb display module is compatible with 5110 interface. Resolution: 128x160.
  • ☆ Support Analog & Hardware SPI: This tft display module supports analog SPI and hardware SPI, less I/O port need. It can be driven by 8051 / AVR / PIC /ARM/STM32. It can be driven with at least four IO.
  • ☆ What You Will Get: If you need the document to download, please contact us. We stand behind all of our them with a 100% product guarantee and promise to give you the best in customer care.
Check Stock

LED LCD Universal TV Backlight Constant Current Backlight Lamp Driver Board Boost Step Up Module 10.8-24V to 15-80V 14-37 Inch

  • This is a new 1.8 inch serial SPI color display module.
  • Support analog SPI and hardware SPI. SPI serial, less I/O port need.
  • Designed with one socket for sd card and PCB adapter for LCD.
  • It can be driven by 8051 / AVR / PIC /ARM/STM32.
Check Stock

DORHEA 2Pcs BME280 5V Temperature Humidity Atmospheric Barometric Pressure Sensor Module GY-BME280-5V IIC I2C Breakout Board

  • The BME280 sensor is a precision sensor, is soldered onto PCB, not only the pressure and the temperature, this sensor can measure humidity..
  • BME280 5V uses both I2C and SPI (supports 3-, 4-wire SPI) interface. Interface: I2C (up to 3.4MHz).
  • Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI. for simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI..
  • The BME280 stmospheric pressure sensor is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings..
  • The BME280 sensor is precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy..
Check Stock

Happymodel Mobula6 Quadcopter Indoor Four-axis 1S 65mm Brushless Bwhoop Drone BNF AIO 4IN1 Crazybee F4 Lite Flight Controll Built-in 5.8G VTX Parts Without Remote Controller (25000KV Frsky RX)

  • Flight controller: (Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR.
  • (Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS.
  • Onboard 4in1 ESC: MCU upgraded to EFM8BB21.
  • Current: 5A continuous peak 6A (3 seconds).
  • OnboardFrsky SPI D8 receiver Version: SPI BUS receiver Frsky D8 compatible.
  • No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m.
  • OnboardFlysky SPIreceiver Version: SPI BUS receiver.
  • No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m.
Check Stock

SparkFun MicroMod Artemis Processor - Modular Interface Ecosystem That Connects Artemis microcontroller/Processor Board to Various/Carrier Board peripherals

  • Artemis General Features: 1M Flash / 384k RAM, 48MHz / 96MHz turbo available, 6uA/MHz (operates less than 5mW at full operation), 48 GPIO - all interrupt capable, 31 PWM channels, Built in BLE radio and antenna.
  • Additional Artemis Features: 10 ADC channels with 14-bit precision with up to 2.67, million samples per second effective continuous, multi-slot sampling rate.
  • Additional Artemis Features: 2 channel differential ADC, 2 UARTs, 6 I2C buses, 6 SPI buses, 2/4/8-bit SPI bus, PDM interface, I2S Interface, Secure 'Smart Card' interface, FCC/IC/CE Certified (ID Number 2ASW8-ART3MIS).
  • Specific Peripherals made available on MicroMod Artemis: 1x USB dedicated for programming and debug, 1x UART with flow control, 2x I2C, 1x SPI, 1x Quad-SPI, 8x Fast GPIO, 2x Digital Pins, 2x Analog Pins, 2x PWM, 1x Differential ADC pair, Status LED, VIN Level ADC.
  • Additional peripherals are available but are shared on dedicated MicroMod pins. Processor board only, additional carrier board(s) will be needed to use..
Check Stock

HAPPYMODEL Mobula6 1S 65mm Brushless Whoop Drone Mobula 6 BNF AIO 4IN1 Crazybee F4 Lite Flight Controller Built-in 5.8G VTX RC Toy Gift (25000KV Frsky)

  • Flight Controller: (Frsky SPI RX Version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR.
  • (Flysky SPI RX Version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS.
  • Receiver Option: Internal SPI Frsky Version (Compatible with ACCST D8/D16, Recommend Non EU transmitter D8 mode).
  • Internal SPI Flysky version(Compatible with AFHDS 8CH and AFHDS-2A 14CH Flysky transmitter).
  • Motor Speed Option: SE0802 KV25000(Race Edition).
  • Onboard 4in1 ESC : Support BLHeliSuite Programmable.
  • AIO 4IN1 Crazybee F4 Lite Flight Controller built-in 5.8G VTX.
  • Extreme Light 1S 65mm Brushless Whoop only 20g.
  • Runcam Nano3 The Lightest 1/3 CMOS 800TVL Camera.
Check Stock

3.3V 2.4 inch TFT LCD Touch Panel for Industry with PCB ILI9341 240x320 Pixels for Home

  • This is a new 2.8 inch serial SPI color display module with touch function, 5V compatible, use with 3.3V or 5V logic..
  • Support analog SPI and hardware SPI, Designed with one socket for memory card..
  • With PCB plate (including power supply IC, Memory Card), compatible with 5110 interface..
  • This kit requires professional knowledge and ability, please make sure you know how to use it..
  • Please note that the new type and old type of this product will be sent randomly, and make sure you will not mind before ordering..
Check Stock

SEEU. AGAIN 4pcs 0.96 Inch I2C OLED Display Module IIC SSD1306 128x64 LCD White with 4 Pin Female to Female Du-pont Wire

  • I2C mode up to 400Khz, configurable slave address.
  • Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
  • 4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
  • Backlight brightness and contrast controlled by software commands.
  • Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.
Check Stock

ACEIRMC 3pcs W5500 SPI to LAN Ethernet Network Module TCP IP STM32 Interface 3.3V 5V for Arduino WIZ820io RC5

  • Power supply mode:3.3V external power supply, current should be more than 200mA.
  • USR-ES1 is the Ethernet module of a SPI interface, interface is TTL level of 3.3V, power supply voltage of +3.3V, please ensure that the current is not less than 200mA, voltage is continuous and stable +3.3V..
  • W5500 SPI to LAN Ethernet Network Module TCP IP STM32 Interface 3.3V 5V for Arduino WIZ820io RC5.
  • Control interface:The TTL level, 3.3V SPI interface.
Check Stock

HiLetgo RFID Kit - Mifare RC522 RF IC Card Sensor Module + S50 Blank Card + Key Ring for Arduino Raspberry Pi

  • The MF522-AN module design the circuit of card read by using the original Philips MFRC522 chip..
  • Easy to use, low cost, and applicable to equipment development and card reader development etc..
  • Applicable for the user who need to design or manufacture the RF card terminal..
  • The module can be directly loaded into the various reader molds..
  • The module use a voltage of 3.3V, it can connected communication with user's any CPU mainboard through several lines of SPI interface, it can ensure stable and reliable work, and reader distance..
Check Stock

Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit

  • Perfect for microcontroller storage and retrieval - whether it's images, fonts, GIFs, audio files, or sensor logs.
  • Multi-pin data protocol (up to 4 data pins at once!).
  • Can be used with SDIO hardware support - clocked faster that SPI.
Check Stock

HiLetgo 3pcs RFID Kit - Mifare RC522 RF IC Card Sensor Module + S50 Blank Card + Key Ring for Arduino Raspberry Pi

  • The MF522-AN module design the circuit of card read by using the original Philips MFRC522 chip..
  • Easy to use, low cost, and applicable to equipment development and card reader development etc..
  • Applicable for the user who need to design or manufacture the RF card terminal..
  • The module can be directly loaded into the various reader molds..
  • The module use a voltage of 3.3V, it can connected communication with user's any CPU mainboard through several lines of SPI interface, it can ensure stable and reliable work, and reader distance..
Check Stock

Adafruit ItsyBitsy M4 Express Featuring ATSAMD51

  • The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino M0's and M4s but does not work on Uno (328P) and may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds..
  • This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can use it in Soft AP mode to create an ad-hoc network. For secure client connections, there is TLS 1.2 support in firmware 19.4.4!.
  • Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC..
  • There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data..
Check Stock